riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes #1

chainsx · 2023-10-11T16:31:51Z

添加设备树节点后：

板载 8723ds 可用
SD 卡槽仍无法使用

In powerpc pseries system, below behaviour is observed while enabling tracing on hcall: # cd /sys/kernel/debug/tracing/ # cat events/powerpc/hcall_exit/enable 0 # echo 1 > events/powerpc/hcall_exit/enable # ls -bash: fork: Bad address Above is from power9 lpar with latest kernel. Past this, softlockup is observed. Initially while attempting via perf_event_open to use "PERF_TYPE_TRACEPOINT", kernel panic was observed. perf config used: ================ memset(&pe[1],0,sizeof(struct perf_event_attr)); pe[1].type=PERF_TYPE_TRACEPOINT; pe[1].size=96; pe[1].config=0x26ULL; /* 38 raw_syscalls/sys_exit */ pe[1].sample_type=0; /* 0 */ pe[1].read_format=PERF_FORMAT_TOTAL_TIME_ENABLED|PERF_FORMAT_TOTAL_TIME_RUNNING|PERF_FORMAT_ID|PERF_FORMAT_GROUP|0x10ULL; /* 1f */ pe[1].inherit=1; pe[1].precise_ip=0; /* arbitrary skid */ pe[1].wakeup_events=0; pe[1].bp_type=HW_BREAKPOINT_EMPTY; pe[1].config1=0x1ULL; Kernel panic logs: ================== Kernel attempted to read user page (8) - exploit attempt? (uid: 0) BUG: Kernel NULL pointer dereference on read at 0x00000008 Faulting instruction address: 0xc0000000004c2814 Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries Modules linked in: nfnetlink bonding tls rfkill sunrpc dm_service_time dm_multipath pseries_rng xts vmx_crypto xfs libcrc32c sd_mod t10_pi crc64_rocksoft crc64 sg ibmvfc scsi_transport_fc ibmveth dm_mirror dm_region_hash dm_log dm_mod fuse CPU: 0 PID: 1431 Comm: login Not tainted 6.4.0+ #1 Hardware name: IBM,8375-42A POWER9 (raw) 0x4e0202 0xf000005 of:IBM,FW950.30 (VL950_892) hv:phyp pSeries NIP page_remove_rmap+0x44/0x320 LR wp_page_copy+0x384/0xec0 Call Trace: 0xc00000001416e400 (unreliable) wp_page_copy+0x384/0xec0 __handle_mm_fault+0x9d4/0xfb0 handle_mm_fault+0xf0/0x350 ___do_page_fault+0x48c/0xc90 hash__do_page_fault+0x30/0x70 do_hash_fault+0x1a4/0x330 data_access_common_virt+0x198/0x1f0 --- interrupt: 300 at 0x7fffae971abc git bisect tracked this down to below commit: 'commit baa49d8 ("powerpc/pseries: hvcall stack frame overhead")' This commit changed STACK_FRAME_OVERHEAD (112 ) to STACK_FRAME_MIN_SIZE (32 ) since 32 bytes is the minimum size for ELFv2 stack. With the latest kernel, when running on ELFv2, STACK_FRAME_MIN_SIZE is used to allocate stack size. During plpar_hcall_trace, first call is made to HCALL_INST_PRECALL which saves the registers and allocates new stack frame. In the plpar_hcall_trace code, STK_PARAM is accessed at two places. 1. To save r4: std r4,STK_PARAM(R4)(r1) 2. To access r4 back: ld r12,STK_PARAM(R4)(r1) HCALL_INST_PRECALL precall allocates a new stack frame. So all the stack parameter access after the precall, needs to be accessed with +STACK_FRAME_MIN_SIZE. So the store instruction should be: std r4,STACK_FRAME_MIN_SIZE+STK_PARAM(R4)(r1) If the "std" is not updated with STACK_FRAME_MIN_SIZE, we will end up with overwriting stack contents and cause corruption. But instead of updating 'std', we can instead remove it since HCALL_INST_PRECALL already saves it to the correct location. similarly load instruction should be: ld r12,STACK_FRAME_MIN_SIZE+STK_PARAM(R4)(r1) Fix the load instruction to correctly access the stack parameter with +STACK_FRAME_MIN_SIZE and remove the store of r4 since the precall saves it correctly. Cc: stable@vger.kernel.org # v6.2+ Fixes: baa49d8 ("powerpc/pseries: hvcall stack frame overhead") Co-developed-by: Naveen N Rao <naveen@kernel.org> Signed-off-by: Naveen N Rao <naveen@kernel.org> Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230929172337.7906-1-atrajeev@linux.vnet.ibm.com

Many functions in drivers/usb/core/hub.c and drivers/usb/core/hub.h access fields inside udev->bos without checking if it was allocated and initialized. If usb_get_bos_descriptor() fails for whatever reason, udev->bos will be NULL and those accesses will result in a crash: BUG: kernel NULL pointer dereference, address: 0000000000000018 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 5 PID: 17818 Comm: kworker/5:1 Tainted: G W 5.15.108-18910-gab0e1cb584e1 #1 <HASH:1f9e 1> Hardware name: Google Kindred/Kindred, BIOS Google_Kindred.12672.413.0 02/03/2021 Workqueue: usb_hub_wq hub_event RIP: 0010:hub_port_reset+0x193/0x788 Code: 89 f7 e8 20 f7 15 00 48 8b 43 08 80 b8 96 03 00 00 03 75 36 0f b7 88 92 03 00 00 81 f9 10 03 00 00 72 27 48 8b 80 a8 03 00 00 <48> 83 78 18 00 74 19 48 89 df 48 8b 75 b0 ba 02 00 00 00 4c 89 e9 RSP: 0018:ffffab740c53fcf8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa1bc5f678000 RCX: 0000000000000310 RDX: fffffffffffffdff RSI: 0000000000000286 RDI: ffffa1be9655b840 RBP: ffffab740c53fd70 R08: 00001b7d5edaa20c R09: ffffffffb005e060 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000 R13: ffffab740c53fd3e R14: 0000000000000032 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffa1be96540000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000022e80c005 CR4: 00000000003706e0 Call Trace: hub_event+0x73f/0x156e ? hub_activate+0x5b7/0x68f process_one_work+0x1a2/0x487 worker_thread+0x11a/0x288 kthread+0x13a/0x152 ? process_one_work+0x487/0x487 ? kthread_associate_blkcg+0x70/0x70 ret_from_fork+0x1f/0x30 Fall back to a default behavior if the BOS descriptor isn't accessible and skip all the functionalities that depend on it: LPM support checks, Super Speed capabilitiy checks, U1/U2 states setup. Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20230830100418.1952143-1-ricardo.canuelo@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For ARM processor, unaligned access to device memory is not allowed. Method memcpy does not take care of alignment. USB detection failure with the unalingned address of memory, with below kernel crash. To fix the unalingned address kernel panic, replace memcpy with memcpy_toio method. Kernel crash: Unable to handle kernel paging request at virtual address ffff80000c05008a Mem abort info: ESR = 0x96000061 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x21: alignment fault Data abort info: ISV = 0, ISS = 0x00000061 CM = 0, WnR = 1 swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000 [ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003, pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713 Internal error: Oops: 96000061 [#1] SMP Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1 Hardware name: ZynqMP ZCU102 Rev1.0 (DT) pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __memcpy+0x30/0x260 lr : __xudc_ep0_queue+0xf0/0x110 sp : ffff800008003d00 x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0 x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080 x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080 x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000 x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000 x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200 x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0 x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112 x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80 x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088 Call trace: __memcpy+0x30/0x260 xudc_ep0_queue+0x3c/0x60 usb_ep_queue+0x38/0x44 composite_ep0_queue.constprop.0+0x2c/0xc0 composite_setup+0x8d0/0x185c configfs_composite_setup+0x74/0xb0 xudc_irq+0x570/0xa40 __handle_irq_event_percpu+0x58/0x170 handle_irq_event+0x60/0x120 handle_fasteoi_irq+0xc0/0x220 handle_domain_irq+0x60/0x90 gic_handle_irq+0x74/0xa0 call_on_irq_stack+0x2c/0x60 do_interrupt_handler+0x54/0x60 el1_interrupt+0x30/0x50 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x78/0x7c arch_cpu_idle+0x18/0x2c do_idle+0xdc/0x15c cpu_startup_entry+0x28/0x60 rest_init+0xc8/0xe0 arch_call_rest_init+0x10/0x1c start_kernel+0x694/0x6d4 __primary_switched+0xa4/0xac Fixes: 1f7c516 ("usb: gadget: Add xilinx usb2 device support") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/all/202209020044.CX2PfZzM-lkp@intel.com/ Cc: stable@vger.kernel.org Signed-off-by: Piyush Mehta <piyush.mehta@amd.com> Link: https://lore.kernel.org/r/20230929121514.13475-1-piyush.mehta@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Surfaces can be backed (i.e. stored in) memory objects (mob's) which are created and managed by the userspace as GEM buffers. Surfaces grab only a ttm reference which means that the gem object can be deleted underneath us, especially in cases where prime buffer export is used. Make sure that all userspace surfaces which are backed by gem objects hold a gem reference to make sure they're not deleted before vmw surfaces are done with them, which fixes: ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 2 PID: 2632 at lib/refcount.c:28 refcount_warn_saturate+0xfb/0x150 Modules linked in: overlay vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vsock snd_ens1371 snd_ac97_codec ac97_bus snd_pcm gameport> CPU: 2 PID: 2632 Comm: vmw_ref_count Not tainted 6.5.0-rc2-vmwgfx #1 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 RIP: 0010:refcount_warn_saturate+0xfb/0x150 Code: eb 9e 0f b6 1d 8b 5b a6 01 80 fb 01 0f 87 ba e4 80 00 83 e3 01 75 89 48 c7 c7 c0 3c f9 a3 c6 05 6f 5b a6 01 01 e8 15 81 98 ff <0f> 0b e9 6f ff ff ff 0f b> RSP: 0018:ffffbdc34344bba0 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000027 RDX: ffff960475ea1548 RSI: 0000000000000001 RDI: ffff960475ea1540 RBP: ffffbdc34344bba8 R08: 0000000000000003 R09: 65646e75203a745f R10: ffffffffa5b32b20 R11: 72657466612d6573 R12: ffff96037d6a6400 R13: ffff9603484805b0 R14: 000000000000000b R15: ffff9603bed06060 FS: 00007f5fd8520c40(0000) GS:ffff960475e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5fda755000 CR3: 000000010d012005 CR4: 00000000003706e0 Call Trace: <TASK> ? show_regs+0x6e/0x80 ? refcount_warn_saturate+0xfb/0x150 ? __warn+0x91/0x150 ? refcount_warn_saturate+0xfb/0x150 ? report_bug+0x19d/0x1b0 ? handle_bug+0x46/0x80 ? exc_invalid_op+0x1d/0x80 ? asm_exc_invalid_op+0x1f/0x30 ? refcount_warn_saturate+0xfb/0x150 drm_gem_object_handle_put_unlocked+0xba/0x110 [drm] drm_gem_object_release_handle+0x6e/0x80 [drm] drm_gem_handle_delete+0x6a/0xc0 [drm] ? __pfx_vmw_bo_unref_ioctl+0x10/0x10 [vmwgfx] vmw_bo_unref_ioctl+0x33/0x40 [vmwgfx] drm_ioctl_kernel+0xbc/0x160 [drm] drm_ioctl+0x2d2/0x580 [drm] ? __pfx_vmw_bo_unref_ioctl+0x10/0x10 [vmwgfx] ? do_vmi_munmap+0xee/0x180 vmw_generic_ioctl+0xbd/0x180 [vmwgfx] vmw_unlocked_ioctl+0x19/0x20 [vmwgfx] __x64_sys_ioctl+0x99/0xd0 do_syscall_64+0x5d/0x90 ? syscall_exit_to_user_mode+0x2a/0x50 ? do_syscall_64+0x6d/0x90 ? handle_mm_fault+0x16e/0x2f0 ? exit_to_user_mode_prepare+0x34/0x170 ? irqentry_exit_to_user_mode+0xd/0x20 ? irqentry_exit+0x3f/0x50 ? exc_page_fault+0x8e/0x190 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 RIP: 0033:0x7f5fda51aaff Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <41> 89 c0 3d 00 f0 ff ff 7> RSP: 002b:00007ffd536a4d30 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffd536a4de0 RCX: 00007f5fda51aaff RDX: 00007ffd536a4de0 RSI: 0000000040086442 RDI: 0000000000000003 RBP: 0000000040086442 R08: 000055fa603ada50 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000246 R12: 00007ffd536a51b8 R13: 0000000000000003 R14: 000055fa5ebb4c80 R15: 00007f5fda90f040 </TASK> ---[ end trace 0000000000000000 ]--- A lot of the analyis on the bug was done by Murray McAllister and Ian Forbes. Reported-by: Murray McAllister <murray.mcallister@gmail.com> Cc: Ian Forbes <iforbes@vmware.com> Signed-off-by: Zack Rusin <zackr@vmware.com> Fixes: a950b98 ("drm/vmwgfx: Do not drop the reference to the handle too soon") Cc: <stable@vger.kernel.org> # v6.2+ Reviewed-by: Martin Krastev <krastevm@vmware.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230928041355.737635-1-zack@kde.org

Eddie reported that newer kernels were crashing during boot on his 476 FSP2 system: kernel tried to execute user page (b7ee2000) - exploit attempt? (uid: 0) BUG: Unable to handle kernel instruction fetch Faulting instruction address: 0xb7ee2000 Oops: Kernel access of bad area, sig: 11 [#1] BE PAGE_SIZE=4K FSP-2 Modules linked in: CPU: 0 PID: 61 Comm: mount Not tainted 6.1.55-d23900f.ppcnf-fsp2 #1 Hardware name: ibm,fsp2 476fpe 0x7ff520c0 FSP-2 NIP: b7ee2000 LR: 8c008000 CTR: 00000000 REGS: bffebd83 TRAP: 0400 Not tainted (6.1.55-d23900f.ppcnf-fs p2) MSR: 00000030 <IR,DR> CR: 00001000 XER: 20000000 GPR00: c00110ac bffebe63 bffebe7e bffebe88 8c008000 00001000 00000d12 b7ee2000 GPR08: 00000033 00000000 00000000 c139df10 48224824 1016c314 10160000 00000000 GPR16: 10160000 10160000 00000008 00000000 10160000 00000000 10160000 1017f5b0 GPR24: 1017fa50 1017f4f0 1017fa50 1017f740 1017f630 00000000 00000000 1017f4f0 NIP [b7ee2000] 0xb7ee2000 LR [8c008000] 0x8c008000 Call Trace: Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace 0000000000000000 ]--- The problem is in ret_from_syscall where the check for icache_44x_need_flush is done. When the flush is needed the code jumps out-of-line to do the flush, and then intends to jump back to continue the syscall return. However the branch back to label 1b doesn't return to the correct location, instead branching back just prior to the return to userspace, causing bogus register values to be used by the rfi. The breakage was introduced by commit 6f76a01 ("powerpc/syscall: implement system call entry/exit logic in C for PPC32") which inadvertently removed the "1" label and reused it elsewhere. Fix it by adding named local labels in the correct locations. Note that the return label needs to be outside the ifdef so that CONFIG_PPC_47x=n compiles. Fixes: 6f76a01 ("powerpc/syscall: implement system call entry/exit logic in C for PPC32") Cc: stable@vger.kernel.org # v5.12+ Reported-by: Eddie James <eajames@linux.ibm.com> Tested-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/linuxppc-dev/fdaadc46-7476-9237-e104-1d2168526e72@linux.ibm.com/ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Link: https://msgid.link/20231010114750.847794-1-mpe@ellerman.id.au

When testing on risc-v QEMU environment with "crashkernel=" parameter enabled, a problem occurred with the following message: [ 0.000000] crashkernel low memory reserved: 0xf8000000 - 0x100000000 (128 MB) [ 0.000000] crashkernel reserved: 0x0000000177e00000 - 0x0000000277e00000 (4096 MB) [ 0.000000] ------------[ cut here ]------------ [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/resource.c:779 __insert_resource+0x8e/0xd0 [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.6.0-rc2-next-20230920 #1 [ 0.000000] Hardware name: riscv-virtio,qemu (DT) [ 0.000000] epc : __insert_resource+0x8e/0xd0 [ 0.000000] ra : insert_resource+0x28/0x4e [ 0.000000] epc : ffffffff80017344 ra : ffffffff8001742e sp : ffffffff81203db0 [ 0.000000] gp : ffffffff812ece98 tp : ffffffff8120dac0 t0 : ff600001f7ff2b00 [ 0.000000] t1 : 0000000000000000 t2 : 3428203030303030 s0 : ffffffff81203dc0 [ 0.000000] s1 : ffffffff81211e18 a0 : ffffffff81211e18 a1 : ffffffff81289380 [ 0.000000] a2 : 0000000277dfffff a3 : 0000000177e00000 a4 : 0000000177e00000 [ 0.000000] a5 : ffffffff81289380 a6 : 0000000277dfffff a7 : 0000000000000078 [ 0.000000] s2 : ffffffff81289380 s3 : ffffffff80a0bac8 s4 : ff600001f7ff2880 [ 0.000000] s5 : 0000000000000280 s6 : 8000000a00006800 s7 : 000000000000007f [ 0.000000] s8 : 0000000080017038 s9 : 0000000080038ea0 s10: 0000000000000000 [ 0.000000] s11: 0000000000000000 t3 : ffffffff80a0bc00 t4 : ffffffff80a0bc00 [ 0.000000] t5 : ffffffff80a0bbd0 t6 : ffffffff80a0bc00 [ 0.000000] status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003 [ 0.000000] [<ffffffff80017344>] __insert_resource+0x8e/0xd0 [ 0.000000] ---[ end trace 0000000000000000 ]--- [ 0.000000] Failed to add a Crash kernel resource at 177e00000 The crashkernel memory has been allocated successfully, whereas it failed to insert into iomem_resource. This is due to the unique reserving logic in risc-v arch specific code, i.e. crashk_res/crashk_low_res will be added into iomem_resource later in init_resources(), which is not aligned with current unified reserving logic in reserve_crashkernel_{generic,low}() and therefore leads to the failure of crashkernel reservation. Removing the arch specific code within #ifdef CONFIG_KEXEC_CORE in init_resources() to fix above problem. Fixes: 3154915 ("riscv: kdump: use generic interface to simplify crashkernel reservation") Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com> Link: https://lore.kernel.org/r/20230925024333.730964-1-chenjiahao16@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

A GISA cannot be destroyed as long it is linked in the GIB alert list as this would break the alert list. Just waiting for its removal from the list triggered by another vm is not sufficient as it might be the only vm. The below shown cpu stall situation might occur when GIB alerts are delayed and is fixed by calling process_gib_alert_list() instead of waiting. At this time the vcpus of the vm are already destroyed and thus no vcpu can be kicked to enter the SIE again if for some reason an interrupt is pending for that vm. Additionally the IAM restore value is set to 0x00. That would be a bug introduced by incomplete device de-registration, i.e. missing kvm_s390_gisc_unregister() call. Setting this value and the IAM in the GISA to 0x00 guarantees that late interrupts don't bring the GISA back into the alert list. CPU stall caused by kvm_s390_gisa_destroy(): [ 4915.311372] rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 14-.... } 24533 jiffies s: 5269 root: 0x1/. [ 4915.311390] rcu: blocking rcu_node structures (internal RCU debug): l=1:0-15:0x4000/. [ 4915.311394] Task dump for CPU 14: [ 4915.311395] task:qemu-system-s39 state:R running task stack:0 pid:217198 ppid:1 flags:0x00000045 [ 4915.311399] Call Trace: [ 4915.311401] [<0000038003a33a10>] 0x38003a33a10 [ 4933.861321] rcu: INFO: rcu_sched self-detected stall on CPU [ 4933.861332] rcu: 14-....: (42008 ticks this GP) idle=53f4/1/0x4000000000000000 softirq=61530/61530 fqs=14031 [ 4933.861353] rcu: (t=42008 jiffies g=238109 q=100360 ncpus=18) [ 4933.861357] CPU: 14 PID: 217198 Comm: qemu-system-s39 Not tainted 6.5.0-20230816.rc6.git26.a9d17c5d8813.300.fc38.s390x #1 [ 4933.861360] Hardware name: IBM 8561 T01 703 (LPAR) [ 4933.861361] Krnl PSW : 0704e00180000000 000003ff804bfc66 (kvm_s390_gisa_destroy+0x3e/0xe0 [kvm]) [ 4933.861414] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3 [ 4933.861416] Krnl GPRS: 0000000000000000 00000372000000fc 00000002134f8000 000000000d5f5900 [ 4933.861419] 00000002f5ea1d18 00000002f5ea1d18 0000000000000000 0000000000000000 [ 4933.861420] 00000002134fa890 00000002134f8958 000000000d5f5900 00000002134f8000 [ 4933.861422] 000003ffa06acf98 000003ffa06858b0 0000038003a33c20 0000038003a33bc8 [ 4933.861430] Krnl Code: 000003ff804bfc58: ec66002b007e cij %r6,0,6,000003ff804bfcae 000003ff804bfc5e: b904003a lgr %r3,%r10 #000003ff804bfc62: a7f40005 brc 15,000003ff804bfc6c >000003ff804bfc66: e330b7300204 lg %r3,10032(%r11) 000003ff804bfc6c: 58003000 l %r0,0(%r3) 000003ff804bfc70: ec03fffb6076 crj %r0,%r3,6,000003ff804bfc66 000003ff804bfc76: e320b7600271 lay %r2,10080(%r11) 000003ff804bfc7c: c0e5fffea339 brasl %r14,000003ff804942ee [ 4933.861444] Call Trace: [ 4933.861445] [<000003ff804bfc66>] kvm_s390_gisa_destroy+0x3e/0xe0 [kvm] [ 4933.861460] ([<00000002623523de>] free_unref_page+0xee/0x148) [ 4933.861507] [<000003ff804aea98>] kvm_arch_destroy_vm+0x50/0x120 [kvm] [ 4933.861521] [<000003ff8049d374>] kvm_destroy_vm+0x174/0x288 [kvm] [ 4933.861532] [<000003ff8049d4fe>] kvm_vm_release+0x36/0x48 [kvm] [ 4933.861542] [<00000002623cd04a>] __fput+0xea/0x2a8 [ 4933.861547] [<00000002620d5bf8>] task_work_run+0x88/0xf0 [ 4933.861551] [<00000002620b0aa6>] do_exit+0x2c6/0x528 [ 4933.861556] [<00000002620b0f00>] do_group_exit+0x40/0xb8 [ 4933.861557] [<00000002620b0fa6>] __s390x_sys_exit_group+0x2e/0x30 [ 4933.861559] [<0000000262d481f4>] __do_syscall+0x1d4/0x200 [ 4933.861563] [<0000000262d59028>] system_call+0x70/0x98 [ 4933.861565] Last Breaking-Event-Address: [ 4933.861566] [<0000038003a33b60>] 0x38003a33b60 Fixes: 9f30f62 ("KVM: s390: add gib_alert_irq_handler()") Signed-off-by: Michael Mueller <mimu@linux.ibm.com> Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Nico Boehr <nrb@linux.ibm.com> Link: https://lore.kernel.org/r/20230901105823.3973928-1-mimu@linux.ibm.com Message-ID: <20230901105823.3973928-1-mimu@linux.ibm.com> Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>

