bcm2835-i2s: fix hw_params error when device is in prepared state #2345
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
|
That change looks sensible to me. Are you planning to push this patch upstream? |
|
Yes, just sent out the mail and put you in CC |
|
Cool. I'll wait until I see an Ack before merging, unless it is particularly urgent? |
|
Sure, just wait until we get some more feedback. It's not urgent, that bug has been there forever without anyone noticing it. I tested full duplex mode before, but with bcm2835-i2s in slave mode (where the bug doesn't occur). I also tested with "aplay | arecord" both in slave and master mode, but the bug doesn't occur there either (because hw_params bails out early if a stream is already running so it doesn't hit the problematic code). I became aware of the issue via this forum post https://www.raspberrypi.org/forums/viewtopic.php?p=1254351#p1254351 and also asked the poster to test and report back |
popcornmix
force-pushed
the
rpi-4.14.y
branch
from
bc910e1 to
23816e6
Compare
If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
HiassofT
force-pushed
the
4.14-i2s-clock-fix
branch
from
da2345a to
e2dd6fb
Compare
|
rebased PR on top of current rpi-4.14.y |
That counts as an Ack. |
|
wow, that was really quick! @pelwell could you pick that into the 4.15 tree as well? |
pelwell
pushed a commit
that referenced
this pull request
Jan 18, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
|
It would have been picked up in one of the regular cherry-picks, but it's done now. |
|
Thanks a lot!
|
popcornmix
pushed a commit
that referenced
this pull request
Jan 22, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Jan 25, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Jan 29, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Jan 31, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
TiejunChina
pushed a commit
to TiejunChina/linux
that referenced
this pull request
Feb 2, 2018
…aspberrypi#2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 5, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 5, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 5, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 9, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 12, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 13, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
TiejunChina
pushed a commit
to TiejunChina/linux
that referenced
this pull request
Feb 14, 2018
…aspberrypi#2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 19, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 23, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Feb 26, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 8, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 14, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 16, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 22, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 26, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Mar 29, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Apr 3, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Apr 9, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Apr 16, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
May 5, 2018
…2345) commit 8d5737a upstream. If bcm2835 is configured as bitclock master calling hw_params() after prepare() fails with EBUSY. This also makes it impossible to use bcm2835 in full duplex mode. The error is caused by the split clock setup: clk_set_rate is called in hw_params, clk_prepare_enable in prepare. As hw_params doesn't check if the clock was already enabled clk_set_rate fails with EBUSY. Fix this by moving clock startup from prepare to hw_params and let hw_params properly deal with an already set up or enabled clock. Signed-off-by: Matthias Reichl <hias@horus.com>
popcornmix
pushed a commit
that referenced
this pull request
Jul 21, 2021
…format [ Upstream commit 06d213d ] For incoming SCO connection with transparent coding format, alt setting of CVSD is getting applied instead of Transparent. Before fix: < HCI Command: Accept Synchron.. (0x01|0x0029) plen 21 #2196 [hci0] 321.342548 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #2197 [hci0] 321.343585 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Comp.. (0x2c) plen 17 #2198 [hci0] 321.351666 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) ........ > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2336 [hci0] 321.383655 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2337 [hci0] 321.389558 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2338 [hci0] 321.393615 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2339 [hci0] 321.393618 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2340 [hci0] 321.393618 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2341 [hci0] 321.397070 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2342 [hci0] 321.403622 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2343 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2344 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2345 [hci0] 321.403625 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2346 [hci0] 321.404569 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2347 [hci0] 321.412091 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2348 [hci0] 321.413626 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2349 [hci0] 321.413630 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2350 [hci0] 321.413630 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2351 [hci0] 321.419674 After fix: < HCI Command: Accept Synchronou.. (0x01|0x0029) plen 21 #309 [hci0] 49.439693 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #310 [hci0] 49.440308 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Complete (0x2c) plen 17 #311 [hci0] 49.449308 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) < SCO Data TX: Handle 257 flags 0x00 dlen 60 #312 [hci0] 49.450421 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #313 [hci0] 49.457927 > HCI Event: Max Slots Change (0x1b) plen 3 #314 [hci0] 49.460345 Handle: 256 Max slots: 5 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #315 [hci0] 49.465453 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #316 [hci0] 49.470502 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #317 [hci0] 49.470519 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #318 [hci0] 49.472996 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #319 [hci0] 49.480412 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #320 [hci0] 49.480492 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #321 [hci0] 49.487989 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #322 [hci0] 49.490303 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #323 [hci0] 49.495496 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #324 [hci0] 49.500304 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #325 [hci0] 49.500311 Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Lokendra Singh <lokendra.singh@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
popcornmix
pushed a commit
that referenced
this pull request
Jul 22, 2021
