Skip to content

Hardware design to facility prototyping Tracker One designs on the Tracker Evaluation Board

License

Notifications You must be signed in to change notification settings

rickkas7/M8-Eval-Adapter

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

5 Commits
 
 
 
 
 
 
 
 
 
 

Repository files navigation

M8-Eval-Adapter

Hardware design to facilitate prototyping Tracker One designs on the Tracker SoM Evaluation Board

Main Image

This is a simple board you can assemble that makes it easier to prototype designs that will eventually use the Tracker One or Tracker SoM Carrier Board, using the Tracker SoM Evaluation Board.

It fits on the 40 pin expansion connector on the Tracker SoM Evaluation Board and includes features that are on the Tracker One and Tracker Carrier Board:

  • B8B-PH connector on the board, the same connector as on the Tracker Carrier Board
  • Thermistor (temperature sensor) connected to A0.
  • USER button connected to A1
  • Blue GNSS LED connected to A2
  • CAN connection

The CAN connection is necessary because CAN is not exposed on the 40-pin header. Short wires connect to the screw terminals on the Tracker SoM evaluation board so the CAN will be available on the M8 connector.

Note: The Tracker One supports up to 30V on the M8 connector. This adapter board does not have the same power supply as the Tracker One and Tracker Carrier Board. This adapter board only supports up to 12V using the B8B-PH as a power input!

About the M8 and B8B-PH Connector

Diagram of inside cable

The Tracker Carrier Board in the Tracker One has a B8B-PH connector on the board.

The Tracker One has a small cable with a PHR-8 connector (fits into the B8B-PH) on one end and an M8 8-pin male IP67 on the other. The M8 end fits into a hole in the case. This is the cable inside the Tracker One:

Cable inside Tracker One

Your Tracker One project will typically use a M8 8-pin female cable. Here's one that has wires on the other end.

M8 to Wires

You'd typically connect those wires to your custom expansion board using one of several methods:

  • Terminate with pins in a PHR-8 to mate with a B8B-PH on your expansion board
  • Terminate with screw terminals on your board
  • Terminate by soldering the wires to your board

For prototyping, you can just skip the M8 cable and use PHR-8 to wires, or a PHR-8 to PHR-8 cable, as in this example:

PHR-8

Design

Schematic

Schematic

Board

Board

The Eagle CAD files (.sch and .brd) are in the Github repository, along with the Gerber files.

BoM (Bill of Materials)

Quan Part Example Price
1 100K NTC Thermistor Panasonic ERT-J1VR104FM $0.39
2 100 ohm resistor 0603 Panasonic ERJ-3GEYJ101V
1 100K resistor 0603 Panasonic ERJ-3EKF1003V
1 Blue LED 0603 Lite-On LTST-C193TBKT-5A $0.47
1 4.5mm momentary switch E Switch TL3305AF160QG $0.20
1 B8B-PH Connector JST B8B-PH-SM4-TB(LF)(SN) $1.00
Male header pins 0.1" Sullins PRPC040SAAN-RC

Assembly Diagram

Assembly

Enabling Firmware Features

To enable these features in the Tracker Edge firmware, edit tracker_config.h and make sure these are defined. They default to not being defined on the Tracker SoM Evaluation board.

#define TRACKER_THERMISTOR                    (A0)
#define TRACKER_USER_BUTTON                   (A1)
#define TRACKER_GNSS_LOCK_LED                 (A2)

About

Hardware design to facility prototyping Tracker One designs on the Tracker Evaluation Board

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published