Use atomic readl_poll_timeout_atomic, because msdc_reset_hw may be invoked in IRQ handler in the following context: msdc_irq() -> msdc_cmd_done() -> msdc_reset_hw() The following kernel BUG stack trace can be observed on Genio 1200 EVK after initializing MSDC1 hardware during kernel boot: [ 1.187441] BUG: scheduling while atomic: swapper/0/0/0x00010002 [ 1.189157] Modules linked in: [ 1.204633] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.15.42-mtk+modified #1 [ 1.205713] Hardware name: MediaTek Genio 1200 EVK-P1V2-EMMC (DT) [ 1.206484] Call trace: [ 1.206796] dump_backtrace+0x0/0x1ac [ 1.207266] show_stack+0x24/0x30 [ 1.207692] dump_stack_lvl+0x68/0x84 [ 1.208162] dump_stack+0x1c/0x38 [ 1.208587] __schedule_bug+0x68/0x80 [ 1.209056] __schedule+0x6ec/0x7c0 [ 1.209502] schedule+0x7c/0x110 [ 1.209915] schedule_hrtimeout_range_clock+0xc4/0x1f0 [ 1.210569] schedule_hrtimeout_range+0x20/0x30 [ 1.211148] usleep_range_state+0x84/0xc0 [ 1.211661] msdc_reset_hw+0xc8/0x1b0 [ 1.212134] msdc_cmd_done.isra.0+0x4ac/0x5f0 [ 1.212693] msdc_irq+0x104/0x2d4 [ 1.213121] __handle_irq_event_percpu+0x68/0x280 [ 1.213725] handle_irq_event+0x70/0x15c [ 1.214230] handle_fasteoi_irq+0xb0/0x1a4 [ 1.214755] handle_domain_irq+0x6c/0x9c [ 1.215260] gic_handle_irq+0xc4/0x180 [ 1.215741] call_on_irq_stack+0x2c/0x54 [ 1.216245] do_interrupt_handler+0x5c/0x70 [ 1.216782] el1_interrupt+0x30/0x80 [ 1.217242] el1h_64_irq_handler+0x1c/0x2c [ 1.217769] el1h_64_irq+0x78/0x7c [ 1.218206] cpuidle_enter_state+0xc8/0x600 [ 1.218744] cpuidle_enter+0x44/0x5c [ 1.219205] do_idle+0x224/0x2d0 [ 1.219624] cpu_startup_entry+0x30/0x80 [ 1.220129] rest_init+0x108/0x134 [ 1.220568] arch_call_rest_init+0x1c/0x28 [ 1.221094] start_kernel+0x6c0/0x700 [ 1.221564] __primary_switched+0xc0/0xc8 Fixes: ffaea6e ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling") Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioachino.delregno@collabora.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230922095348.22182-1-pablo.sun@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The cited patch change mlx5 driver so that during probe DMA operations were performed before pci_enable_device(), and during teardown DMA operations were performed after pci_disable_device(). DMA operations require PCI to be enabled. Hence, The above leads to the following oops in PPC systems[1]. On s390x systems, as reported by Niklas Schnelle, this is a problem because mlx5_pci_init() is where the DMA and coherent mask is set but mlx5_cmd_init() already does a dma_alloc_coherent(). Thus a DMA allocation is done during probe before the correct mask is set. This causes probe to fail initialization of the cmdif SW structs on s390x after that is converted to the common dma-iommu code. This is because on s390x DMA addresses below 4 GiB are reserved on current machines and unlike the old s390x specific DMA API implementation common code enforces DMA masks. Fix it by performing the DMA operations during probe after pci_enable_device() and after the dma mask is set, and during teardown before pci_disable_device(). [1] Oops: Kernel access of bad area, sig: 11 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink xfrm_user iptable_nat xt_addrtype xt_conntrack nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 netconsole rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser ib_umad rdma_cm ib_ipoib iw_cm libiscsi scsi_transport_iscsi ib_cm ib_uverbs ib_core mlx5_core(-) ptp pps_core fuse vmx_crypto crc32c_vpmsum [last unloaded: mlx5_ib] CPU: 1 PID: 8937 Comm: modprobe Not tainted 6.5.0-rc3_for_upstream_min_debug_2023_07_31_16_02 #1 Hardware name: IBM pSeries (emulated by qemu) POWER9 (raw) 0x4e1202 0xf000005 of:SLOF,HEAD hv:linux,kvm pSeries NIP: c000000000423388 LR: c0000000001e733c CTR: c0000000001e4720 REGS: c0000000055636d0 TRAP: 0380 Not tainted (6.5.0-rc3_for_upstream_min_debug_2023_07_31_16_02) MSR: 8000000000009033 CR: 24008884 XER: 20040000 CFAR: c0000000001e7338 IRQMASK: 0 NIP [c000000000423388] __free_pages+0x28/0x160 LR [c0000000001e733c] dma_direct_free+0xac/0x190 Call Trace: [c000000005563970] [5deadbeef0000100] 0x5deadbeef0000100 (unreliable) [c0000000055639b0] [c0000000003d46cc] kfree+0x7c/0x150 [c000000005563a40] [c0000000001e47c8] dma_free_attrs+0xa8/0x1a0 [c000000005563aa0] [c008000000d0064c] mlx5_cmd_cleanup+0xa4/0x100 [mlx5_core] [c000000005563ad0] [c008000000cf629c] mlx5_mdev_uninit+0xf4/0x140 [mlx5_core] [c000000005563b00] [c008000000cf6448] remove_one+0x160/0x1d0 [mlx5_core] [c000000005563b40] [c000000000958540] pci_device_remove+0x60/0x110 [c000000005563b80] [c000000000a35e80] device_remove+0x70/0xd0 [c000000005563bb0] [c000000000a37a38] device_release_driver_internal+0x2a8/0x330 [c000000005563c00] [c000000000a37b8c] driver_detach+0x8c/0x160 [c000000005563c40] [c000000000a35350] bus_remove_driver+0x90/0x110 [c000000005563c80] [c000000000a38948] driver_unregister+0x48/0x90 [c000000005563cf0] [c000000000957e38] pci_unregister_driver+0x38/0x150 [c000000005563d40] [c008000000eb6140] mlx5_cleanup+0x38/0x90 [mlx5_core] Fixes: 06cd555 ("net/mlx5: split mlx5_cmd_init() to probe and reload routines") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com> Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Hold RTNL lock when calling xdp_set_features() with a registered netdev, as the call triggers the netdev notifiers. This could happen when switching from nic profile to uplink representor for example. Similar logic which fixed a similar scenario was previously introduced in the following commit: commit 72cc654 net/mlx5e: Take RTNL lock when needed before calling xdp_set_features(). This fixes the following assertion and warning call trace: RTNL: assertion failed at net/core/dev.c (1961) WARNING: CPU: 13 PID: 2529 at net/core/dev.c:1961 call_netdevice_notifiers_info+0x7c/0x80 Modules linked in: rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_core zram zsmalloc fuse CPU: 13 PID: 2529 Comm: devlink Not tainted 6.5.0_for_upstream_min_debug_2023_09_07_20_04 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:call_netdevice_notifiers_info+0x7c/0x80 Code: 8f ff 80 3d 77 0d 16 01 00 75 c5 ba a9 07 00 00 48 c7 c6 c4 bb 0d 82 48 c7 c7 18 c8 06 82 c6 05 5b 0d 16 01 01 e8 44 f6 8c ff <0f> 0b eb a2 0f 1f 44 00 00 55 48 89 e5 41 54 48 83 e4 f0 48 83 ec RSP: 0018:ffff88819930f7f0 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffff8309f740 RCX: 0000000000000027 RDX: ffff88885fb5b5c8 RSI: 0000000000000001 RDI: ffff88885fb5b5c0 RBP: 0000000000000028 R08: ffff88887ffabaa8 R09: 0000000000000003 R10: ffff88887fecbac0 R11: ffff88887ff7bac0 R12: ffff88819930f810 R13: ffff88810b7fea40 R14: ffff8881154e8fd8 R15: ffff888107e881a0 FS: 00007f3ad248f800(0000) GS:ffff88885fb40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000563b85f164e0 CR3: 0000000113b5c006 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn+0x79/0x120 ? call_netdevice_notifiers_info+0x7c/0x80 ? report_bug+0x17c/0x190 ? handle_bug+0x3c/0x60 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? call_netdevice_notifiers_info+0x7c/0x80 call_netdevice_notifiers+0x2e/0x50 mlx5e_set_xdp_feature+0x21/0x50 [mlx5_core] mlx5e_build_rep_params+0x97/0x130 [mlx5_core] mlx5e_init_ul_rep+0x9f/0x100 [mlx5_core] mlx5e_netdev_init_profile+0x76/0x110 [mlx5_core] mlx5e_netdev_attach_profile+0x1f/0x90 [mlx5_core] mlx5e_netdev_change_profile+0x92/0x160 [mlx5_core] mlx5e_vport_rep_load+0x329/0x4a0 [mlx5_core] mlx5_esw_offloads_rep_load+0x9e/0xf0 [mlx5_core] esw_offloads_enable+0x4bc/0xe90 [mlx5_core] mlx5_eswitch_enable_locked+0x3c8/0x570 [mlx5_core] ? kmalloc_trace+0x25/0x80 mlx5_devlink_eswitch_mode_set+0x224/0x680 [mlx5_core] ? devlink_get_from_attrs_lock+0x9e/0x110 devlink_nl_cmd_eswitch_set_doit+0x60/0xe0 genl_family_rcv_msg_doit+0xd0/0x120 genl_rcv_msg+0x180/0x2b0 ? devlink_get_from_attrs_lock+0x110/0x110 ? devlink_nl_cmd_eswitch_get_doit+0x290/0x290 ? devlink_pernet_pre_exit+0xf0/0xf0 ? genl_family_rcv_msg_dumpit+0xf0/0xf0 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x1fc/0x2c0 netlink_sendmsg+0x232/0x4a0 sock_sendmsg+0x38/0x60 ? _copy_from_user+0x2a/0x60 __sys_sendto+0x110/0x160 ? handle_mm_fault+0x161/0x260 ? do_user_addr_fault+0x276/0x620 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7f3ad231340a Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 RSP: 002b:00007ffd70aad4b8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000c36b00 RCX:00007f3ad231340a RDX: 0000000000000038 RSI: 0000000000c36b00 RDI: 0000000000000003 RBP: 0000000000c36910 R08: 00007f3ad2625200 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000001 </TASK> ---[ end trace 0000000000000000 ]--- ------------[ cut here ]------------ Fixes: 4d5ab0a ("net/mlx5e: take into account device reconfiguration for xdp_features flag") Signed-off-by: Lama Kayal <lkayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

On driver load, scsi_add_host() can fail. This triggers the free path to call qla2x00_mem_free() multiple times. This causes NULL pointer access of ha->base_qpair. Add check before access. BUG: unable to handle kernel NULL pointer dereference at 0000000000000030 IP: [<ffffffffc118f73c>] qla2x00_mem_free+0x51c/0xcb0 [qla2xxx] PGD 8000001fcfe4a067 PUD 1fc8f0a067 PMD 0 Oops: 0000 [#1] SMP RIP: 0010:[<ffffffffc118f73c>] [<ffffffffc118f73c>] qla2x00_mem_free+0x51c/0xcb0 [qla2xxx] RSP: 0018:ffff8ace97a93a30 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8ace8efd0000 RCX: 000000000000488f RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff8ace97a93a60 R08: 000000000001f040 R09: ffffffff8678209b R10: ffff8acf7d6df040 R11: ffffc591c0fcc980 R12: ffffffff87034800 R13: ffff8acf0e3cc740 R14: ffff8ace8efd0000 R15: 00000000fffffff4 FS: 00007f4cf5449740(0000) GS:ffff8acf7d6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000030 CR3: 0000001fc2f6c000 CR4: 00000000007607e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: [<ffffffff86781f18>] ? kobject_put+0x28/0x60 [<ffffffffc119a59c>] qla2x00_probe_one+0x19fc/0x3040 [qla2xxx] Fixes: efeda3b ("scsi: qla2xxx: Move resource to allow code reuse") Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20231016101749.5059-1-njavali@marvell.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

…ress If we specify a valid CQ ring address but an invalid SQ ring address, we'll correctly spot this and free the allocated pages and clear them to NULL. However, we don't clear the ring page count, and hence will attempt to free the pages again. We've already cleared the address of the page array when freeing them, but we don't check for that. This causes the following crash: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Oops [#1] Modules linked in: CPU: 0 PID: 20 Comm: kworker/u2:1 Not tainted 6.6.0-rc5-dirty torvalds#56 Hardware name: ucbbar,riscvemu-bare (DT) Workqueue: events_unbound io_ring_exit_work epc : io_pages_free+0x2a/0x58 ra : io_rings_free+0x3a/0x50 epc : ffffffff808811a2 ra : ffffffff80881406 sp : ffff8f80000c3cd0 status: 0000000200000121 badaddr: 0000000000000000 cause: 000000000000000d [<ffffffff808811a2>] io_pages_free+0x2a/0x58 [<ffffffff80881406>] io_rings_free+0x3a/0x50 [<ffffffff80882176>] io_ring_exit_work+0x37e/0x424 [<ffffffff80027234>] process_one_work+0x10c/0x1f4 [<ffffffff8002756e>] worker_thread+0x252/0x31c [<ffffffff8002f5e4>] kthread+0xc4/0xe0 [<ffffffff8000332a>] ret_from_fork+0xa/0x1c Check for a NULL array in io_pages_free(), but also clear the page counts when we free them to be on the safer side. Reported-by: rtm@csail.mit.edu Fixes: 03d89a2 ("io_uring: support for user allocated memory for rings/sqes") Cc: stable@vger.kernel.org Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>

when the checked address is illegal,the corresponding shadow address from kasan_mem_to_shadow may have no mapping in mmu table. Access such shadow address causes kernel oops. Here is a sample about oops on arm64(VA 39bit) with KASAN_SW_TAGS and KASAN_OUTLINE on: [ffffffb80aaaaaaa] pgd=000000005d3ce003, p4d=000000005d3ce003, pud=000000005d3ce003, pmd=0000000000000000 Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP Modules linked in: CPU: 3 PID: 100 Comm: sh Not tainted 6.6.0-rc1-dirty torvalds#43 Hardware name: linux,dummy-virt (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __hwasan_load8_noabort+0x5c/0x90 lr : do_ib_ob+0xf4/0x110 ffffffb80aaaaaaa is the shadow address for efffff80aaaaaaaa. The problem is reading invalid shadow in kasan_check_range. The generic kasan also has similar oops. It only reports the shadow address which causes oops but not the original address. Commit 2f004ee("x86/kasan: Print original address on #GP") introduce to kasan_non_canonical_hook but limit it to KASAN_INLINE. This patch extends it to KASAN_OUTLINE mode. Link: https://lkml.kernel.org/r/20231009073748.159228-1-haibo.li@mediatek.com Fixes: 2f004ee("x86/kasan: Print original address on #GP") Signed-off-by: Haibo Li <haibo.li@mediatek.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Haibo Li <haibo.li@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

As drm_dp_get_mst_branch_device_by_guid() is called from drm_dp_get_mst_branch_device_by_guid(), mstb parameter has to be checked, otherwise NULL dereference may occur in the call to the memcpy() and cause following: [12579.365869] BUG: kernel NULL pointer dereference, address: 0000000000000049 [12579.365878] #PF: supervisor read access in kernel mode [12579.365880] #PF: error_code(0x0000) - not-present page [12579.365882] PGD 0 P4D 0 [12579.365887] Oops: 0000 [#1] PREEMPT SMP NOPTI ... [12579.365895] Workqueue: events_long drm_dp_mst_up_req_work [12579.365899] RIP: 0010:memcmp+0xb/0x29 [12579.365921] Call Trace: [12579.365927] get_mst_branch_device_by_guid_helper+0x22/0x64 [12579.365930] drm_dp_mst_up_req_work+0x137/0x416 [12579.365933] process_one_work+0x1d0/0x419 [12579.365935] worker_thread+0x11a/0x289 [12579.365938] kthread+0x13e/0x14f [12579.365941] ? process_one_work+0x419/0x419 [12579.365943] ? kthread_blkcg+0x31/0x31 [12579.365946] ret_from_fork+0x1f/0x30 As get_mst_branch_device_by_guid_helper() is recursive, moving condition to the first line allow to remove a similar one for step over of NULL elements inside a loop. Fixes: 5e93b82 ("drm/dp/mst: move GUID storage from mgr, port to only mst branch") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Lukasz Majczak <lma@semihalf.com> Reviewed-by: Radoslaw Biernacki <rad@chromium.org> Signed-off-by: Manasi Navare <navaremanasi@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230922063410.23626-1-lma@semihalf.com

Erhard reported that his G5 was crashing with v6.6-rc kernels: mpic: Setting up HT PICs workarounds for U3/U4 BUG: Unable to handle kernel data access at 0xfeffbb62ffec65fe Faulting instruction address: 0xc00000000005dc40 Oops: Kernel access of bad area, sig: 11 [#1] BE PAGE_SIZE=4K MMU=Hash SMP NR_CPUS=2 PowerMac Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Tainted: G T 6.6.0-rc3-PMacGS #1 Hardware name: PowerMac11,2 PPC970MP 0x440101 PowerMac NIP: c00000000005dc40 LR: c000000000066660 CTR: c000000000007730 REGS: c0000000022bf510 TRAP: 0380 Tainted: G T (6.6.0-rc3-PMacGS) MSR: 9000000000001032 <SF,HV,ME,IR,DR,RI> CR: 44004242 XER: 00000000 IRQMASK: 3 GPR00: 0000000000000000 c0000000022bf7b0 c0000000010c0b00 00000000000001ac GPR04: 0000000003c80000 0000000000000300 c0000000f20001ae 0000000000000300 GPR08: 0000000000000006 feffbb62ffec65ff 0000000000000001 0000000000000000 GPR12: 9000000000001032 c000000002362000 c000000000f76b80 000000000349ecd8 GPR16: 0000000002367ba8 0000000002367f08 0000000000000006 0000000000000000 GPR20: 00000000000001ac c000000000f6f920 c0000000022cd985 000000000000000c GPR24: 0000000000000300 00000003b0a3691d c0003e008030000e 0000000000000000 GPR28: c00000000000000c c0000000f20001ee feffbb62ffec65fe 00000000000001ac NIP hash_page_do_lazy_icache+0x50/0x100 LR __hash_page_4K+0x420/0x590 Call Trace: hash_page_mm+0x364/0x6f0 do_hash_fault+0x114/0x2b0 data_access_common_virt+0x198/0x1f0 --- interrupt: 300 at mpic_init+0x4bc/0x10c4 NIP: c000000002020a5c LR: c000000002020a04 CTR: 0000000000000000 REGS: c0000000022bf9f0 TRAP: 0300 Tainted: G T (6.6.0-rc3-PMacGS) MSR: 9000000000001032 <SF,HV,ME,IR,DR,RI> CR: 24004248 XER: 00000000 DAR: c0003e008030000e DSISR: 40000000 IRQMASK: 1 ... NIP mpic_init+0x4bc/0x10c4 LR mpic_init+0x464/0x10c4 --- interrupt: 300 pmac_setup_one_mpic+0x258/0x2dc pmac_pic_init+0x28c/0x3d8 init_IRQ+0x90/0x140 start_kernel+0x57c/0x78c start_here_common+0x1c/0x20 A bisect pointed to the breakage beginning with commit 9fee28b ("powerpc: implement the new page table range API"). Analysis of the oops pointed to a struct page with a corrupted compound_head being loaded via page_folio() -> _compound_head() in hash_page_do_lazy_icache(). The access by the mpic code is to an MMIO address, so the expectation is that the struct page for that address would be initialised by init_unavailable_range(), as pointed out by Aneesh. Instrumentation showed that was not the case, which eventually lead to the realisation that pfn_valid() was returning false for that address, causing the struct page to not be initialised. Because the system is using FLATMEM, the version of pfn_valid() in memory_model.h is used: static inline int pfn_valid(unsigned long pfn) { ... return pfn >= pfn_offset && (pfn - pfn_offset) < max_mapnr; } Which relies on max_mapnr being initialised. Early in boot max_mapnr is zero meaning no PFNs are valid. max_mapnr is initialised in mem_init() called via: start_kernel() mm_core_init() # init/main.c:928 mem_init() But that is too late for the usage in init_unavailable_range() called via: start_kernel() setup_arch() # init/main.c:893 paging_init() free_area_init() init_unavailable_range() Although max_mapnr is currently set in mem_init(), the value is actually already available much earlier, as soon as mem_topology_setup() has completed, which is also before paging_init() is called. So move the initialisation there, which causes paging_init() to correctly initialise the struct page and fixes the bug. This bug seems to have been lurking for years, but went unnoticed because the pre-folio code was inspecting the uninitialised page->flags but not dereferencing it. Thanks to Erhard and Aneesh for help debugging. Reported-by: Erhard Furtner <erhard_f@mailbox.org> Closes: https://lore.kernel.org/all/20230929132750.3cd98452@yea/ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20231023112500.1550208-1-mpe@ellerman.id.au