…format [ Upstream commit 06d213d ] For incoming SCO connection with transparent coding format, alt setting of CVSD is getting applied instead of Transparent. Before fix: < HCI Command: Accept Synchron.. (0x01|0x0029) plen 21 #2196 [hci0] 321.342548 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #2197 [hci0] 321.343585 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Comp.. (0x2c) plen 17 #2198 [hci0] 321.351666 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) ........ > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2336 [hci0] 321.383655 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2337 [hci0] 321.389558 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2338 [hci0] 321.393615 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2339 [hci0] 321.393618 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2340 [hci0] 321.393618 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2341 [hci0] 321.397070 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2342 [hci0] 321.403622 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2343 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2344 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2345 [hci0] 321.403625 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2346 [hci0] 321.404569 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2347 [hci0] 321.412091 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2348 [hci0] 321.413626 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2349 [hci0] 321.413630 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2350 [hci0] 321.413630 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2351 [hci0] 321.419674 After fix: < HCI Command: Accept Synchronou.. (0x01|0x0029) plen 21 #309 [hci0] 49.439693 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #310 [hci0] 49.440308 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Complete (0x2c) plen 17 #311 [hci0] 49.449308 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) < SCO Data TX: Handle 257 flags 0x00 dlen 60 #312 [hci0] 49.450421 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #313 [hci0] 49.457927 > HCI Event: Max Slots Change (0x1b) plen 3 #314 [hci0] 49.460345 Handle: 256 Max slots: 5 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #315 [hci0] 49.465453 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #316 [hci0] 49.470502 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #317 [hci0] 49.470519 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #318 [hci0] 49.472996 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #319 [hci0] 49.480412 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #320 [hci0] 49.480492 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #321 [hci0] 49.487989 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #322 [hci0] 49.490303 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #323 [hci0] 49.495496 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #324 [hci0] 49.500304 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #325 [hci0] 49.500311 Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Lokendra Singh <lokendra.singh@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
popcornmix
pushed a commit
that referenced
this pull request
Jul 27, 2021
…format [ Upstream commit 06d213d ] For incoming SCO connection with transparent coding format, alt setting of CVSD is getting applied instead of Transparent. Before fix: < HCI Command: Accept Synchron.. (0x01|0x0029) plen 21 #2196 [hci0] 321.342548 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #2197 [hci0] 321.343585 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Comp.. (0x2c) plen 17 #2198 [hci0] 321.351666 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) ........ > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2336 [hci0] 321.383655 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2337 [hci0] 321.389558 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2338 [hci0] 321.393615 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2339 [hci0] 321.393618 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2340 [hci0] 321.393618 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2341 [hci0] 321.397070 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2342 [hci0] 321.403622 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2343 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2344 [hci0] 321.403625 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2345 [hci0] 321.403625 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2346 [hci0] 321.404569 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2347 [hci0] 321.412091 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2348 [hci0] 321.413626 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2349 [hci0] 321.413630 > SCO Data RX: Handle 257 flags 0x00 dlen 48 #2350 [hci0] 321.413630 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #2351 [hci0] 321.419674 After fix: < HCI Command: Accept Synchronou.. (0x01|0x0029) plen 21 #309 [hci0] 49.439693 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x003f HV1 may be used HV2 may be used HV3 may be used EV3 may be used EV4 may be used EV5 may be used > HCI Event: Command Status (0x0f) plen 4 #310 [hci0] 49.440308 Accept Synchronous Connection Request (0x01|0x0029) ncmd 1 Status: Success (0x00) > HCI Event: Synchronous Connect Complete (0x2c) plen 17 #311 [hci0] 49.449308 Status: Success (0x00) Handle: 257 Address: 1C:CC:D6:E2:EA:80 (Xiaomi Communications Co Ltd) Link type: eSCO (0x02) Transmission interval: 0x0c Retransmission window: 0x04 RX packet length: 60 TX packet length: 60 Air mode: Transparent (0x03) < SCO Data TX: Handle 257 flags 0x00 dlen 60 #312 [hci0] 49.450421 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #313 [hci0] 49.457927 > HCI Event: Max Slots Change (0x1b) plen 3 #314 [hci0] 49.460345 Handle: 256 Max slots: 5 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #315 [hci0] 49.465453 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #316 [hci0] 49.470502 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #317 [hci0] 49.470519 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #318 [hci0] 49.472996 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #319 [hci0] 49.480412 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #320 [hci0] 49.480492 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #321 [hci0] 49.487989 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #322 [hci0] 49.490303 < SCO Data TX: Handle 257 flags 0x00 dlen 60 #323 [hci0] 49.495496 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #324 [hci0] 49.500304 > SCO Data RX: Handle 257 flags 0x00 dlen 60 #325 [hci0] 49.500311 Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Lokendra Singh <lokendra.singh@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
If bcm2835 is configured as bitclock master calling hw_params()
after prepare() fails with EBUSY. This also makes it impossible to
use bcm2835 in full duplex mode.
The error is caused by the split clock setup: clk_set_rate
is called in hw_params, clk_prepare_enable in prepare. As hw_params
doesn't check if the clock was already enabled clk_set_rate
fails with EBUSY.
Fix this by moving clock startup from prepare to hw_params and
let hw_params properly deal with an already set up or enabled
clock.