X96max+ with IP1001M gigbitye ethernet not working

[manalwong]

Hi Ophub, the lastest release seems to be included the driver for IP1001M right?

However I just test with my box, the device can boot up but no eth0 can not came up.

I had changed the uEnv file to dtb 'meson-sm1-x96-max-plus-ip1001m.dtb' with no lucky, please advise.

the error message seems to said: 'ff3f0000.ethernet xxx cannot attach to phy (error: -19)'

[ophub]

ophub/amlogic-s9xxx-armbian#258

Ask someone who has this device to measure before. But the measurement results are different. You measure and feed back your results.

[manalwong]

48:3.34
49:3.34
50:0.18
51:0.18
53:0.178
7: 0.18
8: 3.34

Is it something wrong?

[ophub]

It was reported that there were contrary test results

[manalwong]

So it can be supported or not?

[ophub]

@manalwong

meson-sm1-x96-max-plus-ip1001m.dtb.zip

Download this file and unzip it, then overwrite /boot/dtb/amlogic/meson-sm1-x96-max-plus-ip1001m.dtb with the same name file, restart and try.

Feedback the test results.

[manalwong]

Wow! Big ophub, you are rock! It works!!!

From iperf test:
Upload: about 860 Mbps
Download: about 826 Mbps

[Test result]
x96max+ iperf test result.txt

[manalwong]

Anything else informations that you want from my box?

[ophub]

amlogic-s9xxx-openwrt/amlogic-s9xxx/common-files/rootfs/etc/model_database.txt

Line 41 in 50dead3

503:X96 Max+ (IP1001M phy):s905x3:meson-sm1-x96-max-plus-ip1001m.dtb:u-boot-x96maxplus.bin:/lib/u-boot/x96maxplus-u-boot.bin.sd.bin:/lib/u-boot/hk1box-bootloader.img:4C@2208Mhz,4GB Mem,1Gb Nic (IP1001M phy),brcm4354 wifi

The dtb file was replaced in the usb. If it can be driven normally after restarting, is it convenient to write emmc to test it?

If you need to keep the Android system in emmc, you can run the openwrt system in the usb first and use openwrt-ddbr for backup. You can use this command to restore Android later.

If it is convenient to remove the shell, take a photo of the front and back of the motherboard, and take a close-up of this chip that can clearly see the number.

Your speed is not full. There are a total of 15 configuration schemes. If you are convenient, I will generate 15 dtb files for you. You can test which iperf3 test result is the best, and it is convenient to determine the scheme.

[Zas09]

Wow! Big ophub, you are rock! It works!!!

From iperf test: Upload: about 860 Mbps Download: about 826 Mbps

[Test result] x96max+ iperf test result.txt

Hello, what is kernel did u flashed ur box? I have same box x96max plus ai2 , ip1001m ... I already test to flash but failed 😭

[ophub]

meson-sm1-x96-max-plus-ip1001m.dtb

https://github.com/ophub/amlogic-s9xxx-armbian/blob/d3fcaac61334983605d2d4a2475354309cbda626/build-armbian/common-files/rootfs/etc/amlogic_model_database.conf#L94

[Zas09]

meson-sm1-x96-max-plus-ip1001m.dtb

https://github.com/ophub/amlogic-s9xxx-armbian/blob/d3fcaac61334983605d2d4a2475354309cbda626/build-armbian/common-files/rootfs/etc/amlogic_model_database.conf#L94

Thanks