commit bb32500 upstream The following can crash the kernel: # cd /sys/kernel/tracing # echo 'p:sched schedule' > kprobe_events # exec 5>>events/kprobes/sched/enable # > kprobe_events # exec 5>&- The above commands: 1. Change directory to the tracefs directory 2. Create a kprobe event (doesn't matter what one) 3. Open bash file descriptor 5 on the enable file of the kprobe event 4. Delete the kprobe event (removes the files too) 5. Close the bash file descriptor 5 The above causes a crash! BUG: kernel NULL pointer dereference, address: 0000000000000028 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 6 PID: 877 Comm: bash Not tainted 6.5.0-rc4-test-00008-g2c6b6b1029d4-dirty torvalds#186 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:tracing_release_file_tr+0xc/0x50 What happens here is that the kprobe event creates a trace_event_file "file" descriptor that represents the file in tracefs to the event. It maintains state of the event (is it enabled for the given instance?). Opening the "enable" file gets a reference to the event "file" descriptor via the open file descriptor. When the kprobe event is deleted, the file is also deleted from the tracefs system which also frees the event "file" descriptor. But as the tracefs file is still opened by user space, it will not be totally removed until the final dput() is called on it. But this is not true with the event "file" descriptor that is already freed. If the user does a write to or simply closes the file descriptor it will reference the event "file" descriptor that was just freed, causing a use-after-free bug. To solve this, add a ref count to the event "file" descriptor as well as a new flag called "FREED". The "file" will not be freed until the last reference is released. But the FREE flag will be set when the event is removed to prevent any more modifications to that event from happening, even if there's still a reference to the event "file" descriptor. Link: https://lore.kernel.org/linux-trace-kernel/20231031000031.1e705592@gandalf.local.home/ Link: https://lore.kernel.org/linux-trace-kernel/20231031122453.7a48b923@gandalf.local.home Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Fixes: f5ca233 ("tracing: Increase trace array ref count on enable and filter files") Reported-by: Beau Belgrave <beaub@linux.microsoft.com> Tested-by: Beau Belgrave <beaub@linux.microsoft.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4a8e65b ] SRCU callbacks acceleration might fail if the preceding callbacks advance also fails. This can happen when the following steps are met: 1) The RCU_WAIT_TAIL segment has callbacks (say for gp_num 8) and the RCU_NEXT_READY_TAIL also has callbacks (say for gp_num 12). 2) The grace period for RCU_WAIT_TAIL is observed as started but not yet completed so rcu_seq_current() returns 4 + SRCU_STATE_SCAN1 = 5. 3) This value is passed to rcu_segcblist_advance() which can't move any segment forward and fails. 4) srcu_gp_start_if_needed() still proceeds with callback acceleration. But then the call to rcu_seq_snap() observes the grace period for the RCU_WAIT_TAIL segment (gp_num 8) as completed and the subsequent one for the RCU_NEXT_READY_TAIL segment as started (ie: 8 + SRCU_STATE_SCAN1 = 9) so it returns a snapshot of the next grace period, which is 16. 5) The value of 16 is passed to rcu_segcblist_accelerate() but the freshly enqueued callback in RCU_NEXT_TAIL can't move to RCU_NEXT_READY_TAIL which already has callbacks for a previous grace period (gp_num = 12). So acceleration fails. 6) Note in all these steps, srcu_invoke_callbacks() hadn't had a chance to run srcu_invoke_callbacks(). Then some very bad outcome may happen if the following happens: 7) Some other CPU races and starts the grace period number 16 before the CPU handling previous steps had a chance. Therefore srcu_gp_start() isn't called on the latter sdp to fix the acceleration leak from previous steps with a new pair of call to advance/accelerate. 8) The grace period 16 completes and srcu_invoke_callbacks() is finally called. All the callbacks from previous grace periods (8 and 12) are correctly advanced and executed but callbacks in RCU_NEXT_READY_TAIL still remain. Then rcu_segcblist_accelerate() is called with a snaphot of 20. 9) Since nothing started the grace period number 20, callbacks stay unhandled. This has been reported in real load: [3144162.608392] INFO: task kworker/136:12:252684 blocked for more than 122 seconds. [3144162.615986] Tainted: G O K 5.4.203-1-tlinux4-0011.1 #1 [3144162.623053] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [3144162.631162] kworker/136:12 D 0 252684 2 0x90004000 [3144162.631189] Workqueue: kvm-irqfd-cleanup irqfd_shutdown [kvm] [3144162.631192] Call Trace: [3144162.631202] __schedule+0x2ee/0x660 [3144162.631206] schedule+0x33/0xa0 [3144162.631209] schedule_timeout+0x1c4/0x340 [3144162.631214] ? update_load_avg+0x82/0x660 [3144162.631217] ? raw_spin_rq_lock_nested+0x1f/0x30 [3144162.631218] wait_for_completion+0x119/0x180 [3144162.631220] ? wake_up_q+0x80/0x80 [3144162.631224] __synchronize_srcu.part.19+0x81/0xb0 [3144162.631226] ? __bpf_trace_rcu_utilization+0x10/0x10 [3144162.631227] synchronize_srcu+0x5f/0xc0 [3144162.631236] irqfd_shutdown+0x3c/0xb0 [kvm] [3144162.631239] ? __schedule+0x2f6/0x660 [3144162.631243] process_one_work+0x19a/0x3a0 [3144162.631244] worker_thread+0x37/0x3a0 [3144162.631247] kthread+0x117/0x140 [3144162.631247] ? process_one_work+0x3a0/0x3a0 [3144162.631248] ? __kthread_cancel_work+0x40/0x40 [3144162.631250] ret_from_fork+0x1f/0x30 Fix this with taking the snapshot for acceleration _before_ the read of the current grace period number. The only side effect of this solution is that callbacks advancing happen then _after_ the full barrier in rcu_seq_snap(). This is not a problem because that barrier only cares about: 1) Ordering accesses of the update side before call_srcu() so they don't bleed. 2) See all the accesses prior to the grace period of the current gp_num The only things callbacks advancing need to be ordered against are carried by snp locking. Reported-by: Yong He <alexyonghe@tencent.com> Co-developed-by:: Yong He <alexyonghe@tencent.com> Signed-off-by: Yong He <alexyonghe@tencent.com> Co-developed-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Co-developed-by: Neeraj upadhyay <Neeraj.Upadhyay@amd.com> Signed-off-by: Neeraj upadhyay <Neeraj.Upadhyay@amd.com> Link: http://lore.kernel.org/CANZk6aR+CqZaqmMWrC2eRRPY12qAZnDZLwLnHZbNi=xXMB401g@mail.gmail.com Fixes: da915ad ("srcu: Parallelize callback handling") Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d5252d9 ] The clock dividers might be used with clock stop bit enabled or not. Current tables only support recommended values from the datasheet. This might result in warnings like below because no valid clock divider is found. Resulting in a 0 divider. There are Renesas ARM Trusted Firmware version out there which e.g. configure 0x201 (shifted logical right by 2: 0x80) and with this match the added { STPnHCK | 0, 1 }: https://github.com/renesas-rcar/arm-trusted-firmware/blob/rcar_gen3_v2.3/drivers/renesas/rcar/emmc/emmc_init.c#L108 ------------[ cut here ]------------ sd1h: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set WARNING: CPU: 1 PID: 1 at drivers/clk/clk-divider.c:141 divider_recalc_rate+0x48/0x70 Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.52 #1 Hardware name: Custom board based on r8a7796 (DT) pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : divider_recalc_rate+0x48/0x70 ... ------------[ cut here ]------------ Fixes: bb6d3fa ("clk: renesas: rcar-gen3: Switch to new SD clock handling") Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> [wsa: extended the table to 5 entries, added comments, reword commit message a little] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Dirk Behme <dirk.behme@de.bosch.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230928080317.28224-1-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4428399 ] The lt8912b driver, in its bridge detach function, calls drm_connector_unregister() and drm_connector_cleanup(). drm_connector_unregister() should be called only for connectors explicitly registered with drm_connector_register(), which is not the case in lt8912b. The driver's drm_connector_funcs.destroy hook is set to drm_connector_cleanup(). Thus the driver should not call either drm_connector_unregister() nor drm_connector_cleanup() in its lt8912_bridge_detach(), as they cause a crash on bridge detach: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000006 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault Data abort info: ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=00000000858f3000 [0000000000000000] pgd=0800000085918003, p4d=0800000085918003, pud=0800000085431003, pmd=0000000000000000 Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP Modules linked in: tidss(-) display_connector lontium_lt8912b tc358768 panel_lvds panel_simple drm_dma_helper drm_kms_helper drm drm_panel_orientation_quirks CPU: 3 PID: 462 Comm: rmmod Tainted: G W 6.5.0-rc2+ #2 Hardware name: Toradex Verdin AM62 on Verdin Development Board (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : drm_connector_cleanup+0x78/0x2d4 [drm] lr : lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] sp : ffff800082ed3a90 x29: ffff800082ed3a90 x28: ffff0000040c1940 x27: 0000000000000000 x26: 0000000000000000 x25: dead000000000122 x24: dead000000000122 x23: dead000000000100 x22: ffff000003fb6388 x21: 0000000000000000 x20: 0000000000000000 x19: ffff000003fb6260 x18: fffffffffffe56e8 x17: 0000000000000000 x16: 0010000000000000 x15: 0000000000000038 x14: 0000000000000000 x13: ffff800081914b48 x12: 000000000000040e x11: 000000000000015a x10: ffff80008196ebb8 x9 : ffff800081914b48 x8 : 00000000ffffefff x7 : ffff0000040c1940 x6 : ffff80007aa649d0 x5 : 0000000000000000 x4 : 0000000000000001 x3 : ffff80008159e008 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: drm_connector_cleanup+0x78/0x2d4 [drm] lt8912_bridge_detach+0x54/0x6c [lontium_lt8912b] drm_bridge_detach+0x44/0x84 [drm] drm_encoder_cleanup+0x40/0xb8 [drm] drmm_encoder_alloc_release+0x1c/0x30 [drm] drm_managed_release+0xac/0x148 [drm] drm_dev_put.part.0+0x88/0xb8 [drm] devm_drm_dev_init_release+0x14/0x24 [drm] devm_action_release+0x14/0x20 release_nodes+0x5c/0x90 devres_release_all+0x8c/0xe0 device_unbind_cleanup+0x18/0x68 device_release_driver_internal+0x208/0x23c driver_detach+0x4c/0x94 bus_remove_driver+0x70/0xf4 driver_unregister+0x30/0x60 platform_driver_unregister+0x14/0x20 tidss_platform_driver_exit+0x18/0xb2c [tidss] __arm64_sys_delete_module+0x1a0/0x2b4 invoke_syscall+0x48/0x110 el0_svc_common.constprop.0+0x60/0x10c do_el0_svc_compat+0x1c/0x40 el0_svc_compat+0x40/0xac el0t_32_sync_handler+0xb0/0x138 el0t_32_sync+0x194/0x198 Code: 9104a276 f2fbd5b7 aa0203e1 91008af8 (f85c0420) Fixes: 30e2ae9 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge") Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230804-lt8912b-v1-2-c542692c6a2f@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>

…i_hns3_pmu uninit process [ Upstream commit 50b5607 ] When tearing down a 'hisi_hns3' PMU, we mistakenly run the CPU hotplug callbacks after the device has been unregistered, leading to fireworks when we try to execute empty function callbacks within the driver: | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 | CPU: 0 PID: 15 Comm: cpuhp/0 Tainted: G W O 5.12.0-rc4+ #1 | Hardware name: , BIOS KpxxxFPGA 1P B600 V143 04/22/2021 | pstate: 80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--) | pc : perf_pmu_migrate_context+0x98/0x38c | lr : perf_pmu_migrate_context+0x94/0x38c | | Call trace: | perf_pmu_migrate_context+0x98/0x38c | hisi_hns3_pmu_offline_cpu+0x104/0x12c [hisi_hns3_pmu] Use cpuhp_state_remove_instance_nocalls() instead of cpuhp_state_remove_instance() so that the notifiers don't execute after the PMU device has been unregistered. Fixes: 66637ab ("drivers/perf: hisi: add driver for HNS3 PMU") Signed-off-by: Hao Chen <chenhao418@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Yicong Yang <yangyicong@hisilicon.com> Link: https://lore.kernel.org/r/20231019091352.998964-1-shaojijie@huawei.com [will: Rewrote commit message] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

