Skip to content

Mikrotiks ATtiny based PoE managment/monitoring utility

Notifications You must be signed in to change notification settings

prudy/mtpoe_ctrl

 
 

Repository files navigation

Program for manage the Mikrotiks PoE V2 based on a microcontroller ATtiny 461a

Licence is GNU GPL V3

Examples of using:
	mtpoe_ctrl -dumpvars #shows the values of parameter variables
	mtpoe_ctrl #shows full information about PoE controller state/work
	mtpoe_ctrl --action=get_fw_ver #shows firmware version of the Attiny PoE microcontroller
	mtpoe_ctrl --action=get_voltage #shows the input voltage
	mtpoe_ctrl --action=get_temperature #shows the temperature
	mtpoe_ctrl --action=get_poe #shows the status of PoE for the ports. 0->ether2, 1..2, 3->ether5
	mtpoe_ctrl --action=set_poe --port=0 --val=1 #force-on PoE for port ether2
	mtpoe_ctrl --action=set_poe --port=1 --val=2 #auto-on PoE for port ether3
	mtpoe_ctrl --action=set_poe --port=2 --val=1 #force-on PoE for port ether4
	mtpoe_ctrl --action=set_poe --port=3 --val=0 #turn off PoE for port ether5
	mtpoe_ctrl --action=load_poe_from_uci #load PoE port settings from uci->network->mtik_poe

In /etc/config/network the mtik_poe section should be present:
config mtik_poe
	option port0 '1'
	option port1 '0'
	option port2 '1'
	option port3 '0'

Control is performed by sending commands via SPI bus. The mediator between userspace
and kernel is spidev driver and as a consequence in mach-rb-*.c init file of the platform it is
necessary to write about the following:

/* RB 750-r2(HB) with POE v2 */
#define RB750R2_ATTINY_CS			12
#define RB750R2_ATTINY_RESET	14
static int rb750r2spi_cs_gpios[3] = {
	-ENOENT, /* NOR flash. CS is automatically controlled by the spi controller itself. */
	RB750R2SSR_CS, /* 74x164 gpio extender */
	RB750R2_ATTINY_CS, /* ATtiny PoE v2 */
};
static struct ath79_spi_platform_data rb750r2spi_data __initdata = {
	.bus_num = 0,
	.num_chipselect = 3, /* We have three CS */
	.cs_gpios = rb750r2spi_cs_gpios, /* which CS */
};
static struct spi_board_info rb750r2spi_info[] = {
	...
		.max_speed_hz = 10000000,
		.modalias = "74x164",
		.platform_data = &rb750r2ssr_data,
	}, {
		.bus_num = 0,
		.chip_select = 2,
		.max_speed_hz = 2000000,
		.modalias = "spidev",
  }
}
static void __init rb750r2_setup(void)
{
	...
	ath79_register_spi(&rb750r2spi_data, rb750r2spi_info, ARRAY_SIZE(rb750r2spi_info));
	...
}

or if you use DTS:
&spi {
	spidev@2 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "linux,spidev";
		reg = <2>;
		spi-max-frequency = <2200000>;
	};
};

About

Mikrotiks ATtiny based PoE managment/monitoring utility

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C 94.7%
  • Makefile 5.0%
  • Shell 0.3%