F16-DED

This code is used to create an F16 DED using the following hardware

• 2.8" OLED Module 256x64 display. Must be SSD1322 compatible
  • Amazon: https://www.amazon.com/gp/product/B0CHPCRLVF
  • See: docs/7-1.jpg & docs/8-1.jpg for display manual
• ESP32 Dev Board (esp32doit-devkit-v1)
  • Amazon: https://www.amazon.com/gp/product/B08246MCL5
  • Newer ESP32-S3 boards will likely work. Just check V_SPI pins
    • esp32-s3 - https://www.amazon.com/LuatOS-Development-Bluetooth-Interfaces-Compatible/dp/B0CDX87YX4
      • MACOS - install serial driver https://github.com/WCHSoftGroup/ch34xser_macos
      • platformis board: esp32-s3-devkitc-1

Code inspiration came from the following repos/threads:

• https://github.com/jg-storey/ded
• https://github.com/wiggles5289/Orange-Viper-Simulations/tree/main/F16
• https://forum.dcs.world/topic/261806-f16-ded-with-ssd1322-and-dcs-bios/page/3/

TODO

• write unit tests

Software

Software Build requirements

• platformio - https://platformio.org/install

Software Build Steps

1. Clone this repo

   git clone https://github.com/peterb154/F16-DED.git
   cd F16-DED
   

2. Create/update your wifi settings in src/secrets.h.
   • See an example in src/secrets-example.h
3. build and upload DCS-BIOS WiFi enabled versionto your board

   pio run -e WIFI -t upload && pio device monitor
   

Hardware

ESP32 DevKit v1 HW SPI Wiring

| OLED (Pin)  | Wire * | ESP32 (Pin)    | #define ** |
| ----------- | ------ | -------------- | ---------- |
| VDD (2)     | WHT    | 3v3            |            |
| GND (1)     | BLK    | GND            |            |
| SDIK D1 (5) | PPL    | V_SPI_D (23)   |            |
| SCLK D0 (4) | GRY    | V_SPI_CLK (18) |            |
| CS  (16)    | YEL    | V_SPI_CS0 (5)  | V_SPI_CS0  |
| DC  (14)    | BLU    | GPIO (27)      | SPI_DC     |
| RES (15)    | GRN    | GPIO (26)      | SPI_RESET  |

• Note *: These are my wire colors, yours will likely be different
• Note **: Update #define statements as required in src/main.cpp
• See: https://mischianti.org/wp-content/uploads/2020/11/ESP32-DOIT-DEV-KIT-v1-pinout-mischianti.png for ESP32 dev kit v1 pinout

DED Case

See case/ for stl files. Print at normal 20% infill, no supports. Its a very simple design that requires no fasteners.

Sim configuration

DCS Bios

1. On your DCS machine, Install latest Skunkworks version of DCS-BIOS - https://github.com/DCS-Skunkworks/dcs-bios/releases
   1. You dont need to so the socat steps, we'll use wifi baby
2. On your DCS machchine, Install DCS-Nexus mdns router - https://github.com/DCSBIOSKit/DCS-Nexus
   1. As of 2023-10-28: clone the repo git clone https://github.com/DCSBIOSKit/DCS-Nexus && cd DCS-Nexus
   2. create a virtual environment python -m venv venv
   3. run venv\Scripts\python Nexus.pyw
3. Fly the F16 in DCS and enjoythe DED