…it_event_hooks() [ Upstream commit 91cfe0b ] When CONFIG_HID_UCLOGIC=y and CONFIG_KUNIT_ALL_TESTS=y, launch kernel and then the below user-memory-access bug occurs. In hid_test_uclogic_params_cleanup_event_hooks(),it call uclogic_params_ugee_v2_init_event_hooks() with the first arg=NULL, so when it calls uclogic_params_ugee_v2_has_battery(), the hid_get_drvdata() will access hdev->dev with hdev=NULL, which will cause below user-memory-access. So add a fake_device with quirks member and call hid_set_drvdata() to assign hdev->dev->driver_data which avoids the null-ptr-def bug for drvdata->quirks in uclogic_params_ugee_v2_has_battery(). After applying this patch, the below user-memory-access bug never occurs. general protection fault, probably for non-canonical address 0xdffffc0000000329: 0000 [#1] PREEMPT SMP KASAN KASAN: probably user-memory-access in range [0x0000000000001948-0x000000000000194f] CPU: 5 PID: 2189 Comm: kunit_try_catch Tainted: G B W N 6.6.0-rc2+ torvalds#30 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ffffffff8fdd6cf5 DR2: ffffffff8fdd6cf6 DR3: ffffffff8fdd6cf7 DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 ? sched_clock_cpu+0x69/0x550 ? uclogic_parse_ugee_v2_desc_gen_params+0x70/0x70 ? load_balance+0x2950/0x2950 ? rcu_trc_cmpxchg_need_qs+0x67/0xa0 hid_test_uclogic_params_cleanup_event_hooks+0x9e/0x1a0 ? uclogic_params_ugee_v2_init_event_hooks+0x600/0x600 ? __switch_to+0x5cf/0xe60 ? migrate_enable+0x260/0x260 ? __kthread_parkme+0x83/0x150 ? kunit_try_run_case_cleanup+0xe0/0xe0 kunit_generic_run_threadfn_adapter+0x4a/0x90 ? kunit_try_catch_throw+0x80/0x80 kthread+0x2b5/0x380 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x2d/0x70 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork_asm+0x11/0x20 </TASK> Modules linked in: Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 0000000000000000 ]--- RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ffffffff8fdd6cf5 DR2: ffffffff8fdd6cf6 DR3: ffffffff8fdd6cf7 DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Kernel panic - not syncing: Fatal exception Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Rebooting in 1 seconds.. Fixes: a251d65 ("HID: uclogic: Handle wireless device reconnection") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Reviewed-by: José Expósito <jose.exposito89@gmail.com> Link: https://lore.kernel.org/r/20231009064245.3573397-2-ruanjinjie@huawei.com Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a84fbf2 ] Generating metrics llc_code_read_mpi_demand_plus_prefetch, llc_data_read_mpi_demand_plus_prefetch, llc_miss_local_memory_bandwidth_read, llc_miss_local_memory_bandwidth_write, nllc_miss_remote_memory_bandwidth_read, memory_bandwidth_read, memory_bandwidth_write, uncore_frequency, upi_data_transmit_bw, C2_Pkg_Residency, C3_Core_Residency, C3_Pkg_Residency, C6_Core_Residency, C6_Pkg_Residency, C7_Core_Residency, C7_Pkg_Residency, UNCORE_FREQ and tma_info_system_socket_clks would trigger an address sanitizer heap-buffer-overflows on a SkylakeX. ``` ==2567752==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x5020003ed098 at pc 0x5621a816654e bp 0x7fffb55d4da0 sp 0x7fffb55d4d98 READ of size 4 at 0x5020003eee78 thread T0 #0 0x558265d6654d in aggr_cpu_id__is_empty tools/perf/util/cpumap.c:694:12 #1 0x558265c914da in perf_stat__get_aggr tools/perf/builtin-stat.c:1490:6 #2 0x558265c914da in perf_stat__get_global_cached tools/perf/builtin-stat.c:1530:9 #3 0x558265e53290 in should_skip_zero_counter tools/perf/util/stat-display.c:947:31 #4 0x558265e53290 in print_counter_aggrdata tools/perf/util/stat-display.c:985:18 #5 0x558265e51931 in print_counter tools/perf/util/stat-display.c:1110:3 #6 0x558265e51931 in evlist__print_counters tools/perf/util/stat-display.c:1571:5 #7 0x558265c8ec87 in print_counters tools/perf/builtin-stat.c:981:2 #8 0x558265c8cc71 in cmd_stat tools/perf/builtin-stat.c:2837:3 #9 0x558265bb9bd4 in run_builtin tools/perf/perf.c:323:11 #10 0x558265bb98eb in handle_internal_command tools/perf/perf.c:377:8 #11 0x558265bb9389 in run_argv tools/perf/perf.c:421:2 #12 0x558265bb9389 in main tools/perf/perf.c:537:3 ``` The issue was the use of testing a cpumap with NULL rather than using empty, as a map containing the dummy value isn't NULL and the -1 results in an empty aggr map being allocated which legitimately overflows when any member is accessed. Fixes: 8a96f45 ("perf stat: Avoid SEGV if core.cpus isn't set") Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20230906003912.3317462-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ede72dc ] Fuzzing found that an invalid tracepoint name would create a memory leak with an address sanitizer build: ``` $ perf stat -e '*:o/' true event syntax error: '*:o/' \___ parser error Run 'perf list' for a list of valid events Usage: perf stat [<options>] [<command>] -e, --event <event> event selector. use 'perf list' to list available events ================================================================= ==59380==ERROR: LeakSanitizer: detected memory leaks Direct leak of 4 byte(s) in 2 object(s) allocated from: #0 0x7f38ac07077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439 #1 0x55f2f41be73b in str util/parse-events.l:49 #2 0x55f2f41d08e8 in parse_events_lex util/parse-events.l:338 #3 0x55f2f41dc3b1 in parse_events_parse util/parse-events-bison.c:1464 #4 0x55f2f410b8b3 in parse_events__scanner util/parse-events.c:1822 #5 0x55f2f410d1b9 in __parse_events util/parse-events.c:2094 #6 0x55f2f410e57f in parse_events_option util/parse-events.c:2279 #7 0x55f2f4427b56 in get_value tools/lib/subcmd/parse-options.c:251 #8 0x55f2f4428d98 in parse_short_opt tools/lib/subcmd/parse-options.c:351 #9 0x55f2f4429d80 in parse_options_step tools/lib/subcmd/parse-options.c:539 #10 0x55f2f442acb9 in parse_options_subcommand tools/lib/subcmd/parse-options.c:654 #11 0x55f2f3ec99fc in cmd_stat tools/perf/builtin-stat.c:2501 #12 0x55f2f4093289 in run_builtin tools/perf/perf.c:322 #13 0x55f2f40937f5 in handle_internal_command tools/perf/perf.c:375 #14 0x55f2f4093bbd in run_argv tools/perf/perf.c:419 torvalds#15 0x55f2f409412b in main tools/perf/perf.c:535 SUMMARY: AddressSanitizer: 4 byte(s) leaked in 2 allocation(s). ``` Fix by adding the missing destructor. Fixes: 865582c ("perf tools: Adds the tracepoint name parsing support") Signed-off-by: Ian Rogers <irogers@google.com> Cc: He Kuang <hekuang@huawei.com> Link: https://lore.kernel.org/r/20230914164028.363220-1-irogers@google.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 265f3ed ] All callers of work_on_cpu() share the same lock class key for all the functions queued. As a result the workqueue related locking scenario for a function A may be spuriously accounted as an inversion against the locking scenario of function B such as in the following model: long A(void *arg) { mutex_lock(&mutex); mutex_unlock(&mutex); } long B(void *arg) { } void launchA(void) { work_on_cpu(0, A, NULL); } void launchB(void) { mutex_lock(&mutex); work_on_cpu(1, B, NULL); mutex_unlock(&mutex); } launchA and launchB running concurrently have no chance to deadlock. However the above can be reported by lockdep as a possible locking inversion because the works containing A() and B() are treated as belonging to the same locking class. The following shows an existing example of such a spurious lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 6.6.0-rc1-00065-g934ebd6e5359 #35409 Not tainted ------------------------------------------------------ kworker/0:1/9 is trying to acquire lock: ffffffff9bc72f30 (cpu_hotplug_lock){++++}-{0:0}, at: _cpu_down+0x57/0x2b0 but task is already holding lock: ffff9e3bc0057e60 ((work_completion)(&wfc.work)){+.+.}-{0:0}, at: process_scheduled_works+0x216/0x500 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 ((work_completion)(&wfc.work)){+.+.}-{0:0}: __flush_work+0x83/0x4e0 work_on_cpu+0x97/0xc0 rcu_nocb_cpu_offload+0x62/0xb0 rcu_nocb_toggle+0xd0/0x1d0 kthread+0xe6/0x120 ret_from_fork+0x2f/0x40 ret_from_fork_asm+0x1b/0x30 -> #1 (rcu_state.barrier_mutex){+.+.}-{3:3}: __mutex_lock+0x81/0xc80 rcu_nocb_cpu_deoffload+0x38/0xb0 rcu_nocb_toggle+0x144/0x1d0 kthread+0xe6/0x120 ret_from_fork+0x2f/0x40 ret_from_fork_asm+0x1b/0x30 -> #0 (cpu_hotplug_lock){++++}-{0:0}: __lock_acquire+0x1538/0x2500 lock_acquire+0xbf/0x2a0 percpu_down_write+0x31/0x200 _cpu_down+0x57/0x2b0 __cpu_down_maps_locked+0x10/0x20 work_for_cpu_fn+0x15/0x20 process_scheduled_works+0x2a7/0x500 worker_thread+0x173/0x330 kthread+0xe6/0x120 ret_from_fork+0x2f/0x40 ret_from_fork_asm+0x1b/0x30 other info that might help us debug this: Chain exists of: cpu_hotplug_lock --> rcu_state.barrier_mutex --> (work_completion)(&wfc.work) Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((work_completion)(&wfc.work)); lock(rcu_state.barrier_mutex); lock((work_completion)(&wfc.work)); lock(cpu_hotplug_lock); *** DEADLOCK *** 2 locks held by kworker/0:1/9: #0: ffff900481068b38 ((wq_completion)events){+.+.}-{0:0}, at: process_scheduled_works+0x212/0x500 #1: ffff9e3bc0057e60 ((work_completion)(&wfc.work)){+.+.}-{0:0}, at: process_scheduled_works+0x216/0x500 stack backtrace: CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.6.0-rc1-00065-g934ebd6e5359 #35409 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 Workqueue: events work_for_cpu_fn Call Trace: rcu-torture: rcu_torture_read_exit: Start of episode <TASK> dump_stack_lvl+0x4a/0x80 check_noncircular+0x132/0x150 __lock_acquire+0x1538/0x2500 lock_acquire+0xbf/0x2a0 ? _cpu_down+0x57/0x2b0 percpu_down_write+0x31/0x200 ? _cpu_down+0x57/0x2b0 _cpu_down+0x57/0x2b0 __cpu_down_maps_locked+0x10/0x20 work_for_cpu_fn+0x15/0x20 process_scheduled_works+0x2a7/0x500 worker_thread+0x173/0x330 ? __pfx_worker_thread+0x10/0x10 kthread+0xe6/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2f/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK Fix this with providing one lock class key per work_on_cpu() caller. Reported-and-tested-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 170c75d ] As talked about in commit d66d24a ("ath10k: Keep track of which interrupts fired, don't poll them"), if we access the copy engine register at a bad time then ath10k can go boom. However, it's not necessarily easy to know when it's safe to access them. The ChromeOS test labs saw a crash that looked like this at shutdown/reboot time (on a chromeos-5.15 kernel, but likely the problem could also reproduce upstream): Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP ... CPU: 4 PID: 6168 Comm: reboot Not tainted 5.15.111-lockdep-19350-g1d624fe6758f #1 010b9b233ab055c27c6dc88efb0be2f4e9e86f51 Hardware name: Google Kingoftown (DT) ... pc : ath10k_snoc_read32+0x50/0x74 [ath10k_snoc] lr : ath10k_snoc_read32+0x24/0x74 [ath10k_snoc] ... Call trace: ath10k_snoc_read32+0x50/0x74 [ath10k_snoc ...] ath10k_ce_disable_interrupt+0x190/0x65c [ath10k_core ...] ath10k_ce_disable_interrupts+0x8c/0x120 [ath10k_core ...] ath10k_snoc_hif_stop+0x78/0x660 [ath10k_snoc ...] ath10k_core_stop+0x13c/0x1ec [ath10k_core ...] ath10k_halt+0x398/0x5b0 [ath10k_core ...] ath10k_stop+0xfc/0x1a8 [ath10k_core ...] drv_stop+0x148/0x6b4 [mac80211 ...] ieee80211_stop_device+0x70/0x80 [mac80211 ...] ieee80211_do_stop+0x10d8/0x15b0 [mac80211 ...] ieee80211_stop+0x144/0x1a0 [mac80211 ...] __dev_close_many+0x1e8/0x2c0 dev_close_many+0x198/0x33c dev_close+0x140/0x210 cfg80211_shutdown_all_interfaces+0xc8/0x1e0 [cfg80211 ...] ieee80211_remove_interfaces+0x118/0x5c4 [mac80211 ...] ieee80211_unregister_hw+0x64/0x1f4 [mac80211 ...] ath10k_mac_unregister+0x4c/0xf0 [ath10k_core ...] ath10k_core_unregister+0x80/0xb0 [ath10k_core ...] ath10k_snoc_free_resources+0xb8/0x1ec [ath10k_snoc ...] ath10k_snoc_shutdown+0x98/0xd0 [ath10k_snoc ...] platform_shutdown+0x7c/0xa0 device_shutdown+0x3e0/0x58c kernel_restart_prepare+0x68/0xa0 kernel_restart+0x28/0x7c Though there's no known way to reproduce the problem, it makes sense that it would be the same issue where we're trying to access copy engine registers when it's not allowed. Let's fix this by changing how we "disable" the interrupts. Instead of tweaking the copy engine registers we'll just use disable_irq() and enable_irq(). Then we'll configure the interrupts once at power up time. Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1 Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230630151842.1.If764ede23c4e09a43a842771c2ddf99608f25f8e@changeid Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 624820f ] fix crash because of null pointers [ 6104.969662] BUG: kernel NULL pointer dereference, address: 00000000000000c8 [ 6104.969667] #PF: supervisor read access in kernel mode [ 6104.969668] #PF: error_code(0x0000) - not-present page [ 6104.969670] PGD 0 P4D 0 [ 6104.969673] Oops: 0000 [#1] SMP NOPTI [ 6104.969684] RIP: 0010:btusb_mtk_hci_wmt_sync+0x144/0x220 [btusb] [ 6104.969688] RSP: 0018:ffffb8d681533d48 EFLAGS: 00010246 [ 6104.969689] RAX: 0000000000000000 RBX: ffff8ad560bb2000 RCX: 0000000000000006 [ 6104.969691] RDX: 0000000000000000 RSI: ffffb8d681533d08 RDI: 0000000000000000 [ 6104.969692] RBP: ffffb8d681533d70 R08: 0000000000000001 R09: 0000000000000001 [ 6104.969694] R10: 0000000000000001 R11: 00000000fa83b2da R12: ffff8ad461d1d7c0 [ 6104.969695] R13: 0000000000000000 R14: ffff8ad459618c18 R15: ffffb8d681533d90 [ 6104.969697] FS: 00007f5a1cab9d40(0000) GS:ffff8ad578200000(0000) knlGS:00000 [ 6104.969699] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 6104.969700] CR2: 00000000000000c8 CR3: 000000018620c001 CR4: 0000000000760ef0 [ 6104.969701] PKRU: 55555554 [ 6104.969702] Call Trace: [ 6104.969708] btusb_mtk_shutdown+0x44/0x80 [btusb] [ 6104.969732] hci_dev_do_close+0x470/0x5c0 [bluetooth] [ 6104.969748] hci_rfkill_set_block+0x56/0xa0 [bluetooth] [ 6104.969753] rfkill_set_block+0x92/0x160 [ 6104.969755] rfkill_fop_write+0x136/0x1e0 [ 6104.969759] __vfs_write+0x18/0x40 [ 6104.969761] vfs_write+0xdf/0x1c0 [ 6104.969763] ksys_write+0xb1/0xe0 [ 6104.969765] __x64_sys_write+0x1a/0x20 [ 6104.969769] do_syscall_64+0x51/0x180 [ 6104.969771] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 6104.969773] RIP: 0033:0x7f5a21f18fef [ 6104.9] RSP: 002b:00007ffeefe39010 EFLAGS: 00000293 ORIG_RAX: 0000000000000001 [ 6104.969780] RAX: ffffffffffffffda RBX: 000055c10a7560a0 RCX: 00007f5a21f18fef [ 6104.969781] RDX: 0000000000000008 RSI: 00007ffeefe39060 RDI: 0000000000000012 [ 6104.969782] RBP: 00007ffeefe39060 R08: 0000000000000000 R09: 0000000000000017 [ 6104.969784] R10: 00007ffeefe38d97 R11: 0000000000000293 R12: 0000000000000002 [ 6104.969785] R13: 00007ffeefe39220 R14: 00007ffeefe391a0 R15: 000055c10a72acf0 Signed-off-by: youwan Wang <wangyouwan@126.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5104fdf ] In certain types of chips, such as VEGA20, reading the amdgpu_regs_smc file could result in an abnormal null pointer access when the smc_rreg pointer is NULL. Below are the steps to reproduce this issue and the corresponding exception log: 1. Navigate to the directory: /sys/kernel/debug/dri/0 2. Execute command: cat amdgpu_regs_smc 3. Exception Log:: [4005007.702554] BUG: kernel NULL pointer dereference, address: 0000000000000000 [4005007.702562] #PF: supervisor instruction fetch in kernel mode [4005007.702567] #PF: error_code(0x0010) - not-present page [4005007.702570] PGD 0 P4D 0 [4005007.702576] Oops: 0010 [#1] SMP NOPTI [4005007.702581] CPU: 4 PID: 62563 Comm: cat Tainted: G OE 5.15.0-43-generic torvalds#46-Ubunt u [4005007.702590] RIP: 0010:0x0 [4005007.702598] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. [4005007.702600] RSP: 0018:ffffa82b46d27da0 EFLAGS: 00010206 [4005007.702605] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffa82b46d27e68 [4005007.702609] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff9940656e0000 [4005007.702612] RBP: ffffa82b46d27dd8 R08: 0000000000000000 R09: ffff994060c07980 [4005007.702615] R10: 0000000000020000 R11: 0000000000000000 R12: 00007f5e06753000 [4005007.702618] R13: ffff9940656e0000 R14: ffffa82b46d27e68 R15: 00007f5e06753000 [4005007.702622] FS: 00007f5e0755b740(0000) GS:ffff99479d300000(0000) knlGS:0000000000000000 [4005007.702626] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [4005007.702629] CR2: ffffffffffffffd6 CR3: 00000003253fc000 CR4: 00000000003506e0 [4005007.702633] Call Trace: [4005007.702636] <TASK> [4005007.702640] amdgpu_debugfs_regs_smc_read+0xb0/0x120 [amdgpu] [4005007.703002] full_proxy_read+0x5c/0x80 [4005007.703011] vfs_read+0x9f/0x1a0 [4005007.703019] ksys_read+0x67/0xe0 [4005007.703023] __x64_sys_read+0x19/0x20 [4005007.703028] do_syscall_64+0x5c/0xc0 [4005007.703034] ? do_user_addr_fault+0x1e3/0x670 [4005007.703040] ? exit_to_user_mode_prepare+0x37/0xb0 [4005007.703047] ? irqentry_exit_to_user_mode+0x9/0x20 [4005007.703052] ? irqentry_exit+0x19/0x30 [4005007.703057] ? exc_page_fault+0x89/0x160 [4005007.703062] ? asm_exc_page_fault+0x8/0x30 [4005007.703068] entry_SYSCALL_64_after_hwframe+0x44/0xae [4005007.703075] RIP: 0033:0x7f5e07672992 [4005007.703079] Code: c0 e9 b2 fe ff ff 50 48 8d 3d fa b2 0c 00 e8 c5 1d 02 00 0f 1f 44 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 0f 05 <48> 3d 00 f0 ff ff 77 56 c3 0f 1f 44 00 00 48 83 e c 28 48 89 54 24 [4005007.703083] RSP: 002b:00007ffe03097898 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [4005007.703088] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5e07672992 [4005007.703091] RDX: 0000000000020000 RSI: 00007f5e06753000 RDI: 0000000000000003 [4005007.703094] RBP: 00007f5e06753000 R08: 00007f5e06752010 R09: 00007f5e06752010 [4005007.703096] R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000022000 [4005007.703099] R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000 [4005007.703105] </TASK> [4005007.703107] Modules linked in: nf_tables libcrc32c nfnetlink algif_hash af_alg binfmt_misc nls_ iso8859_1 ipmi_ssif ast intel_rapl_msr intel_rapl_common drm_vram_helper drm_ttm_helper amd64_edac t tm edac_mce_amd kvm_amd ccp mac_hid k10temp kvm acpi_ipmi ipmi_si rapl sch_fq_codel ipmi_devintf ipm i_msghandler msr parport_pc ppdev lp parport mtd pstore_blk efi_pstore ramoops pstore_zone reed_solo mon ip_tables x_tables autofs4 ib_uverbs ib_core amdgpu(OE) amddrm_ttm_helper(OE) amdttm(OE) iommu_v 2 amd_sched(OE) amdkcl(OE) drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm igb ahci xhci_pci libahci i2c_piix4 i2c_algo_bit xhci_pci_renesas dca [4005007.703184] CR2: 0000000000000000 [4005007.703188] ---[ end trace ac65a538d240da39 ]--- [4005007.800865] RIP: 0010:0x0 [4005007.800871] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. [4005007.800874] RSP: 0018:ffffa82b46d27da0 EFLAGS: 00010206 [4005007.800878] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffa82b46d27e68 [4005007.800881] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff9940656e0000 [4005007.800883] RBP: ffffa82b46d27dd8 R08: 0000000000000000 R09: ffff994060c07980 [4005007.800886] R10: 0000000000020000 R11: 0000000000000000 R12: 00007f5e06753000 [4005007.800888] R13: ffff9940656e0000 R14: ffffa82b46d27e68 R15: 00007f5e06753000 [4005007.800891] FS: 00007f5e0755b740(0000) GS:ffff99479d300000(0000) knlGS:0000000000000000 [4005007.800895] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [4005007.800898] CR2: ffffffffffffffd6 CR3: 00000003253fc000 CR4: 00000000003506e0 Signed-off-by: Qu Huang <qu.huang@linux.dev> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 87c3a58 ] Except on x86, preempt_count is always accessed with READ_ONCE(). Repeated invocations in macros like irq_count() produce repeated loads. These redundant instructions appear in various fast paths. In the one shown below, for example, irq_count() is evaluated during kernel entry if !tick_nohz_full_cpu(smp_processor_id()). 0001ed0a <irq_enter_rcu>: 1ed0a: 4e56 0000 linkw %fp,#0 1ed0e: 200f movel %sp,%d0 1ed10: 0280 ffff e000 andil #-8192,%d0 1ed16: 2040 moveal %d0,%a0 1ed18: 2028 0008 movel %a0@(8),%d0 1ed1c: 0680 0001 0000 addil #65536,%d0 1ed22: 2140 0008 movel %d0,%a0@(8) 1ed26: 082a 0001 000f btst #1,%a2@(15) 1ed2c: 670c beqs 1ed3a <irq_enter_rcu+0x30> 1ed2e: 2028 0008 movel %a0@(8),%d0 1ed32: 2028 0008 movel %a0@(8),%d0 1ed36: 2028 0008 movel %a0@(8),%d0 1ed3a: 4e5e unlk %fp 1ed3c: 4e75 rts This patch doesn't prevent the pointless btst and beqs instructions above, but it does eliminate 2 of the 3 pointless move instructions here and elsewhere. On x86, preempt_count is per-cpu data and the problem does not arise presumably because the compiler is free to optimize more effectively. This patch was tested on m68k and x86. I was expecting no changes to object code for x86 and mostly that's what I saw. However, there were a few places where code generation was perturbed for some reason. The performance issue addressed here is minor on uniprocessor m68k. I got a 0.01% improvement from this patch for a simple "find /sys -false" benchmark. For architectures and workloads susceptible to cache line bounce the improvement is expected to be larger. The only SMP architecture I have is x86, and as x86 unaffected I have not done any further measurements. Fixes: 1511583 ("preempt: Cleanup the macro maze a bit") Signed-off-by: Finn Thain <fthain@linux-m68k.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/0a403120a682a525e6db2d81d1a3ffcc137c3742.1694756831.git.fthain@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7b0033d ] In my test case, concurrent calls to f2fs shutdown report the following stack trace: Oops: general protection fault, probably for non-canonical address 0xc6cfff63bb5513fc: 0000 [#1] PREEMPT SMP PTI CPU: 0 UID: 0 PID: 678 Comm: f2fs_rep_shutdo Not tainted 6.12.0-rc5-next-20241029-g6fb2fa9805c5-dirty torvalds#85 Call Trace: <TASK> ? show_regs+0x8b/0xa0 ? __die_body+0x26/0xa0 ? die_addr+0x54/0x90 ? exc_general_protection+0x24b/0x5c0 ? asm_exc_general_protection+0x26/0x30 ? kthread_stop+0x46/0x390 f2fs_stop_gc_thread+0x6c/0x110 f2fs_do_shutdown+0x309/0x3a0 f2fs_ioc_shutdown+0x150/0x1c0 __f2fs_ioctl+0xffd/0x2ac0 f2fs_ioctl+0x76/0xe0 vfs_ioctl+0x23/0x60 __x64_sys_ioctl+0xce/0xf0 x64_sys_call+0x2b1b/0x4540 do_syscall_64+0xa7/0x240 entry_SYSCALL_64_after_hwframe+0x76/0x7e The root cause is a race condition in f2fs_stop_gc_thread() called from different f2fs shutdown paths: [CPU0] [CPU1] ---------------------- ----------------------- f2fs_stop_gc_thread f2fs_stop_gc_thread gc_th = sbi->gc_thread gc_th = sbi->gc_thread kfree(gc_th) sbi->gc_thread = NULL < gc_th != NULL > kthread_stop(gc_th->f2fs_gc_task) //UAF The commit c7f114d ("f2fs: fix to avoid use-after-free in f2fs_stop_gc_thread()") attempted to fix this issue by using a read semaphore to prevent races between shutdown and remount threads, but it fails to prevent all race conditions. Fix it by converting to write lock of s_umount in f2fs_do_shutdown(). Fixes: 7950e9a ("f2fs: stop gc/discard thread after fs shutdown") Signed-off-by: Long Li <leo.lilong@huawei.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f8c989a ] The last reference for `cache_head` can be reduced to zero in `c_show` and `e_show`(using `rcu_read_lock` and `rcu_read_unlock`). Consequently, `svc_export_put` and `expkey_put` will be invoked, leading to two issues: 1. The `svc_export_put` will directly free ex_uuid. However, `e_show`/`c_show` will access `ex_uuid` after `cache_put`, which can trigger a use-after-free issue, shown below. ================================================================== BUG: KASAN: slab-use-after-free in svc_export_show+0x362/0x430 [nfsd] Read of size 1 at addr ff11000010fdc120 by task cat/870 CPU: 1 UID: 0 PID: 870 Comm: cat Not tainted 6.12.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 print_address_description.constprop.0+0x2c/0x3a0 print_report+0xb9/0x280 kasan_report+0xae/0xe0 svc_export_show+0x362/0x430 [nfsd] c_show+0x161/0x390 [sunrpc] seq_read_iter+0x589/0x770 seq_read+0x1e5/0x270 proc_reg_read+0xe1/0x140 vfs_read+0x125/0x530 ksys_read+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Allocated by task 830: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x8f/0xa0 __kmalloc_node_track_caller_noprof+0x1bc/0x400 kmemdup_noprof+0x22/0x50 svc_export_parse+0x8a9/0xb80 [nfsd] cache_do_downcall+0x71/0xa0 [sunrpc] cache_write_procfs+0x8e/0xd0 [sunrpc] proc_reg_write+0xe1/0x140 vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 868: kasan_save_stack+0x20/0x40 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x37/0x50 kfree+0xf3/0x3e0 svc_export_put+0x87/0xb0 [nfsd] cache_purge+0x17f/0x1f0 [sunrpc] nfsd_destroy_serv+0x226/0x2d0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1a5/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e 2. We cannot sleep while using `rcu_read_lock`/`rcu_read_unlock`. However, `svc_export_put`/`expkey_put` will call path_put, which subsequently triggers a sleeping operation due to the following `dput`. ============================= WARNING: suspicious RCU usage 5.10.0-dirty torvalds#141 Not tainted ----------------------------- ... Call Trace: dump_stack+0x9a/0xd0 ___might_sleep+0x231/0x240 dput+0x39/0x600 path_put+0x1b/0x30 svc_export_put+0x17/0x80 e_show+0x1c9/0x200 seq_read_iter+0x63f/0x7c0 seq_read+0x226/0x2d0 vfs_read+0x113/0x2c0 ksys_read+0xc9/0x170 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x67/0xd1 Fix these issues by using `rcu_work` to help release `svc_expkey`/`svc_export`. This approach allows for an asynchronous context to invoke `path_put` and also facilitates the freeing of `uuid/exp/key` after an RCU grace period. Fixes: 9ceddd9 ("knfsd: Allow lockless lookups of the exports") Signed-off-by: Yang Erkun <yangerkun@huawei.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce89e74 ] There's issue as follows: RPC: Registered rdma transport module. RPC: Registered rdma backchannel transport module. RPC: Unregistered rdma transport module. RPC: Unregistered rdma backchannel transport module. BUG: unable to handle page fault for address: fffffbfff80c609a PGD 123fee067 P4D 123fee067 PUD 123fea067 PMD 10c624067 PTE 0 Oops: Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI RIP: 0010:percpu_counter_destroy_many+0xf7/0x2a0 Call Trace: <TASK> __die+0x1f/0x70 page_fault_oops+0x2cd/0x860 spurious_kernel_fault+0x36/0x450 do_kern_addr_fault+0xca/0x100 exc_page_fault+0x128/0x150 asm_exc_page_fault+0x26/0x30 percpu_counter_destroy_many+0xf7/0x2a0 mmdrop+0x209/0x350 finish_task_switch.isra.0+0x481/0x840 schedule_tail+0xe/0xd0 ret_from_fork+0x23/0x80 ret_from_fork_asm+0x1a/0x30 </TASK> If register_sysctl() return NULL, then svc_rdma_proc_cleanup() will not destroy the percpu counters which init in svc_rdma_proc_init(). If CONFIG_HOTPLUG_CPU is enabled, residual nodes may be in the 'percpu_counters' list. The above issue may occur once the module is removed. If the CONFIG_HOTPLUG_CPU configuration is not enabled, memory leakage occurs. To solve above issue just destroy all percpu counters when register_sysctl() return NULL. Fixes: 1e7e557 ("svcrdma: Restore read and write stats") Fixes: 22df5a2 ("svcrdma: Convert rdma_stat_sq_starve to a per-CPU counter") Fixes: df971cd ("svcrdma: Convert rdma_stat_recv to a per-CPU counter") Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fe4bf8d ] There are cases where a PCIe extended capability should be hidden from the user. For example, an unknown capability (i.e., capability with ID greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally chosen to be hidden from the user. Hiding a capability is done by virtualizing and modifying the 'Next Capability Offset' field of the previous capability so it points to the capability after the one that should be hidden. The special case where the first capability in the list should be hidden is handled differently because there is no previous capability that can be modified. In this case, the capability ID and version are zeroed while leaving the next pointer intact. This hides the capability and leaves an anchor for the rest of the capability list. However, today, hiding the first capability in the list is not done properly if the capability is unknown, as struct vfio_pci_core_device->pci_config_map is set to the capability ID during initialization but the capability ID is not properly checked later when used in vfio_config_do_rw(). This leads to the following warning [1] and to an out-of-bounds access to ecap_perms array. Fix it by checking cap_id in vfio_config_do_rw(), and if it is greater than PCI_EXT_CAP_ID_MAX, use an alternative struct perm_bits for direct read only access instead of the ecap_perms array. Note that this is safe since the above is the only case where cap_id can exceed PCI_EXT_CAP_ID_MAX (except for the special capabilities, which are already checked before). [1] WARNING: CPU: 118 PID: 5329 at drivers/vfio/pci/vfio_pci_config.c:1900 vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] CPU: 118 UID: 0 PID: 5329 Comm: simx-qemu-syste Not tainted 6.12.0+ #1 (snip) Call Trace: <TASK> ? show_regs+0x69/0x80 ? __warn+0x8d/0x140 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? report_bug+0x18f/0x1a0 ? handle_bug+0x63/0xa0 ? exc_invalid_op+0x19/0x70 ? asm_exc_invalid_op+0x1b/0x20 ? vfio_pci_config_rw+0x395/0x430 [vfio_pci_core] ? vfio_pci_config_rw+0x244/0x430 [vfio_pci_core] vfio_pci_rw+0x101/0x1b0 [vfio_pci_core] vfio_pci_core_read+0x1d/0x30 [vfio_pci_core] vfio_device_fops_read+0x27/0x40 [vfio] vfs_read+0xbd/0x340 ? vfio_device_fops_unl_ioctl+0xbb/0x740 [vfio] ? __rseq_handle_notify_resume+0xa4/0x4b0 __x64_sys_pread64+0x96/0xc0 x64_sys_call+0x1c3d/0x20d0 do_syscall_64+0x4d/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fixes: 89e1f7d ("vfio: Add PCI device driver") Signed-off-by: Avihai Horon <avihaih@nvidia.com> Reviewed-by: Yi Liu <yi.l.liu@intel.com> Tested-by: Yi Liu <yi.l.liu@intel.com> Link: https://lore.kernel.org/r/20241124142739.21698-1-avihaih@nvidia.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ebaf813 ] Passing MSG_PEEK flag to skb_recv_datagram() increments skb refcount (skb->users) and iucv_sock_recvmsg() does not decrement skb refcount at exit. This results in skb memory leak in skb_queue_purge() and WARN_ON in iucv_sock_destruct() during socket close. To fix this decrease skb refcount by one if MSG_PEEK is set in order to prevent memory leak and WARN_ON. WARNING: CPU: 2 PID: 6292 at net/iucv/af_iucv.c:286 iucv_sock_destruct+0x144/0x1a0 [af_iucv] CPU: 2 PID: 6292 Comm: afiucv_test_msg Kdump: loaded Tainted: G W 6.10.0-rc7 #1 Hardware name: IBM 3931 A01 704 (z/VM 7.3.0) Call Trace: [<001587c682c4aa98>] iucv_sock_destruct+0x148/0x1a0 [af_iucv] [<001587c682c4a9d0>] iucv_sock_destruct+0x80/0x1a0 [af_iucv] [<001587c704117a32>] __sk_destruct+0x52/0x550 [<001587c704104a54>] __sock_release+0xa4/0x230 [<001587c704104c0c>] sock_close+0x2c/0x40 [<001587c702c5f5a8>] __fput+0x2e8/0x970 [<001587c7024148c4>] task_work_run+0x1c4/0x2c0 [<001587c7023b0716>] do_exit+0x996/0x1050 [<001587c7023b13aa>] do_group_exit+0x13a/0x360 [<001587c7023b1626>] __s390x_sys_exit_group+0x56/0x60 [<001587c7022bccca>] do_syscall+0x27a/0x380 [<001587c7049a6a0c>] __do_syscall+0x9c/0x160 [<001587c7049ce8a8>] system_call+0x70/0x98 Last Breaking-Event-Address: [<001587c682c4a9d4>] iucv_sock_destruct+0x84/0x1a0 [af_iucv] Fixes: eac3731 ("[S390]: Add AF_IUCV socket support") Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com> Signed-off-by: Sidraya Jayagond <sidraya@linux.ibm.com> Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: David Wei <dw@davidwei.uk> Link: https://patch.msgid.link/20241119152219.3712168-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a66dfaf ] This fixes possible deadlocks like the following caused by hci_cmd_sync_dequeue causing the destroy function to run: INFO: task kworker/u19:0:143 blocked for more than 120 seconds. Tainted: G W O 6.8.0-2024-03-19-intel-next-iLS-24ww14 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u19:0 state:D stack:0 pid:143 tgid:143 ppid:2 flags:0x00004000 Workqueue: hci0 hci_cmd_sync_work [bluetooth] Call Trace: <TASK> __schedule+0x374/0xaf0 schedule+0x3c/0xf0 schedule_preempt_disabled+0x1c/0x30 __mutex_lock.constprop.0+0x3ef/0x7a0 __mutex_lock_slowpath+0x13/0x20 mutex_lock+0x3c/0x50 mgmt_set_connectable_complete+0xa4/0x150 [bluetooth] ? kfree+0x211/0x2a0 hci_cmd_sync_dequeue+0xae/0x130 [bluetooth] ? __pfx_cmd_complete_rsp+0x10/0x10 [bluetooth] cmd_complete_rsp+0x26/0x80 [bluetooth] mgmt_pending_foreach+0x4d/0x70 [bluetooth] __mgmt_power_off+0x8d/0x180 [bluetooth] ? _raw_spin_unlock_irq+0x23/0x40 hci_dev_close_sync+0x445/0x5b0 [bluetooth] hci_set_powered_sync+0x149/0x250 [bluetooth] set_powered_sync+0x24/0x60 [bluetooth] hci_cmd_sync_work+0x90/0x150 [bluetooth] process_one_work+0x13e/0x300 worker_thread+0x2f7/0x420 ? __pfx_worker_thread+0x10/0x10 kthread+0x107/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x3d/0x60 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> Tested-by: Kiran K <kiran.k@intel.com> Fixes: f53e1c9 ("Bluetooth: MGMT: Fix possible crash on mgmt_index_removed") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d73dc7b ] [Syzbot reported two possible deadlocks] The first possible deadlock is: WARNING: possible recursive locking detected 6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted -------------------------------------------- syz-executor363/2651 is trying to acquire lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322 but task is already holding lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(chaoskey_list_lock); lock(chaoskey_list_lock); *** DEADLOCK *** The second possible deadlock is: WARNING: possible circular locking dependency detected 6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted ------------------------------------------------------ kworker/0:2/804 is trying to acquire lock: ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186 but task is already holding lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (chaoskey_list_lock){+.+.}-{3:3}: __mutex_lock_common kernel/locking/mutex.c:608 [inline] __mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752 chaoskey_open+0xdd/0x220 drivers/usb/misc/chaoskey.c:274 usb_open+0x186/0x220 drivers/usb/core/file.c:47 chrdev_open+0x237/0x6a0 fs/char_dev.c:414 do_dentry_open+0x6cb/0x1390 fs/open.c:958 vfs_open+0x82/0x3f0 fs/open.c:1088 do_open fs/namei.c:3774 [inline] path_openat+0x1e6a/0x2d60 fs/namei.c:3933 do_filp_open+0x1dc/0x430 fs/namei.c:3960 do_sys_openat2+0x17a/0x1e0 fs/open.c:1415 do_sys_open fs/open.c:1430 [inline] __do_sys_openat fs/open.c:1446 [inline] __se_sys_openat fs/open.c:1441 [inline] __x64_sys_openat+0x175/0x210 fs/open.c:1441 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (minor_rwsem){++++}-{3:3}: check_prev_add kernel/locking/lockdep.c:3161 [inline] check_prevs_add kernel/locking/lockdep.c:3280 [inline] validate_chain kernel/locking/lockdep.c:3904 [inline] __lock_acquire+0x250b/0x3ce0 kernel/locking/lockdep.c:5202 lock_acquire.part.0+0x11b/0x380 kernel/locking/lockdep.c:5825 down_write+0x93/0x200 kernel/locking/rwsem.c:1577 usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186 chaoskey_disconnect+0xb7/0x2a0 drivers/usb/misc/chaoskey.c:236 usb_unbind_interface+0x1e8/0x970 drivers/usb/core/driver.c:461 device_remove drivers/base/dd.c:569 [inline] device_remove+0x122/0x170 drivers/base/dd.c:561 __device_release_driver drivers/base/dd.c:1273 [inline] device_release_driver_internal+0x44a/0x610 drivers/base/dd.c:1296 bus_remove_device+0x22f/0x420 drivers/base/bus.c:576 device_del+0x396/0x9f0 drivers/base/core.c:3864 usb_disable_device+0x36c/0x7f0 drivers/usb/core/message.c:1418 usb_disconnect+0x2e1/0x920 drivers/usb/core/hub.c:2304 hub_port_connect drivers/usb/core/hub.c:5361 [inline] hub_port_connect_change drivers/usb/core/hub.c:5661 [inline] port_event drivers/usb/core/hub.c:5821 [inline] hub_event+0x1bed/0x4f40 drivers/usb/core/hub.c:5903 process_one_work+0x9c5/0x1ba0 kernel/workqueue.c:3229 process_scheduled_works kernel/workqueue.c:3310 [inline] worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391 kthread+0x2c1/0x3a0 kernel/kthread.c:389 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(chaoskey_list_lock); lock(minor_rwsem); lock(chaoskey_list_lock); lock(minor_rwsem); *** DEADLOCK *** [Analysis] The first is AA lock, it because wrong logic, it need a unlock. The second is AB lock, it needs to rearrange the order of lock usage. Fixes: 422dc0a ("USB: chaoskey: fail open after removal") Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc Signed-off-by: Edward Adam Davis <eadavis@qq.com> Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 339b84a upstream. If a BUG_ON() can be hit in the wild, it shouldn't be a BUG_ON() For reference, this has popped up once in the CI, and we'll need more info to debug it: 03240 ------------[ cut here ]------------ 03240 kernel BUG at lib/closure.c:21! 03240 kernel BUG at lib/closure.c:21! 03240 Internal error: Oops - BUG: 00000000f2000800 [#1] SMP 03240 Modules linked in: 03240 CPU: 15 PID: 40534 Comm: kworker/u80:1 Not tainted 6.10.0-rc4-ktest-ga56da69799bd #25570 03240 Hardware name: linux,dummy-virt (DT) 03240 Workqueue: btree_update btree_interior_update_work 03240 pstate: 00001005 (nzcv daif -PAN -UAO -TCO -DIT +SSBS BTYPE=--) 03240 pc : closure_put+0x224/0x2a0 03240 lr : closure_put+0x24/0x2a0 03240 sp : ffff0000d12071c0 03240 x29: ffff0000d12071c0 x28: dfff800000000000 x27: ffff0000d1207360 03240 x26: 0000000000000040 x25: 0000000000000040 x24: 0000000000000040 03240 x23: ffff0000c1f20180 x22: 0000000000000000 x21: ffff0000c1f20168 03240 x20: 0000000040000000 x19: ffff0000c1f20140 x18: 0000000000000001 03240 x17: 0000000000003aa0 x16: 0000000000003ad0 x15: 1fffe0001c326974 03240 x14: 0000000000000a1e x13: 0000000000000000 x12: 1fffe000183e402d 03240 x11: ffff6000183e402d x10: dfff800000000000 x9 : ffff6000183e402e 03240 x8 : 0000000000000001 x7 : 00009fffe7c1bfd3 x6 : ffff0000c1f2016b 03240 x5 : ffff0000c1f20168 x4 : ffff6000183e402e x3 : ffff800081391954 03240 x2 : 0000000000000001 x1 : 0000000000000000 x0 : 00000000a8000000 03240 Call trace: 03240 closure_put+0x224/0x2a0 03240 bch2_check_for_deadlock+0x910/0x1028 03240 bch2_six_check_for_deadlock+0x1c/0x30 03240 six_lock_slowpath.isra.0+0x29c/0xed0 03240 six_lock_ip_waiter+0xa8/0xf8 03240 __bch2_btree_node_lock_write+0x14c/0x298 03240 bch2_trans_lock_write+0x6d4/0xb10 03240 __bch2_trans_commit+0x135c/0x5520 03240 btree_interior_update_work+0x1248/0x1c10 03240 process_scheduled_works+0x53c/0xd90 03240 worker_thread+0x370/0x8c8 03240 kthread+0x258/0x2e8 03240 ret_from_fork+0x10/0x20 03240 Code: aa1303e0 d63f0020 a94363f7 17ffff8c (d4210000) 03240 ---[ end trace 0000000000000000 ]--- 03240 Kernel panic - not syncing: Oops - BUG: Fatal exception 03240 SMP: stopping secondary CPUs 03241 SMP: failed to stop secondary CPUs 13,15 03241 Kernel Offset: disabled 03241 CPU features: 0x00,00000003,80000008,4240500b 03241 Memory Limit: none 03241 ---[ end Kernel panic - not syncing: Oops - BUG: Fatal exception ]--- 03246 ========= FAILED TIMEOUT copygc_torture_no_checksum in 7200s Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev> [ Resolve minor conflicts to fix CVE-2024-42252 ] Signed-off-by: Bin Lan <bin.lan.cn@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c7acef9 upstream. Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock. Since commit 0fc7088 ("thunderbolt: Reset USB4 v2 host router") and commit 59a54c5 ("thunderbolt: Reset topology created by the boot firmware"), USB4 v2 and v1 Host Routers are reset on probe of the thunderbolt driver. The reset clears the Presence Detect State and Data Link Layer Link Active bits at the USB4 Host Router's Root Port and thus causes hot removal of the dock. The crash occurs when pciehp is unbound from one of the dock's Downstream Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The pci_slot contains a pointer to the pci_bus below the Downstream Port, but a reference on that pci_bus is never acquired. The pci_bus is destroyed before the pci_slot, so a use-after-free ensues when pci_slot_release() accesses slot->bus. In principle this should not happen because pci_stop_bus_device() unbinds pciehp (and therefore destroys the pci_slot) before the pci_bus is destroyed by pci_remove_bus_device(). However the stacktrace provided by Dennis shows that pciehp is unbound from pci_remove_bus_device() instead of pci_stop_bus_device(). To understand the significance of this, one needs to know that the PCI core uses a two step process to remove a portion of the hierarchy: It first unbinds all drivers in the sub-hierarchy in pci_stop_bus_device() and then actually removes the devices in pci_remove_bus_device(). There is no precaution to prevent driver binding in-between pci_stop_bus_device() and pci_remove_bus_device(). In Dennis' case, it seems removal of the hierarchy by pciehp races with driver binding by pci_bus_add_devices(). pciehp is bound to the Downstream Port after pci_stop_bus_device() has run, so it is unbound by pci_remove_bus_device() instead of pci_stop_bus_device(). Because the pci_bus has already been destroyed at that point, accesses to it result in a use-after-free. One might conclude that driver binding needs to be prevented after pci_stop_bus_device() has run. However it seems risky that pci_slot points to pci_bus without holding a reference. Solely relying on correct ordering of driver unbind versus pci_bus destruction is certainly not defensive programming. If pci_slot has a need to access data in pci_bus, it ought to acquire a reference. Amend pci_create_slot() accordingly. Dennis reports that the crash is not reproducible with this change. Abridged stacktrace: pcieport 0000:00:07.0: PME: Signaling with IRQ 156 pcieport 0000:00:07.0: pciehp: Slot #12 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ pci_bus 0000:20: dev 00, created physical slot 12 pcieport 0000:00:07.0: pciehp: Slot(12): Card not present ... pcieport 0000:21:02.0: pciehp: pcie_disable_notification: SLOTCTRL d8 write cmd 0 Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] PREEMPT SMP NOPTI CPU: 13 UID: 0 PID: 134 Comm: irq/156-pciehp Not tainted 6.11.0-devel+ #1 RIP: 0010:dev_driver_string+0x12/0x40 pci_destroy_slot pciehp_remove pcie_port_remove_service device_release_driver_internal bus_remove_device device_del device_unregister remove_iter device_for_each_child pcie_portdrv_remove pci_device_remove device_release_driver_internal bus_remove_device device_del pci_remove_bus_device (recursive invocation) pci_remove_bus_device pciehp_unconfigure_device pciehp_disable_slot pciehp_handle_presence_or_link_change pciehp_ist Link: https://lore.kernel.org/r/4bfd4c0e976c1776cd08e76603903b338cf25729.1728579288.git.lukas@wunner.de Reported-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com> Closes: https://lore.kernel.org/r/6de4b45ff2b32dd91a805ec02ec8ec73ef411bf6.camel@secunet.com/ Tested-by: Dennis Wassenberg <Dennis.Wassenberg@secunet.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4bdec0d upstream. Neither SMB3.0 or SMB3.02 supports encryption negotiate context, so when SMB2_GLOBAL_CAP_ENCRYPTION flag is set in the negotiate response, the client uses AES-128-CCM as the default cipher. See MS-SMB2 3.3.5.4. Commit b0abcd6 ("smb: client: fix UAF in async decryption") added a @server->cipher_type check to conditionally call smb3_crypto_aead_allocate(), but that check would always be false as @server->cipher_type is unset for SMB3.02. Fix the following KASAN splat by setting @server->cipher_type for SMB3.02 as well. mount.cifs //srv/share /mnt -o vers=3.02,seal,... BUG: KASAN: null-ptr-deref in crypto_aead_setkey+0x2c/0x130 Read of size 8 at addr 0000000000000020 by task mount.cifs/1095 CPU: 1 UID: 0 PID: 1095 Comm: mount.cifs Not tainted 6.12.0 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-3.fc41 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 ? crypto_aead_setkey+0x2c/0x130 kasan_report+0xda/0x110 ? crypto_aead_setkey+0x2c/0x130 crypto_aead_setkey+0x2c/0x130 crypt_message+0x258/0xec0 [cifs] ? __asan_memset+0x23/0x50 ? __pfx_crypt_message+0x10/0x10 [cifs] ? mark_lock+0xb0/0x6a0 ? hlock_class+0x32/0xb0 ? mark_lock+0xb0/0x6a0 smb3_init_transform_rq+0x352/0x3f0 [cifs] ? lock_acquire.part.0+0xf4/0x2a0 smb_send_rqst+0x144/0x230 [cifs] ? __pfx_smb_send_rqst+0x10/0x10 [cifs] ? hlock_class+0x32/0xb0 ? smb2_setup_request+0x225/0x3a0 [cifs] ? __pfx_cifs_compound_last_callback+0x10/0x10 [cifs] compound_send_recv+0x59b/0x1140 [cifs] ? __pfx_compound_send_recv+0x10/0x10 [cifs] ? __create_object+0x5e/0x90 ? hlock_class+0x32/0xb0 ? do_raw_spin_unlock+0x9a/0xf0 cifs_send_recv+0x23/0x30 [cifs] SMB2_tcon+0x3ec/0xb30 [cifs] ? __pfx_SMB2_tcon+0x10/0x10 [cifs] ? lock_acquire.part.0+0xf4/0x2a0 ? __pfx_lock_release+0x10/0x10 ? do_raw_spin_trylock+0xc6/0x120 ? lock_acquire+0x3f/0x90 ? _get_xid+0x16/0xd0 [cifs] ? __pfx_SMB2_tcon+0x10/0x10 [cifs] ? cifs_get_smb_ses+0xcdd/0x10a0 [cifs] cifs_get_smb_ses+0xcdd/0x10a0 [cifs] ? __pfx_cifs_get_smb_ses+0x10/0x10 [cifs] ? cifs_get_tcp_session+0xaa0/0xca0 [cifs] cifs_mount_get_session+0x8a/0x210 [cifs] dfs_mount_share+0x1b0/0x11d0 [cifs] ? __pfx___lock_acquire+0x10/0x10 ? __pfx_dfs_mount_share+0x10/0x10 [cifs] ? lock_acquire.part.0+0xf4/0x2a0 ? find_held_lock+0x8a/0xa0 ? hlock_class+0x32/0xb0 ? lock_release+0x203/0x5d0 cifs_mount+0xb3/0x3d0 [cifs] ? do_raw_spin_trylock+0xc6/0x120 ? __pfx_cifs_mount+0x10/0x10 [cifs] ? lock_acquire+0x3f/0x90 ? find_nls+0x16/0xa0 ? smb3_update_mnt_flags+0x372/0x3b0 [cifs] cifs_smb3_do_mount+0x1e2/0xc80 [cifs] ? __pfx_vfs_parse_fs_string+0x10/0x10 ? __pfx_cifs_smb3_do_mount+0x10/0x10 [cifs] smb3_get_tree+0x1bf/0x330 [cifs] vfs_get_tree+0x4a/0x160 path_mount+0x3c1/0xfb0 ? kasan_quarantine_put+0xc7/0x1d0 ? __pfx_path_mount+0x10/0x10 ? kmem_cache_free+0x118/0x3e0 ? user_path_at+0x74/0xa0 __x64_sys_mount+0x1a6/0x1e0 ? __pfx___x64_sys_mount+0x10/0x10 ? mark_held_locks+0x1a/0x90 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f Cc: Tom Talpey <tom@talpey.com> Reported-by: Jianhong Yin <jiyin@redhat.com> Cc: stable@vger.kernel.org # v6.12 Fixes: b0abcd6 ("smb: client: fix UAF in async decryption") Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5bee35e upstream. The drvdata is not available in release. Let's just use container_of() to get the ubd instance. Otherwise, removing a ubd device will result in a crash: RIP: 0033:blk_mq_free_tag_set+0x1f/0xba RSP: 00000000e2083bf0 EFLAGS: 00010246 RAX: 000000006021463a RBX: 0000000000000348 RCX: 0000000062604d00 RDX: 0000000004208060 RSI: 00000000605241a0 RDI: 0000000000000348 RBP: 00000000e2083c10 R08: 0000000062414010 R09: 00000000601603f7 R10: 000000000000133a R11: 000000006038c4bd R12: 0000000000000000 R13: 0000000060213a5c R14: 0000000062405d20 R15: 00000000604f7aa0 Kernel panic - not syncing: Segfault with no mm CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 6.8.0-rc3-00107-gba3f67c11638 #1 Workqueue: events mc_work_proc Stack: 00000000 604f7ef0 62c5d000 62405d20 e2083c30 6002c776 6002c755 600e47ff e2083c60 6025ffe3 04208060 603d36e0 Call Trace: [<6002c776>] ubd_device_release+0x21/0x55 [<6002c755>] ? ubd_device_release+0x0/0x55 [<600e47ff>] ? kfree+0x0/0x100 [<6025ffe3>] device_release+0x70/0xba [<60381d6a>] kobject_put+0xb5/0xe2 [<6026027b>] put_device+0x19/0x1c [<6026a036>] platform_device_put+0x26/0x29 [<6026ac5a>] platform_device_unregister+0x2c/0x2e [<6002c52e>] ubd_remove+0xb8/0xd6 [<6002bb74>] ? mconsole_reply+0x0/0x50 [<6002b926>] mconsole_remove+0x160/0x1cc [<6002bbbc>] ? mconsole_reply+0x48/0x50 [<6003379c>] ? um_set_signals+0x3b/0x43 [<60061c55>] ? update_min_vruntime+0x14/0x70 [<6006251f>] ? dequeue_task_fair+0x164/0x235 [<600620aa>] ? update_cfs_group+0x0/0x40 [<603a0e77>] ? __schedule+0x0/0x3ed [<60033761>] ? um_set_signals+0x0/0x43 [<6002af6a>] mc_work_proc+0x77/0x91 [<600520b4>] process_scheduled_works+0x1af/0x2c3 [<6004ede3>] ? assign_work+0x0/0x58 [<600527a1>] worker_thread+0x2f7/0x37a [<6004ee3b>] ? set_pf_worker+0x0/0x64 [<6005765d>] ? arch_local_irq_save+0x0/0x2d [<60058e07>] ? kthread_exit+0x0/0x3a [<600524aa>] ? worker_thread+0x0/0x37a [<60058f9f>] kthread+0x130/0x135 [<6002068e>] new_thread_handler+0x85/0xb6 Cc: stable@vger.kernel.org Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Link: https://patch.msgid.link/20241104163203.435515-3-tiwei.btw@antgroup.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d1db692 upstream. The drvdata is not available in release. Let's just use container_of() to get the uml_net instance. Otherwise, removing a network device will result in a crash: RIP: 0033:net_device_release+0x10/0x6f RSP: 00000000e20c7c40 EFLAGS: 00010206 RAX: 000000006002e4e7 RBX: 00000000600f1baf RCX: 00000000624074e0 RDX: 0000000062778000 RSI: 0000000060551c80 RDI: 00000000627af028 RBP: 00000000e20c7c50 R08: 00000000603ad594 R09: 00000000e20c7b70 R10: 000000000000135a R11: 00000000603ad422 R12: 0000000000000000 R13: 0000000062c7af00 R14: 0000000062406d60 R15: 00000000627700b6 Kernel panic - not syncing: Segfault with no mm CPU: 0 UID: 0 PID: 29 Comm: kworker/0:2 Not tainted 6.12.0-rc6-g59b723cd2adb #1 Workqueue: events mc_work_proc Stack: 627af028 62c7af00 e20c7c80 60276fcd 62778000 603f5820 627af028 00000000 e20c7cb0 603a2bcd 627af000 62770010 Call Trace: [<60276fcd>] device_release+0x70/0xba [<603a2bcd>] kobject_put+0xba/0xe7 [<60277265>] put_device+0x19/0x1c [<60281266>] platform_device_put+0x26/0x29 [<60281e5f>] platform_device_unregister+0x2c/0x2e [<6002ec9c>] net_remove+0x63/0x69 [<60031316>] ? mconsole_reply+0x0/0x50 [<600310c8>] mconsole_remove+0x160/0x1cc [<60087d40>] ? __remove_hrtimer+0x38/0x74 [<60087ff8>] ? hrtimer_try_to_cancel+0x8c/0x98 [<6006b3cf>] ? dl_server_stop+0x3f/0x48 [<6006b390>] ? dl_server_stop+0x0/0x48 [<600672e8>] ? dequeue_entities+0x327/0x390 [<60038fa6>] ? um_set_signals+0x0/0x43 [<6003070c>] mc_work_proc+0x77/0x91 [<60057664>] process_scheduled_works+0x1b3/0x2dd [<60055f32>] ? assign_work+0x0/0x58 [<60057f0a>] worker_thread+0x1e9/0x293 [<6005406f>] ? set_pf_worker+0x0/0x64 [<6005d65d>] ? arch_local_irq_save+0x0/0x2d [<6005d748>] ? kthread_exit+0x0/0x3a [<60057d21>] ? worker_thread+0x0/0x293 [<6005dbf1>] kthread+0x126/0x12b [<600219c5>] new_thread_handler+0x85/0xb6 Cc: stable@vger.kernel.org Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Link: https://patch.msgid.link/20241104163203.435515-4-tiwei.btw@antgroup.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 51b39d7 upstream. The drvdata is not available in release. Let's just use container_of() to get the vector_device instance. Otherwise, removing a vector device will result in a crash: RIP: 0033:vector_device_release+0xf/0x50 RSP: 00000000e187bc40 EFLAGS: 00010202 RAX: 0000000060028f61 RBX: 00000000600f1baf RCX: 00000000620074e0 RDX: 000000006220b9c0 RSI: 0000000060551c80 RDI: 0000000000000000 RBP: 00000000e187bc50 R08: 00000000603ad594 R09: 00000000e187bb70 R10: 000000000000135a R11: 00000000603ad422 R12: 00000000623ae028 R13: 000000006287a200 R14: 0000000062006d30 R15: 00000000623700b6 Kernel panic - not syncing: Segfault with no mm CPU: 0 UID: 0 PID: 16 Comm: kworker/0:1 Not tainted 6.12.0-rc6-g59b723cd2adb #1 Workqueue: events mc_work_proc Stack: 60028f61 623ae028 e187bc80 60276fcd 6220b9c0 603f5820 623ae028 00000000 e187bcb0 603a2bcd 623ae000 62370010 Call Trace: [<60028f61>] ? vector_device_release+0x0/0x50 [<60276fcd>] device_release+0x70/0xba [<603a2bcd>] kobject_put+0xba/0xe7 [<60277265>] put_device+0x19/0x1c [<60281266>] platform_device_put+0x26/0x29 [<60281e5f>] platform_device_unregister+0x2c/0x2e [<60029422>] vector_remove+0x52/0x58 [<60031316>] ? mconsole_reply+0x0/0x50 [<600310c8>] mconsole_remove+0x160/0x1cc [<603b19f4>] ? strlen+0x0/0x15 [<60066611>] ? __dequeue_entity+0x1a9/0x206 [<600666a7>] ? set_next_entity+0x39/0x63 [<6006666e>] ? set_next_entity+0x0/0x63 [<60038fa6>] ? um_set_signals+0x0/0x43 [<6003070c>] mc_work_proc+0x77/0x91 [<60057664>] process_scheduled_works+0x1b3/0x2dd [<60055f32>] ? assign_work+0x0/0x58 [<60057f0a>] worker_thread+0x1e9/0x293 [<6005406f>] ? set_pf_worker+0x0/0x64 [<6005d65d>] ? arch_local_irq_save+0x0/0x2d [<6005d748>] ? kthread_exit+0x0/0x3a [<60057d21>] ? worker_thread+0x0/0x293 [<6005dbf1>] kthread+0x126/0x12b [<600219c5>] new_thread_handler+0x85/0xb6 Cc: stable@vger.kernel.org Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Link: https://patch.msgid.link/20241104163203.435515-5-tiwei.btw@antgroup.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7afb867 upstream. open_cached_dir() may either race with the tcon reconnection even before compound_send_recv() or directly trigger a reconnection via SMB2_open_init() or SMB_query_info_init(). The reconnection process invokes invalidate_all_cached_dirs() via cifs_mark_open_files_invalid(), which removes all cfids from the cfids->entries list but doesn't drop a ref if has_lease isn't true. This results in the currently-being-constructed cfid not being on the list, but still having a refcount of 2. It leaks if returned from open_cached_dir(). Fix this by setting cfid->has_lease when the ref is actually taken; the cfid will not be used by other threads until it has a valid time. Addresses these kmemleaks: unreferenced object 0xffff8881090c4000 (size 1024): comm "bash", pid 1860, jiffies 4295126592 hex dump (first 32 bytes): 00 01 00 00 00 00 ad de 22 01 00 00 00 00 ad de ........"....... 00 ca 45 22 81 88 ff ff f8 dc 4f 04 81 88 ff ff ..E"......O..... backtrace (crc 6f58c20f): [<ffffffff8b895a1e>] __kmalloc_cache_noprof+0x2be/0x350 [<ffffffff8bda06e3>] open_cached_dir+0x993/0x1fb0 [<ffffffff8bdaa750>] cifs_readdir+0x15a0/0x1d50 [<ffffffff8b9a853f>] iterate_dir+0x28f/0x4b0 [<ffffffff8b9a9aed>] __x64_sys_getdents64+0xfd/0x200 [<ffffffff8cf6da05>] do_syscall_64+0x95/0x1a0 [<ffffffff8d00012f>] entry_SYSCALL_64_after_hwframe+0x76/0x7e unreferenced object 0xffff8881044fdcf8 (size 8): comm "bash", pid 1860, jiffies 4295126592 hex dump (first 8 bytes): 00 cc cc cc cc cc cc cc ........ backtrace (crc 10c106a9): [<ffffffff8b89a3d3>] __kmalloc_node_track_caller_noprof+0x363/0x480 [<ffffffff8b7d7256>] kstrdup+0x36/0x60 [<ffffffff8bda0700>] open_cached_dir+0x9b0/0x1fb0 [<ffffffff8bdaa750>] cifs_readdir+0x15a0/0x1d50 [<ffffffff8b9a853f>] iterate_dir+0x28f/0x4b0 [<ffffffff8b9a9aed>] __x64_sys_getdents64+0xfd/0x200 [<ffffffff8cf6da05>] do_syscall_64+0x95/0x1a0 [<ffffffff8d00012f>] entry_SYSCALL_64_after_hwframe+0x76/0x7e And addresses these BUG splats when unmounting the SMB filesystem: BUG: Dentry ffff888140590ba0{i=1000000000080,n=/} still in use (2) [unmount of cifs cifs] WARNING: CPU: 3 PID: 3433 at fs/dcache.c:1536 umount_check+0xd0/0x100 Modules linked in: CPU: 3 UID: 0 PID: 3433 Comm: bash Not tainted 6.12.0-rc4-g850925a8133c-dirty torvalds#49 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 RIP: 0010:umount_check+0xd0/0x100 Code: 8d 7c 24 40 e8 31 5a f4 ff 49 8b 54 24 40 41 56 49 89 e9 45 89 e8 48 89 d9 41 57 48 89 de 48 c7 c7 80 e7 db ac e8 f0 72 9a ff <0f> 0b 58 31 c0 5a 5b 5d 41 5c 41 5d 41 5e 41 5f e9 2b e5 5d 01 41 RSP: 0018:ffff88811cc27978 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff888140590ba0 RCX: ffffffffaaf20bae RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff8881f6fb6f40 RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed1023984ee3 R10: ffff88811cc2771f R11: 00000000016cfcc0 R12: ffff888134383e08 R13: 0000000000000002 R14: ffff8881462ec668 R15: ffffffffaceab4c0 FS: 00007f23bfa98740(0000) GS:ffff8881f6f80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000556de4a6f808 CR3: 0000000123c80000 CR4: 0000000000350ef0 Call Trace: <TASK> d_walk+0x6a/0x530 shrink_dcache_for_umount+0x6a/0x200 generic_shutdown_super+0x52/0x2a0 kill_anon_super+0x22/0x40 cifs_kill_sb+0x159/0x1e0 deactivate_locked_super+0x66/0xe0 cleanup_mnt+0x140/0x210 task_work_run+0xfb/0x170 syscall_exit_to_user_mode+0x29f/0x2b0 do_syscall_64+0xa1/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f23bfb93ae7 Code: ff ff ff ff c3 66 0f 1f 44 00 00 48 8b 0d 11 93 0d 00 f7 d8 64 89 01 b8 ff ff ff ff eb bf 0f 1f 44 00 00 b8 50 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d e9 92 0d 00 f7 d8 64 89 01 48 RSP: 002b:00007ffee9138598 EFLAGS: 00000246 ORIG_RAX: 0000000000000050 RAX: 0000000000000000 RBX: 0000558f1803e9a0 RCX: 00007f23bfb93ae7 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000558f1803e9a0 RBP: 0000558f1803e600 R08: 0000000000000007 R09: 0000558f17fab610 R10: d91d5ec34ab757b0 R11: 0000000000000246 R12: 0000000000000001 R13: 0000000000000000 R14: 0000000000000015 R15: 0000000000000000 </TASK> irq event stamp: 1163486 hardirqs last enabled at (1163485): [<ffffffffac98d344>] _raw_spin_unlock_irqrestore+0x34/0x60 hardirqs last disabled at (1163486): [<ffffffffac97dcfc>] __schedule+0xc7c/0x19a0 softirqs last enabled at (1163482): [<ffffffffab79a3ee>] __smb_send_rqst+0x3de/0x990 softirqs last disabled at (1163480): [<ffffffffac2314f1>] release_sock+0x21/0xf0 ---[ end trace 0000000000000000 ]--- VFS: Busy inodes after unmount of cifs (cifs) ------------[ cut here ]------------ kernel BUG at fs/super.c:661! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 1 UID: 0 PID: 3433 Comm: bash Tainted: G W 6.12.0-rc4-g850925a8133c-dirty torvalds#49 Tainted: [W]=WARN Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 RIP: 0010:generic_shutdown_super+0x290/0x2a0 Code: e8 15 7c f7 ff 48 8b 5d 28 48 89 df e8 09 7c f7 ff 48 8b 0b 48 89 ee 48 8d 95 68 06 00 00 48 c7 c7 80 7f db ac e8 00 69 af ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 90 90 90 90 90 90 RSP: 0018:ffff88811cc27a50 EFLAGS: 00010246 RAX: 000000000000003e RBX: ffffffffae994420 RCX: 0000000000000027 RDX: 0000000000000000 RSI: ffffffffab06180e RDI: ffff8881f6eb18c8 RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed103edd6319 R10: ffff8881f6eb18cb R11: 00000000016d3158 R12: ffff8881462ec9c0 R13: ffff8881462ec050 R14: 0000000000000001 R15: 0000000000000000 FS: 00007f23bfa98740(0000) GS:ffff8881f6e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8364005d68 CR3: 0000000123c80000 CR4: 0000000000350ef0 Call Trace: <TASK> kill_anon_super+0x22/0x40 cifs_kill_sb+0x159/0x1e0 deactivate_locked_super+0x66/0xe0 cleanup_mnt+0x140/0x210 task_work_run+0xfb/0x170 syscall_exit_to_user_mode+0x29f/0x2b0 do_syscall_64+0xa1/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f23bfb93ae7 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:generic_shutdown_super+0x290/0x2a0 Code: e8 15 7c f7 ff 48 8b 5d 28 48 89 df e8 09 7c f7 ff 48 8b 0b 48 89 ee 48 8d 95 68 06 00 00 48 c7 c7 80 7f db ac e8 00 69 af ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 90 90 90 90 90 90 RSP: 0018:ffff88811cc27a50 EFLAGS: 00010246 RAX: 000000000000003e RBX: ffffffffae994420 RCX: 0000000000000027 RDX: 0000000000000000 RSI: ffffffffab06180e RDI: ffff8881f6eb18c8 RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed103edd6319 R10: ffff8881f6eb18cb R11: 00000000016d3158 R12: ffff8881462ec9c0 R13: ffff8881462ec050 R14: 0000000000000001 R15: 0000000000000000 FS: 00007f23bfa98740(0000) GS:ffff8881f6e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8364005d68 CR3: 0000000123c80000 CR4: 0000000000350ef0 This reproduces eventually with an SMB mount and two shells running these loops concurrently - while true; do cd ~; sleep 1; for i in {1..3}; do cd /mnt/test/subdir; echo $PWD; sleep 1; cd ..; echo $PWD; sleep 1; done; echo ...; done - while true; do iptables -F OUTPUT; mount -t cifs -a; for _ in {0..2}; do ls /mnt/test/subdir/ | wc -l; done; iptables -I OUTPUT -p tcp --dport 445 -j DROP; sleep 10 echo "unmounting"; umount -l -t cifs -a; echo "done unmounting"; sleep 20 echo "recovering"; iptables -F OUTPUT; sleep 10; done Fixes: ebe98f1 ("cifs: enable caching of directories for which a lease is held") Fixes: 5c86919 ("smb: client: fix use-after-free in smb2_query_info_compound()") Cc: stable@vger.kernel.org Signed-off-by: Paul Aurich <paul@darkrain42.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2862eee upstream. The function `c_show` was called with protection from RCU. This only ensures that `cp` will not be freed. Therefore, the reference count for `cp` can drop to zero, which will trigger a refcount use-after-free warning when `cache_get` is called. To resolve this issue, use `cache_get_rcu` to ensure that `cp` remains active. ------------[ cut here ]------------ refcount_t: addition on 0; use-after-free. WARNING: CPU: 7 PID: 822 at lib/refcount.c:25 refcount_warn_saturate+0xb1/0x120 CPU: 7 UID: 0 PID: 822 Comm: cat Not tainted 6.12.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 RIP: 0010:refcount_warn_saturate+0xb1/0x120 Call Trace: <TASK> c_show+0x2fc/0x380 [sunrpc] seq_read_iter+0x589/0x770 seq_read+0x1e5/0x270 proc_reg_read+0xe1/0x140 vfs_read+0x125/0x530 ksys_read+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: Yang Erkun <yangerkun@huawei.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fd0af4c upstream. The power suppliers are always requested to suspend asynchronously, dev_pm_domain_detach() requires the caller to ensure proper synchronization of this function with power management callbacks. otherwise the detach may led to kernel panic, like below: [ 1457.107934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000040 [ 1457.116777] Mem abort info: [ 1457.119589] ESR = 0x0000000096000004 [ 1457.123358] EC = 0x25: DABT (current EL), IL = 32 bits [ 1457.128692] SET = 0, FnV = 0 [ 1457.131764] EA = 0, S1PTW = 0 [ 1457.134920] FSC = 0x04: level 0 translation fault [ 1457.139812] Data abort info: [ 1457.142707] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 1457.148196] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 1457.153256] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 1457.158563] user pgtable: 4k pages, 48-bit VAs, pgdp=00000001138b6000 [ 1457.165000] [0000000000000040] pgd=0000000000000000, p4d=0000000000000000 [ 1457.171792] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 1457.178045] Modules linked in: v4l2_jpeg wave6_vpu_ctrl(-) [last unloaded: mxc_jpeg_encdec] [ 1457.186383] CPU: 0 PID: 51938 Comm: kworker/0:3 Not tainted 6.6.36-gd23d64eea511 torvalds#66 [ 1457.194112] Hardware name: NXP i.MX95 19X19 board (DT) [ 1457.199236] Workqueue: pm pm_runtime_work [ 1457.203247] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1457.210188] pc : genpd_runtime_suspend+0x20/0x290 [ 1457.214886] lr : __rpm_callback+0x48/0x1d8 [ 1457.218968] sp : ffff80008250bc50 [ 1457.222270] x29: ffff80008250bc50 x28: 0000000000000000 x27: 0000000000000000 [ 1457.229394] x26: 0000000000000000 x25: 0000000000000008 x24: 00000000000f4240 [ 1457.236518] x23: 0000000000000000 x22: ffff00008590f0e4 x21: 0000000000000008 [ 1457.243642] x20: ffff80008099c434 x19: ffff00008590f000 x18: ffffffffffffffff [ 1457.250766] x17: 5300326563697665 x16: 645f676e696c6f6f x15: 63343a6d726f6674 [ 1457.257890] x14: 0000000000000004 x13: 00000000000003a4 x12: 0000000000000002 [ 1457.265014] x11: 0000000000000000 x10: 0000000000000a60 x9 : ffff80008250bbb0 [ 1457.272138] x8 : ffff000092937200 x7 : ffff0003fdf6af80 x6 : 0000000000000000 [ 1457.279262] x5 : 00000000410fd050 x4 : 0000000000200000 x3 : 0000000000000000 [ 1457.286386] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00008590f000 [ 1457.293510] Call trace: [ 1457.295946] genpd_runtime_suspend+0x20/0x290 [ 1457.300296] __rpm_callback+0x48/0x1d8 [ 1457.304038] rpm_callback+0x6c/0x78 [ 1457.307515] rpm_suspend+0x10c/0x570 [ 1457.311077] pm_runtime_work+0xc4/0xc8 [ 1457.314813] process_one_work+0x138/0x248 [ 1457.318816] worker_thread+0x320/0x438 [ 1457.322552] kthread+0x110/0x114 [ 1457.325767] ret_from_fork+0x10/0x20 Fixes: 2db16c6 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder") Cc: <stable@vger.kernel.org> Signed-off-by: Ming Qian <ming.qian@nxp.com> Reviewed-by: TaoJiang <tao.jiang_2@nxp.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dbc1691 upstream. Boot with slub_debug=UFPZ. If allocated object failed in alloc_consistency_checks, all objects of the slab will be marked as used, and then the slab will be removed from the partial list. When an object belonging to the slab got freed later, the remove_full() function is called. Because the slab is neither on the partial list nor on the full list, it eventually lead to a list corruption (actually a list poison being detected). So we need to mark and isolate the slab page with metadata corruption, do not put it back in circulation. Because the debug caches avoid all the fastpaths, reusing the frozen bit to mark slab page with metadata corruption seems to be fine. [ 4277.385669] list_del corruption, ffffea00044b3e50->next is LIST_POISON1 (dead000000000100) [ 4277.387023] ------------[ cut here ]------------ [ 4277.387880] kernel BUG at lib/list_debug.c:56! [ 4277.388680] invalid opcode: 0000 [#1] PREEMPT SMP PTI [ 4277.389562] CPU: 5 PID: 90 Comm: kworker/5:1 Kdump: loaded Tainted: G OE 6.6.1-1 #1 [ 4277.392113] Workqueue: xfs-inodegc/vda1 xfs_inodegc_worker [xfs] [ 4277.393551] RIP: 0010:__list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.394518] Code: 48 91 82 e8 37 f9 9a ff 0f 0b 48 89 fe 48 c7 c7 28 49 91 82 e8 26 f9 9a ff 0f 0b 48 89 fe 48 c7 c7 58 49 91 [ 4277.397292] RSP: 0018:ffffc90000333b38 EFLAGS: 00010082 [ 4277.398202] RAX: 000000000000004e RBX: ffffea00044b3e50 RCX: 0000000000000000 [ 4277.399340] RDX: 0000000000000002 RSI: ffffffff828f8715 RDI: 00000000ffffffff [ 4277.400545] RBP: ffffea00044b3e40 R08: 0000000000000000 R09: ffffc900003339f0 [ 4277.401710] R10: 0000000000000003 R11: ffffffff82d44088 R12: ffff888112cf9910 [ 4277.402887] R13: 0000000000000001 R14: 0000000000000001 R15: ffff8881000424c0 [ 4277.404049] FS: 0000000000000000(0000) GS:ffff88842fd40000(0000) knlGS:0000000000000000 [ 4277.405357] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 4277.406389] CR2: 00007f2ad0b24000 CR3: 0000000102a3a006 CR4: 00000000007706e0 [ 4277.407589] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 4277.408780] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 4277.410000] PKRU: 55555554 [ 4277.410645] Call Trace: [ 4277.411234] <TASK> [ 4277.411777] ? die+0x32/0x80 [ 4277.412439] ? do_trap+0xd6/0x100 [ 4277.413150] ? __list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.414158] ? do_error_trap+0x6a/0x90 [ 4277.414948] ? __list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.415915] ? exc_invalid_op+0x4c/0x60 [ 4277.416710] ? __list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.417675] ? asm_exc_invalid_op+0x16/0x20 [ 4277.418482] ? __list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.419466] ? __list_del_entry_valid_or_report+0x7b/0xc0 [ 4277.420410] free_to_partial_list+0x515/0x5e0 [ 4277.421242] ? xfs_iext_remove+0x41a/0xa10 [xfs] [ 4277.422298] xfs_iext_remove+0x41a/0xa10 [xfs] [ 4277.423316] ? xfs_inodegc_worker+0xb4/0x1a0 [xfs] [ 4277.424383] xfs_bmap_del_extent_delay+0x4fe/0x7d0 [xfs] [ 4277.425490] __xfs_bunmapi+0x50d/0x840 [xfs] [ 4277.426445] xfs_itruncate_extents_flags+0x13a/0x490 [xfs] [ 4277.427553] xfs_inactive_truncate+0xa3/0x120 [xfs] [ 4277.428567] xfs_inactive+0x22d/0x290 [xfs] [ 4277.429500] xfs_inodegc_worker+0xb4/0x1a0 [xfs] [ 4277.430479] process_one_work+0x171/0x340 [ 4277.431227] worker_thread+0x277/0x390 [ 4277.431962] ? __pfx_worker_thread+0x10/0x10 [ 4277.432752] kthread+0xf0/0x120 [ 4277.433382] ? __pfx_kthread+0x10/0x10 [ 4277.434134] ret_from_fork+0x2d/0x50 [ 4277.434837] ? __pfx_kthread+0x10/0x10 [ 4277.435566] ret_from_fork_asm+0x1b/0x30 [ 4277.436280] </TASK> Fixes: 643b113 ("slub: enable tracking of full slabs") Suggested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Suggested-by: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by: yuan.gao <yuan.gao@ucloud.cn> Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit be8f982 upstream. The function `e_show` was called with protection from RCU. This only ensures that `exp` will not be freed. Therefore, the reference count for `exp` can drop to zero, which will trigger a refcount use-after-free warning when `exp_get` is called. To resolve this issue, use `cache_get_rcu` to ensure that `exp` remains active. ------------[ cut here ]------------ refcount_t: addition on 0; use-after-free. WARNING: CPU: 3 PID: 819 at lib/refcount.c:25 refcount_warn_saturate+0xb1/0x120 CPU: 3 UID: 0 PID: 819 Comm: cat Not tainted 6.12.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 RIP: 0010:refcount_warn_saturate+0xb1/0x120 ... Call Trace: <TASK> e_show+0x20b/0x230 [nfsd] seq_read_iter+0x589/0x770 seq_read+0x1e5/0x270 vfs_read+0x125/0x530 ksys_read+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fixes: bf18f16 ("NFSD: Using exp_get for export getting") Cc: stable@vger.kernel.org # 4.20+ Signed-off-by: Yang Erkun <yangerkun@huawei.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b61badd upstream. [ +0.000021] BUG: KASAN: slab-use-after-free in drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000027] Read of size 8 at addr ffff8881b8605f88 by task amd_pci_unplug/2147 [ +0.000023] CPU: 6 PID: 2147 Comm: amd_pci_unplug Not tainted 6.10.0+ #1 [ +0.000016] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000016] Call Trace: [ +0.000008] <TASK> [ +0.000009] dump_stack_lvl+0x76/0xa0 [ +0.000017] print_report+0xce/0x5f0 [ +0.000017] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000019] ? srso_return_thunk+0x5/0x5f [ +0.000015] ? kasan_complete_mode_report_info+0x72/0x200 [ +0.000016] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000019] kasan_report+0xbe/0x110 [ +0.000015] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000023] __asan_report_load8_noabort+0x14/0x30 [ +0.000014] drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_write+0x14/0x30 [ +0.000016] ? __pfx_drm_sched_entity_flush+0x10/0x10 [gpu_sched] [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_write+0x14/0x30 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? enable_work+0x124/0x220 [ +0.000015] ? __pfx_enable_work+0x10/0x10 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? free_large_kmalloc+0x85/0xf0 [ +0.000016] drm_sched_entity_destroy+0x18/0x30 [gpu_sched] [ +0.000020] amdgpu_vce_sw_fini+0x55/0x170 [amdgpu] [ +0.000735] ? __kasan_check_read+0x11/0x20 [ +0.000016] vce_v4_0_sw_fini+0x80/0x110 [amdgpu] [ +0.000726] amdgpu_device_fini_sw+0x331/0xfc0 [amdgpu] [ +0.000679] ? mutex_unlock+0x80/0xe0 [ +0.000017] ? __pfx_amdgpu_device_fini_sw+0x10/0x10 [amdgpu] [ +0.000662] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __kasan_check_write+0x14/0x30 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? mutex_unlock+0x80/0xe0 [ +0.000016] amdgpu_driver_release_kms+0x16/0x80 [amdgpu] [ +0.000663] drm_minor_release+0xc9/0x140 [drm] [ +0.000081] drm_release+0x1fd/0x390 [drm] [ +0.000082] __fput+0x36c/0xad0 [ +0.000018] __fput_sync+0x3c/0x50 [ +0.000014] __x64_sys_close+0x7d/0xe0 [ +0.000014] x64_sys_call+0x1bc6/0x2680 [ +0.000014] do_syscall_64+0x70/0x130 [ +0.000014] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? irqentry_exit_to_user_mode+0x60/0x190 [ +0.000015] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? irqentry_exit+0x43/0x50 [ +0.000012] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? exc_page_fault+0x7c/0x110 [ +0.000015] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000014] RIP: 0033:0x7ffff7b14f67 [ +0.000013] Code: ff e8 0d 16 02 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 41 c3 48 83 ec 18 89 7c 24 0c e8 73 ba f7 ff [ +0.000026] RSP: 002b:00007fffffffe378 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 [ +0.000019] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ffff7b14f67 [ +0.000014] RDX: 0000000000000000 RSI: 00007ffff7f6f47a RDI: 0000000000000003 [ +0.000014] RBP: 00007fffffffe3a0 R08: 0000555555569890 R09: 0000000000000000 [ +0.000014] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffffffe5c8 [ +0.000013] R13: 00005555555552a9 R14: 0000555555557d48 R15: 00007ffff7ffd040 [ +0.000020] </TASK> [ +0.000016] Allocated by task 383 on cpu 7 at 26.880319s: [ +0.000014] kasan_save_stack+0x28/0x60 [ +0.000008] kasan_save_track+0x18/0x70 [ +0.000007] kasan_save_alloc_info+0x38/0x60 [ +0.000007] __kasan_kmalloc+0xc1/0xd0 [ +0.000007] kmalloc_trace_noprof+0x180/0x380 [ +0.000007] drm_sched_init+0x411/0xec0 [gpu_sched] [ +0.000012] amdgpu_device_init+0x695f/0xa610 [amdgpu] [ +0.000658] amdgpu_driver_load_kms+0x1a/0x120 [amdgpu] [ +0.000662] amdgpu_pci_probe+0x361/0xf30 [amdgpu] [ +0.000651] local_pci_probe+0xe7/0x1b0 [ +0.000009] pci_device_probe+0x248/0x890 [ +0.000008] really_probe+0x1fd/0x950 [ +0.000008] __driver_probe_device+0x307/0x410 [ +0.000007] driver_probe_device+0x4e/0x150 [ +0.000007] __driver_attach+0x223/0x510 [ +0.000006] bus_for_each_dev+0x102/0x1a0 [ +0.000007] driver_attach+0x3d/0x60 [ +0.000006] bus_add_driver+0x2ac/0x5f0 [ +0.000006] driver_register+0x13d/0x490 [ +0.000008] __pci_register_driver+0x1ee/0x2b0 [ +0.000007] llc_sap_close+0xb0/0x160 [llc] [ +0.000009] do_one_initcall+0x9c/0x3e0 [ +0.000008] do_init_module+0x241/0x760 [ +0.000008] load_module+0x51ac/0x6c30 [ +0.000006] __do_sys_init_module+0x234/0x270 [ +0.000007] __x64_sys_init_module+0x73/0xc0 [ +0.000006] x64_sys_call+0xe3/0x2680 [ +0.000006] do_syscall_64+0x70/0x130 [ +0.000007] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000015] Freed by task 2147 on cpu 6 at 160.507651s: [ +0.000013] kasan_save_stack+0x28/0x60 [ +0.000007] kasan_save_track+0x18/0x70 [ +0.000007] kasan_save_free_info+0x3b/0x60 [ +0.000007] poison_slab_object+0x115/0x1c0 [ +0.000007] __kasan_slab_free+0x34/0x60 [ +0.000007] kfree+0xfa/0x2f0 [ +0.000007] drm_sched_fini+0x19d/0x410 [gpu_sched] [ +0.000012] amdgpu_fence_driver_sw_fini+0xc4/0x2f0 [amdgpu] [ +0.000662] amdgpu_device_fini_sw+0x77/0xfc0 [amdgpu] [ +0.000653] amdgpu_driver_release_kms+0x16/0x80 [amdgpu] [ +0.000655] drm_minor_release+0xc9/0x140 [drm] [ +0.000071] drm_release+0x1fd/0x390 [drm] [ +0.000071] __fput+0x36c/0xad0 [ +0.000008] __fput_sync+0x3c/0x50 [ +0.000007] __x64_sys_close+0x7d/0xe0 [ +0.000007] x64_sys_call+0x1bc6/0x2680 [ +0.000007] do_syscall_64+0x70/0x130 [ +0.000007] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000014] The buggy address belongs to the object at ffff8881b8605f80 which belongs to the cache kmalloc-64 of size 64 [ +0.000020] The buggy address is located 8 bytes inside of freed 64-byte region [ffff8881b8605f80, ffff8881b8605fc0) [ +0.000028] The buggy address belongs to the physical page: [ +0.000011] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1b8605 [ +0.000008] anon flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ +0.000007] page_type: 0xffffefff(slab) [ +0.000009] raw: 0017ffffc0000000 ffff8881000428c0 0000000000000000 dead000000000001 [ +0.000006] raw: 0000000000000000 0000000000200020 00000001ffffefff 0000000000000000 [ +0.000006] page dumped because: kasan: bad access detected [ +0.000012] Memory state around the buggy address: [ +0.000011] ffff8881b8605e80: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ +0.000015] ffff8881b8605f00: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc [ +0.000015] >ffff8881b8605f80: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ +0.000013] ^ [ +0.000011] ffff8881b8606000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fc [ +0.000014] ffff8881b8606080: fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb fb [ +0.000013] ================================================================== The issue reproduced on VG20 during the IGT pci_unplug test. The root cause of the issue is that the function drm_sched_fini is called before drm_sched_entity_kill. In drm_sched_fini, the drm_sched_rq structure is freed, but this structure is later accessed by each entity within the run queue, leading to invalid memory access. To resolve this, the order of cleanup calls is updated: Before: amdgpu_fence_driver_sw_fini amdgpu_device_ip_fini After: amdgpu_device_ip_fini amdgpu_fence_driver_sw_fini This updated order ensures that all entities in the IPs are cleaned up first, followed by proper cleanup of the schedulers. Additional Investigation: During debugging, another issue was identified in the amdgpu_vce_sw_fini function. The vce.vcpu_bo buffer must be freed only as the final step in the cleanup process to prevent any premature access during earlier cleanup stages. v2: Using Christian suggestion call drm_sched_entity_destroy before drm_sched_fini. Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5954821 upstream. Due to incorrect dev->product reporting by certain devices, null pointer dereferences occur when dev->product is empty, leading to potential system crashes. This issue was found on EXCELSIOR DL37-D05 device with Loongson-LS3A6000-7A2000-DL37 motherboard. Kernel logs: [ 56.470885] usb 4-3: new full-speed USB device number 4 using ohci-pci [ 56.671638] usb 4-3: string descriptor 0 read error: -22 [ 56.671644] usb 4-3: New USB device found, idVendor=056a, idProduct=0374, bcdDevice= 1.07 [ 56.671647] usb 4-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 56.678839] hid-generic 0003:056A:0374.0004: hiddev0,hidraw3: USB HID v1.10 Device [HID 056a:0374] on usb-0000:00:05.0-3/input0 [ 56.697719] CPU 2 Unable to handle kernel paging request at virtual address 0000000000000000, era == 90000000066e35c8, ra == ffff800004f98a80 [ 56.697732] Oops[#1]: [ 56.697734] CPU: 2 PID: 2742 Comm: (udev-worker) Tainted: G OE 6.6.0-loong64-desktop torvalds#25.00.2000.015 [ 56.697737] Hardware name: Inspur CE520L2/C09901N000000000, BIOS 2.09.00 10/11/2024 [ 56.697739] pc 90000000066e35c8 ra ffff800004f98a80 tp 9000000125478000 sp 900000012547b8a0 [ 56.697741] a0 0000000000000000 a1 ffff800004818b28 a2 0000000000000000 a3 0000000000000000 [ 56.697743] a4 900000012547b8f0 a5 0000000000000000 a6 0000000000000000 a7 0000000000000000 [ 56.697745] t0 ffff800004818b2d t1 0000000000000000 t2 0000000000000003 t3 0000000000000005 [ 56.697747] t4 0000000000000000 t5 0000000000000000 t6 0000000000000000 t7 0000000000000000 [ 56.697748] t8 0000000000000000 u0 0000000000000000 s9 0000000000000000 s0 900000011aa48028 [ 56.697750] s1 0000000000000000 s2 0000000000000000 s3 ffff800004818e80 s4 ffff800004810000 [ 56.697751] s5 90000001000b98d0 s6 ffff800004811f88 s7 ffff800005470440 s8 0000000000000000 [ 56.697753] ra: ffff800004f98a80 wacom_update_name+0xe0/0x300 [wacom] [ 56.697802] ERA: 90000000066e35c8 strstr+0x28/0x120 [ 56.697806] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) [ 56.697816] PRMD: 0000000c (PPLV0 +PIE +PWE) [ 56.697821] EUEN: 00000000 (-FPE -SXE -ASXE -BTE) [ 56.697827] ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) [ 56.697831] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0) [ 56.697835] BADV: 0000000000000000 [ 56.697836] PRID: 0014d000 (Loongson-64bit, Loongson-3A6000) [ 56.697838] Modules linked in: wacom(+) bnep bluetooth rfkill qrtr nls_iso8859_1 nls_cp437 snd_hda_codec_conexant snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_timer snd soundcore input_leds mousedev led_class joydev deepin_netmonitor(OE) fuse nfnetlink dmi_sysfs ip_tables x_tables overlay amdgpu amdxcp drm_exec gpu_sched drm_buddy radeon drm_suballoc_helper i2c_algo_bit drm_ttm_helper r8169 ttm drm_display_helper spi_loongson_pci xhci_pci cec xhci_pci_renesas spi_loongson_core hid_generic realtek gpio_loongson_64bit [ 56.697887] Process (udev-worker) (pid: 2742, threadinfo=00000000aee0d8b4, task=00000000a9eff1f3) [ 56.697890] Stack : 0000000000000000 ffff800004817e00 0000000000000000 0000251c00000000 [ 56.697896] 0000000000000000 00000011fffffffd 0000000000000000 0000000000000000 [ 56.697901] 0000000000000000 1b67a968695184b9 0000000000000000 90000001000b98d0 [ 56.697906] 90000001000bb8d0 900000011aa48028 0000000000000000 ffff800004f9d74c [ 56.697911] 90000001000ba000 ffff800004f9ce58 0000000000000000 ffff800005470440 [ 56.697916] ffff800004811f88 90000001000b98d0 9000000100da2aa8 90000001000bb8d0 [ 56.697921] 0000000000000000 90000001000ba000 900000011aa48028 ffff800004f9d74c [ 56.697926] ffff8000054704e8 90000001000bb8b8 90000001000ba000 0000000000000000 [ 56.697931] 90000001000bb8d0 9000000006307564 9000000005e666e0 90000001752359b8 [ 56.697936] 9000000008cbe400 900000000804d000 9000000005e666e0 0000000000000000 [ 56.697941] ... [ 56.697944] Call Trace: [ 56.697945] [<90000000066e35c8>] strstr+0x28/0x120 [ 56.697950] [<ffff800004f98a80>] wacom_update_name+0xe0/0x300 [wacom] [ 56.698000] [<ffff800004f9ce58>] wacom_parse_and_register+0x338/0x900 [wacom] [ 56.698050] [<ffff800004f9d74c>] wacom_probe+0x32c/0x420 [wacom] [ 56.698099] [<9000000006307564>] hid_device_probe+0x144/0x260 [ 56.698103] [<9000000005e65d68>] really_probe+0x208/0x540 [ 56.698109] [<9000000005e661dc>] __driver_probe_device+0x13c/0x1e0 [ 56.698112] [<9000000005e66620>] driver_probe_device+0x40/0x100 [ 56.698116] [<9000000005e6680c>] __device_attach_driver+0x12c/0x180 [ 56.698119] [<9000000005e62bc8>] bus_for_each_drv+0x88/0x160 [ 56.698123] [<9000000005e66468>] __device_attach+0x108/0x260 [ 56.698126] [<9000000005e63918>] device_reprobe+0x78/0x100 [ 56.698129] [<9000000005e62a68>] bus_for_each_dev+0x88/0x160 [ 56.698132] [<9000000006304e54>] __hid_bus_driver_added+0x34/0x80 [ 56.698134] [<9000000005e62bc8>] bus_for_each_drv+0x88/0x160 [ 56.698137] [<9000000006304df0>] __hid_register_driver+0x70/0xa0 [ 56.698142] [<9000000004e10fe4>] do_one_initcall+0x104/0x320 [ 56.698146] [<9000000004f38150>] do_init_module+0x90/0x2c0 [ 56.698151] [<9000000004f3a3d8>] init_module_from_file+0xb8/0x120 [ 56.698155] [<9000000004f3a590>] idempotent_init_module+0x150/0x3a0 [ 56.698159] [<9000000004f3a890>] sys_finit_module+0xb0/0x140 [ 56.698163] [<900000000671e4e8>] do_syscall+0x88/0xc0 [ 56.698166] [<9000000004e12404>] handle_syscall+0xc4/0x160 [ 56.698171] Code: 0011958f 00150224 5800cd85 <2a00022c> 00150004 4000c180 0015022c 03400000 03400000 [ 56.698192] ---[ end trace 0000000000000000 ]--- Fixes: 09dc28a ("HID: wacom: Improve generic name generation") Reported-by: Zhenxing Chen <chenzhenxing@uniontech.com> Co-developed-by: Xu Rao <raoxu@uniontech.com> Signed-off-by: Xu Rao <raoxu@uniontech.com> Signed-off-by: WangYuli <wangyuli@uniontech.com> Link: https://patch.msgid.link/B31757FE8E1544CF+20241125052616.18261-1-wangyuli@uniontech.com Cc: stable@vger.kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ee1dfbd upstream. In commit 6e86a15 ("can: dev: provide optional GPIO based termination support") GPIO based termination support was added. For no particular reason that patch uses gpiod_set_value() to set the GPIO. This leads to the following warning, if the systems uses a sleeping GPIO, i.e. behind an I2C port expander: | WARNING: CPU: 0 PID: 379 at /drivers/gpio/gpiolib.c:3496 gpiod_set_value+0x50/0x6c | CPU: 0 UID: 0 PID: 379 Comm: ip Not tainted 6.11.0-20241016-1 #1 823affae360cc91126e4d316d7a614a8bf86236c Replace gpiod_set_value() by gpiod_set_value_cansleep() to allow the use of sleeping GPIOs. Cc: Nicolai Buchwitz <nb@tipi-net.de> Cc: Lino Sanfilippo <l.sanfilippo@kunbus.com> Cc: stable@vger.kernel.org Reported-by: Leonard Göhrs <l.goehrs@pengutronix.de> Tested-by: Leonard Göhrs <l.goehrs@pengutronix.de> Fixes: 6e86a15 ("can: dev: provide optional GPIO based termination support") Link: https://patch.msgid.link/20241121-dev-fix-can_set_termination-v1-1-41fa6e29216d@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 07c903d upstream. System crash is observed with stack trace warning of use after free. There are 2 signals to tell dpc_thread to terminate (UNLOADING flag and kthread_stop). On setting the UNLOADING flag when dpc_thread happens to run at the time and sees the flag, this causes dpc_thread to exit and clean up itself. When kthread_stop is called for final cleanup, this causes use after free. Remove UNLOADING signal to terminate dpc_thread. Use the kthread_stop as the main signal to exit dpc_thread. [596663.812935] kernel BUG at mm/slub.c:294! [596663.812950] invalid opcode: 0000 [#1] SMP PTI [596663.812957] CPU: 13 PID: 1475935 Comm: rmmod Kdump: loaded Tainted: G IOE --------- - - 4.18.0-240.el8.x86_64 #1 [596663.812960] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 08/20/2012 [596663.812974] RIP: 0010:__slab_free+0x17d/0x360 ... [596663.813008] Call Trace: [596663.813022] ? __dentry_kill+0x121/0x170 [596663.813030] ? _cond_resched+0x15/0x30 [596663.813034] ? _cond_resched+0x15/0x30 [596663.813039] ? wait_for_completion+0x35/0x190 [596663.813048] ? try_to_wake_up+0x63/0x540 [596663.813055] free_task+0x5a/0x60 [596663.813061] kthread_stop+0xf3/0x100 [596663.813103] qla2x00_remove_one+0x284/0x440 [qla2xxx] Cc: stable@vger.kernel.org Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20241115130313.46826-3-njavali@marvell.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…imary CPU commit b3fce42 upstream. Commit 5944ce0 ("arch_topology: Build cacheinfo from primary CPU") adds functionality that architectures can use to optionally allocate and build cacheinfo early during boot. Commit 6539cff ("cacheinfo: Add arch specific early level initializer") lets secondary CPUs correct (and reallocate memory) cacheinfo data if needed. If the early build functionality is not used and cacheinfo does not need correction, memory for cacheinfo is never allocated. x86 does not use the early build functionality. Consequently, during the cacheinfo CPU hotplug callback, last_level_cache_is_valid() attempts to dereference a NULL pointer: BUG: kernel NULL pointer dereference, address: 0000000000000100 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not present page PGD 0 P4D 0 Oops: 0000 [#1] PREEPMT SMP NOPTI CPU: 0 PID 19 Comm: cpuhp/0 Not tainted 6.4.0-rc2 #1 RIP: 0010: last_level_cache_is_valid+0x95/0xe0a Allocate memory for cacheinfo during the cacheinfo CPU hotplug callback if not done earlier. Moreover, before determining the validity of the last-level cache info, ensure that it has been allocated. Simply checking for non-zero cache_leaves() is not sufficient, as some architectures (e.g., Intel processors) have non-zero cache_leaves() before allocation. Dereferencing NULL cacheinfo can occur in update_per_cpu_data_slice_size(). This function iterates over all online CPUs. However, a CPU may have come online recently, but its cacheinfo may not have been allocated yet. While here, remove an unnecessary indentation in allocate_cache_info(). [ bp: Massage. ] Fixes: 6539cff ("cacheinfo: Add arch specific early level initializer") Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Radu Rendec <rrendec@redhat.com> Reviewed-by: Nikolay Borisov <nik.borisov@suse.com> Reviewed-by: Andreas Herrmann <aherrmann@suse.de> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org # 6.3+ Link: https://lore.kernel.org/r/20241128002247.26726-2-ricardo.neri-calderon@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ab244dd upstream. Jordy reported issue against XSKMAP which also applies to DEVMAP - the index used for accessing map entry, due to being a signed integer, causes the OOB writes. Fix is simple as changing the type from int to u32, however, when compared to XSKMAP case, one more thing needs to be addressed. When map is released from system via dev_map_free(), we iterate through all of the entries and an iterator variable is also an int, which implies OOB accesses. Again, change it to be u32. Example splat below: [ 160.724676] BUG: unable to handle page fault for address: ffffc8fc2c001000 [ 160.731662] #PF: supervisor read access in kernel mode [ 160.736876] #PF: error_code(0x0000) - not-present page [ 160.742095] PGD 0 P4D 0 [ 160.744678] Oops: Oops: 0000 [#1] PREEMPT SMP [ 160.749106] CPU: 1 UID: 0 PID: 520 Comm: kworker/u145:12 Not tainted 6.12.0-rc1+ torvalds#487 [ 160.757050] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 160.767642] Workqueue: events_unbound bpf_map_free_deferred [ 160.773308] RIP: 0010:dev_map_free+0x77/0x170 [ 160.777735] Code: 00 e8 fd 91 ed ff e8 b8 73 ed ff 41 83 7d 18 19 74 6e 41 8b 45 24 49 8b bd f8 00 00 00 31 db 85 c0 74 48 48 63 c3 48 8d 04 c7 <48> 8b 28 48 85 ed 74 30 48 8b 7d 18 48 85 ff 74 05 e8 b3 52 fa ff [ 160.796777] RSP: 0018:ffffc9000ee1fe38 EFLAGS: 00010202 [ 160.802086] RAX: ffffc8fc2c001000 RBX: 0000000080000000 RCX: 0000000000000024 [ 160.809331] RDX: 0000000000000000 RSI: 0000000000000024 RDI: ffffc9002c001000 [ 160.816576] RBP: 0000000000000000 R08: 0000000000000023 R09: 0000000000000001 [ 160.823823] R10: 0000000000000001 R11: 00000000000ee6b2 R12: dead000000000122 [ 160.831066] R13: ffff88810c928e00 R14: ffff8881002df405 R15: 0000000000000000 [ 160.838310] FS: 0000000000000000(0000) GS:ffff8897e0c40000(0000) knlGS:0000000000000000 [ 160.846528] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 160.852357] CR2: ffffc8fc2c001000 CR3: 0000000005c32006 CR4: 00000000007726f0 [ 160.859604] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 160.866847] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 160.874092] PKRU: 55555554 [ 160.876847] Call Trace: [ 160.879338] <TASK> [ 160.881477] ? __die+0x20/0x60 [ 160.884586] ? page_fault_oops+0x15a/0x450 [ 160.888746] ? search_extable+0x22/0x30 [ 160.892647] ? search_bpf_extables+0x5f/0x80 [ 160.896988] ? exc_page_fault+0xa9/0x140 [ 160.900973] ? asm_exc_page_fault+0x22/0x30 [ 160.905232] ? dev_map_free+0x77/0x170 [ 160.909043] ? dev_map_free+0x58/0x170 [ 160.912857] bpf_map_free_deferred+0x51/0x90 [ 160.917196] process_one_work+0x142/0x370 [ 160.921272] worker_thread+0x29e/0x3b0 [ 160.925082] ? rescuer_thread+0x4b0/0x4b0 [ 160.929157] kthread+0xd4/0x110 [ 160.932355] ? kthread_park+0x80/0x80 [ 160.936079] ret_from_fork+0x2d/0x50 [ 160.943396] ? kthread_park+0x80/0x80 [ 160.950803] ret_from_fork_asm+0x11/0x20 [ 160.958482] </TASK> Fixes: 546ac1f ("bpf: add devmap, a map for storing net device references") CC: stable@vger.kernel.org Reported-by: Jordy Zomer <jordyzomer@google.com> Suggested-by: Jordy Zomer <jordyzomer@google.com> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20241122121030.716788-3-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 32cd3db upstream. Jordy says: " In the xsk_map_delete_elem function an unsigned integer (map->max_entries) is compared with a user-controlled signed integer (k). Due to implicit type conversion, a large unsigned value for map->max_entries can bypass the intended bounds check: if (k >= map->max_entries) return -EINVAL; This allows k to hold a negative value (between -2147483648 and -2), which is then used as an array index in m->xsk_map[k], which results in an out-of-bounds access. spin_lock_bh(&m->lock); map_entry = &m->xsk_map[k]; // Out-of-bounds map_entry old_xs = unrcu_pointer(xchg(map_entry, NULL)); // Oob write if (old_xs) xsk_map_sock_delete(old_xs, map_entry); spin_unlock_bh(&m->lock); The xchg operation can then be used to cause an out-of-bounds write. Moreover, the invalid map_entry passed to xsk_map_sock_delete can lead to further memory corruption. " It indeed results in following splat: [76612.897343] BUG: unable to handle page fault for address: ffffc8fc2e461108 [76612.904330] #PF: supervisor write access in kernel mode [76612.909639] #PF: error_code(0x0002) - not-present page [76612.914855] PGD 0 P4D 0 [76612.917431] Oops: Oops: 0002 [#1] PREEMPT SMP [76612.921859] CPU: 11 UID: 0 PID: 10318 Comm: a.out Not tainted 6.12.0-rc1+ torvalds#470 [76612.929189] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [76612.939781] RIP: 0010:xsk_map_delete_elem+0x2d/0x60 [76612.944738] Code: 00 00 41 54 55 53 48 63 2e 3b 6f 24 73 38 4c 8d a7 f8 00 00 00 48 89 fb 4c 89 e7 e8 2d bf 05 00 48 8d b4 eb 00 01 00 00 31 ff <48> 87 3e 48 85 ff 74 05 e8 16 ff ff ff 4c 89 e7 e8 3e bc 05 00 31 [76612.963774] RSP: 0018:ffffc9002e407df8 EFLAGS: 00010246 [76612.969079] RAX: 0000000000000000 RBX: ffffc9002e461000 RCX: 0000000000000000 [76612.976323] RDX: 0000000000000001 RSI: ffffc8fc2e461108 RDI: 0000000000000000 [76612.983569] RBP: ffffffff80000001 R08: 0000000000000000 R09: 0000000000000007 [76612.990812] R10: ffffc9002e407e18 R11: ffff888108a38858 R12: ffffc9002e4610f8 [76612.998060] R13: ffff888108a38858 R14: 00007ffd1ae0ac78 R15: ffffc9002e4610c0 [76613.005303] FS: 00007f80b6f59740(0000) GS:ffff8897e0ec0000(0000) knlGS:0000000000000000 [76613.013517] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [76613.019349] CR2: ffffc8fc2e461108 CR3: 000000011e3ef001 CR4: 00000000007726f0 [76613.026595] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [76613.033841] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [76613.041086] PKRU: 55555554 [76613.043842] Call Trace: [76613.046331] <TASK> [76613.048468] ? __die+0x20/0x60 [76613.051581] ? page_fault_oops+0x15a/0x450 [76613.055747] ? search_extable+0x22/0x30 [76613.059649] ? search_bpf_extables+0x5f/0x80 [76613.063988] ? exc_page_fault+0xa9/0x140 [76613.067975] ? asm_exc_page_fault+0x22/0x30 [76613.072229] ? xsk_map_delete_elem+0x2d/0x60 [76613.076573] ? xsk_map_delete_elem+0x23/0x60 [76613.080914] __sys_bpf+0x19b7/0x23c0 [76613.084555] __x64_sys_bpf+0x1a/0x20 [76613.088194] do_syscall_64+0x37/0xb0 [76613.091832] entry_SYSCALL_64_after_hwframe+0x4b/0x53 [76613.096962] RIP: 0033:0x7f80b6d1e88d [76613.100592] Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 73 b5 0f 00 f7 d8 64 89 01 48 [76613.119631] RSP: 002b:00007ffd1ae0ac68 EFLAGS: 00000206 ORIG_RAX: 0000000000000141 [76613.131330] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f80b6d1e88d [76613.142632] RDX: 0000000000000098 RSI: 00007ffd1ae0ad20 RDI: 0000000000000003 [76613.153967] RBP: 00007ffd1ae0adc0 R08: 0000000000000000 R09: 0000000000000000 [76613.166030] R10: 00007f80b6f77040 R11: 0000000000000206 R12: 00007ffd1ae0aed8 [76613.177130] R13: 000055ddf42ce1e9 R14: 000055ddf42d0d98 R15: 00007f80b6fab040 [76613.188129] </TASK> Fix this by simply changing key type from int to u32. Fixes: fbfc504 ("bpf: introduce new bpf AF_XDP map type BPF_MAP_TYPE_XSKMAP") CC: stable@vger.kernel.org Reported-by: Jordy Zomer <jordyzomer@google.com> Suggested-by: Jordy Zomer <jordyzomer@google.com> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20241122121030.716788-2-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b9e9ed9 ] For htab of maps, when the map is removed from the htab, it may hold the last reference of the map. bpf_map_fd_put_ptr() will invoke bpf_map_free_id() to free the id of the removed map element. However, bpf_map_fd_put_ptr() is invoked while holding a bucket lock (raw_spin_lock_t), and bpf_map_free_id() attempts to acquire map_idr_lock (spinlock_t), triggering the following lockdep warning: ============================= [ BUG: Invalid wait context ] 6.11.0-rc4+ torvalds#49 Not tainted ----------------------------- test_maps/4881 is trying to lock: ffffffff84884578 (map_idr_lock){+...}-{3:3}, at: bpf_map_free_id.part.0+0x21/0x70 other info that might help us debug this: context-{5:5} 2 locks held by test_maps/4881: #0: ffffffff846caf60 (rcu_read_lock){....}-{1:3}, at: bpf_fd_htab_map_update_elem+0xf9/0x270 #1: ffff888149ced148 (&htab->lockdep_key#2){....}-{2:2}, at: htab_map_update_elem+0x178/0xa80 stack backtrace: CPU: 0 UID: 0 PID: 4881 Comm: test_maps Not tainted 6.11.0-rc4+ torvalds#49 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ... Call Trace: <TASK> dump_stack_lvl+0x6e/0xb0 dump_stack+0x10/0x20 __lock_acquire+0x73e/0x36c0 lock_acquire+0x182/0x450 _raw_spin_lock_irqsave+0x43/0x70 bpf_map_free_id.part.0+0x21/0x70 bpf_map_put+0xcf/0x110 bpf_map_fd_put_ptr+0x9a/0xb0 free_htab_elem+0x69/0xe0 htab_map_update_elem+0x50f/0xa80 bpf_fd_htab_map_update_elem+0x131/0x270 htab_map_update_elem+0x50f/0xa80 bpf_fd_htab_map_update_elem+0x131/0x270 bpf_map_update_value+0x266/0x380 __sys_bpf+0x21bb/0x36b0 __x64_sys_bpf+0x45/0x60 x64_sys_call+0x1b2a/0x20d0 do_syscall_64+0x5d/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e One way to fix the lockdep warning is using raw_spinlock_t for map_idr_lock as well. However, bpf_map_alloc_id() invokes idr_alloc_cyclic() after acquiring map_idr_lock, it will trigger a similar lockdep warning because the slab's lock (s->cpu_slab->lock) is still a spinlock. Instead of changing map_idr_lock's type, fix the issue by invoking htab_put_fd_value() after htab_unlock_bucket(). However, only deferring the invocation of htab_put_fd_value() is not enough, because the old map pointers in htab of maps can not be saved during batched deletion. Therefore, also defer the invocation of free_htab_elem(), so these to-be-freed elements could be linked together similar to lru map. There are four callers for ->map_fd_put_ptr: (1) alloc_htab_elem() (through htab_put_fd_value()) It invokes ->map_fd_put_ptr() under a raw_spinlock_t. The invocation of htab_put_fd_value() can not simply move after htab_unlock_bucket(), because the old element has already been stashed in htab->extra_elems. It may be reused immediately after htab_unlock_bucket() and the invocation of htab_put_fd_value() after htab_unlock_bucket() may release the newly-added element incorrectly. Therefore, saving the map pointer of the old element for htab of maps before unlocking the bucket and releasing the map_ptr after unlock. Beside the map pointer in the old element, should do the same thing for the special fields in the old element as well. (2) free_htab_elem() (through htab_put_fd_value()) Its caller includes __htab_map_lookup_and_delete_elem(), htab_map_delete_elem() and __htab_map_lookup_and_delete_batch(). For htab_map_delete_elem(), simply invoke free_htab_elem() after htab_unlock_bucket(). For __htab_map_lookup_and_delete_batch(), just like lru map, linking the to-be-freed element into node_to_free list and invoking free_htab_elem() for these element after unlock. It is safe to reuse batch_flink as the link for node_to_free, because these elements have been removed from the hash llist. Because htab of maps doesn't support lookup_and_delete operation, __htab_map_lookup_and_delete_elem() doesn't have the problem, so kept it as is. (3) fd_htab_map_free() It invokes ->map_fd_put_ptr without raw_spinlock_t. (4) bpf_fd_htab_map_update_elem() It invokes ->map_fd_put_ptr without raw_spinlock_t. After moving free_htab_elem() outside htab bucket lock scope, using pcpu_freelist_push() instead of __pcpu_freelist_push() to disable the irq before freeing elements, and protecting the invocations of bpf_mem_cache_free() with migrate_{disable|enable} pair. Signed-off-by: Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/r/20241106063542.357743-2-houtao@huaweicloud.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ode. [ Upstream commit d5c367e ] creating a large files during checkpoint disable until it runs out of space and then delete it, then remount to enable checkpoint again, and then unmount the filesystem triggers the f2fs_bug_on as below: ------------[ cut here ]------------ kernel BUG at fs/f2fs/inode.c:896! CPU: 2 UID: 0 PID: 1286 Comm: umount Not tainted 6.11.0-rc7-dirty torvalds#360 Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:f2fs_evict_inode+0x58c/0x610 Call Trace: __die_body+0x15/0x60 die+0x33/0x50 do_trap+0x10a/0x120 f2fs_evict_inode+0x58c/0x610 do_error_trap+0x60/0x80 f2fs_evict_inode+0x58c/0x610 exc_invalid_op+0x53/0x60 f2fs_evict_inode+0x58c/0x610 asm_exc_invalid_op+0x16/0x20 f2fs_evict_inode+0x58c/0x610 evict+0x101/0x260 dispose_list+0x30/0x50 evict_inodes+0x140/0x190 generic_shutdown_super+0x2f/0x150 kill_block_super+0x11/0x40 kill_f2fs_super+0x7d/0x140 deactivate_locked_super+0x2a/0x70 cleanup_mnt+0xb3/0x140 task_work_run+0x61/0x90 The root cause is: creating large files during disable checkpoint period results in not enough free segments, so when writing back root inode will failed in f2fs_enable_checkpoint. When umount the file system after enabling checkpoint, the root inode is dirty in f2fs_evict_inode function, which triggers BUG_ON. The steps to reproduce are as follows: dd if=/dev/zero of=f2fs.img bs=1M count=55 mount f2fs.img f2fs_dir -o checkpoint=disable:10% dd if=/dev/zero of=big bs=1M count=50 sync rm big mount -o remount,checkpoint=enable f2fs_dir umount f2fs_dir Let's redirty inode when there is not free segments during checkpoint is disable. Signed-off-by: Qi Han <hanqi@vivo.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

…to avoid deadlock [ Upstream commit 6cf7b65 ] A deadlock may happen since the i3c_master_register() acquires &i3cbus->lock twice. See the log below. Use i3cdev->desc->info instead of calling i3c_device_info() to avoid acquiring the lock twice. v2: - Modified the title and commit message ============================================ WARNING: possible recursive locking detected 6.11.0-mainline -------------------------------------------- init/1 is trying to acquire lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_bus_normaluse_lock but task is already holding lock: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&i3cbus->lock); lock(&i3cbus->lock); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by init/1: #0: fcffff809b6798f8 (&dev->mutex){....}-{3:3}, at: __driver_attach #1: f1ffff80a6a40dc0 (&i3cbus->lock){++++}-{3:3}, at: i3c_master_register stack backtrace: CPU: 6 UID: 0 PID: 1 Comm: init Call trace: dump_backtrace+0xfc/0x17c show_stack+0x18/0x28 dump_stack_lvl+0x40/0xc0 dump_stack+0x18/0x24 print_deadlock_bug+0x388/0x390 __lock_acquire+0x18bc/0x32ec lock_acquire+0x134/0x2b0 down_read+0x50/0x19c i3c_bus_normaluse_lock+0x14/0x24 i3c_device_get_info+0x24/0x58 i3c_device_uevent+0x34/0xa4 dev_uevent+0x310/0x384 kobject_uevent_env+0x244/0x414 kobject_uevent+0x14/0x20 device_add+0x278/0x460 device_register+0x20/0x34 i3c_master_register_new_i3c_devs+0x78/0x154 i3c_master_register+0x6a0/0x6d4 mtk_i3c_master_probe+0x3b8/0x4d8 platform_probe+0xa0/0xe0 really_probe+0x114/0x454 __driver_probe_device+0xa0/0x15c driver_probe_device+0x3c/0x1ac __driver_attach+0xc4/0x1f0 bus_for_each_dev+0x104/0x160 driver_attach+0x24/0x34 bus_add_driver+0x14c/0x294 driver_register+0x68/0x104 __platform_driver_register+0x20/0x30 init_module+0x20/0xfe4 do_one_initcall+0x184/0x464 do_init_module+0x58/0x1ec load_module+0xefc/0x10c8 __arm64_sys_finit_module+0x238/0x33c invoke_syscall+0x58/0x10c el0_svc_common+0xa8/0xdc do_el0_svc+0x1c/0x28 el0_svc+0x50/0xac el0t_64_sync_handler+0x70/0xbc el0t_64_sync+0x1a8/0x1ac Signed-off-by: Defa Li <defa.li@mediatek.com> Link: https://lore.kernel.org/r/20241107132549.25439-1-defa.li@mediatek.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 88fd2b7 ] Commit bab1c29 ("LoongArch: Fix sleeping in atomic context in setup_tlb_handler()") changes the gfp flag from GFP_KERNEL to GFP_ATOMIC for alloc_pages_node(). However, for PREEMPT_RT kernels we can still get a "sleeping in atomic context" error: [ 0.372259] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 0.372266] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1 [ 0.372268] preempt_count: 1, expected: 0 [ 0.372270] RCU nest depth: 1, expected: 1 [ 0.372272] 3 locks held by swapper/1/0: [ 0.372274] #0: 900000000c9f5e60 (&pcp->lock){+.+.}-{3:3}, at: get_page_from_freelist+0x524/0x1c60 [ 0.372294] #1: 90000000087013b8 (rcu_read_lock){....}-{1:3}, at: rt_spin_trylock+0x50/0x140 [ 0.372305] #2: 900000047fffd388 (&zone->lock){+.+.}-{3:3}, at: __rmqueue_pcplist+0x30c/0xea0 [ 0.372314] irq event stamp: 0 [ 0.372316] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [ 0.372322] hardirqs last disabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372329] softirqs last enabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372335] softirqs last disabled at (0): [<0000000000000000>] 0x0 [ 0.372341] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.12.0-rc7+ #1891 [ 0.372346] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022 [ 0.372349] Stack : 0000000000000089 9000000005a0db9c 90000000071519c8 9000000100388000 [ 0.372486] 900000010038b890 0000000000000000 900000010038b898 9000000007e53788 [ 0.372492] 900000000815bcc8 900000000815bcc0 900000010038b700 0000000000000001 [ 0.372498] 0000000000000001 4b031894b9d6b725 00000000055ec000 9000000100338fc0 [ 0.372503] 00000000000000c4 0000000000000001 000000000000002d 0000000000000003 [ 0.372509] 0000000000000030 0000000000000003 00000000055ec000 0000000000000003 [ 0.372515] 900000000806d000 9000000007e53788 00000000000000b0 0000000000000004 [ 0.372521] 0000000000000000 0000000000000000 900000000c9f5f10 0000000000000000 [ 0.372526] 90000000076f12d8 9000000007e53788 9000000005924778 0000000000000000 [ 0.372532] 00000000000000b0 0000000000000004 0000000000000000 0000000000070000 [ 0.372537] ... [ 0.372540] Call Trace: [ 0.372542] [<9000000005924778>] show_stack+0x38/0x180 [ 0.372548] [<90000000071519c4>] dump_stack_lvl+0x94/0xe4 [ 0.372555] [<900000000599b880>] __might_resched+0x1a0/0x260 [ 0.372561] [<90000000071675cc>] rt_spin_lock+0x4c/0x140 [ 0.372565] [<9000000005cbb768>] __rmqueue_pcplist+0x308/0xea0 [ 0.372570] [<9000000005cbed84>] get_page_from_freelist+0x564/0x1c60 [ 0.372575] [<9000000005cc0d98>] __alloc_pages_noprof+0x218/0x1820 [ 0.372580] [<900000000593b36c>] tlb_init+0x1ac/0x298 [ 0.372585] [<9000000005924b74>] per_cpu_trap_init+0x114/0x140 [ 0.372589] [<9000000005921964>] cpu_probe+0x4e4/0xa60 [ 0.372592] [<9000000005934874>] start_secondary+0x34/0xc0 [ 0.372599] [<900000000715615c>] smpboot_entry+0x64/0x6c This is because in PREEMPT_RT kernels normal spinlocks are replaced by rt spinlocks and rt_spin_lock() will cause sleeping. Fix it by disabling NUMA optimization completely for PREEMPT_RT kernels. Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>

…A in a MM [ Upstream commit 091c1dd ] We currently assume that there is at least one VMA in a MM, which isn't true. So we might end up having find_vma() return NULL, to then de-reference NULL. So properly handle find_vma() returning NULL. This fixes the report: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 1 UID: 0 PID: 6021 Comm: syz-executor284 Not tainted 6.12.0-rc7-syzkaller-00187-gf868cd251776 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/30/2024 RIP: 0010:migrate_to_node mm/mempolicy.c:1090 [inline] RIP: 0010:do_migrate_pages+0x403/0x6f0 mm/mempolicy.c:1194 Code: ... RSP: 0018:ffffc9000375fd08 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffc9000375fd78 RCX: 0000000000000000 RDX: ffff88807e171300 RSI: dffffc0000000000 RDI: ffff88803390c044 RBP: ffff88807e171428 R08: 0000000000000014 R09: fffffbfff2039ef1 R10: ffffffff901cf78f R11: 0000000000000000 R12: 0000000000000003 R13: ffffc9000375fe90 R14: ffffc9000375fe98 R15: ffffc9000375fdf8 FS: 00005555919e1380(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005555919e1ca8 CR3: 000000007f12a000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> kernel_migrate_pages+0x5b2/0x750 mm/mempolicy.c:1709 __do_sys_migrate_pages mm/mempolicy.c:1727 [inline] __se_sys_migrate_pages mm/mempolicy.c:1723 [inline] __x64_sys_migrate_pages+0x96/0x100 mm/mempolicy.c:1723 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [akpm@linux-foundation.org: add unlikely()] Link: https://lkml.kernel.org/r/20241120201151.9518-1-david@redhat.com Fixes: 3974388 ("[PATCH] Swap Migration V5: sys_migrate_pages interface") Signed-off-by: David Hildenbrand <david@redhat.com> Reported-by: syzbot+3511625422f7aa637f0d@syzkaller.appspotmail.com Closes: https://lore.kernel.org/lkml/673d2696.050a0220.3c9d61.012f.GAE@google.com/T/ Reviewed-by: Liam R. Howlett <Liam.Howlett@Oracle.com> Reviewed-by: Christoph Lameter <cl@linux.com> Cc: Liam R. Howlett <Liam.Howlett@Oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes

e71e9ee

RevySR merged commit acd247b into revyos:th1520-v6.6-rc5 Oct 15, 2023
1 of 2 checks passed

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes #1

riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes #1

chainsx commented Oct 11, 2023

riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes #1

riscv: dts: th1520, lpi4a: add sdhci and rtl8723ds nodes #1

Conversation

chainsx commented Oct 11, 2023