This library is a fork of ArduinoBLE library to add the support of STM32WB, SPBTLE-RF, SPBTLE-1S, BLUENRG-M2SP, BLUENRG-LP and BLUENRG-M0 BLE modules.
It was successfully tested with the NUCLEO-WB15CC, P-NUCLEO-WB55RG, STM32WB5MM-DK, X-NUCLEO-IDB05A2 or X-NUCLEO-IDB05A1 or X-NUCLEO-BNRG2A1 expansion board and a NUCLEO-F401RE or NUCLEO-L476RG or NUCLEO-L053R8, with B-L475E-IOT01A, B-L4S5I-IOT01A, STEVAL-MKSBOX1V1, STEVAL-MKBOXPRO and with STM32L562E-DK.
- In order to use this library with SM32WBxx series, you need to update the STM32WB Copro Wireless Binaries with stm32wbxx_BLE_HCILayer_fw.bin depending of your mcu:
Each subdirectories contains binaries and Release_Notes.html which explain how to update it.
- In order to use this library with STEVAL-MKSBOX1V1, you need to update the firmware of the SPBTLE-1S BLE module mounted on that board as described in the following wiki page:
- In order to use this library with X-NUCLEO-BNRG2A1, you need to update the firmware of the BLUENRG-M2SP BLE module mounted on that expansion board as described in the following wiki page:
For more information about ArduinoBLE library please visit the official web page at: https://www.arduino.cc/en/Reference/ArduinoBLE
STM32Cube_WPAN has several configuration options, which are set in the app_conf.h.
This package has a default configuration named app_conf_default.h.
The user can include the file app_conf_custom.h to customize the BLE application.
Options wrapped in #ifndef, #endif in app_conf_default.h can be overwritten.
Additional options can be added.
The user can refer to AN5270
The user can change the Tx Power by redefining CFG_TX_POWER using the build_opt.h file. Possible values are listed in the chapter
4.2 Tx power level, default value is 0x18(-0.15dBm). To set it at +1dBm, CFG_TX_POWER have to be defined at 0x1A:
-DCFG_TX_POWER=0x1A
The user can include the file ble_spi_conf.h to define which shield and configuration to use from the following list:
- X-NUCLEO-IDB05A2
IDB05A2_SPI_CLOCK_D3: SPI clock on D3IDB05A2_SPI_CLOCK_D13SPI clock on D13
- X-NUCLEO-IDB05A1
IDB05A1_SPI_CLOCK_D3: SPI clock on D3IDB05A1_SPI_CLOCK_D13: SPI clock on D13
- X-NUCLEO-BNRG2A1
BNRG2A1_SPI_CLOCK_D3: SPI clock on D3BNRG2A1_SPI_CLOCK_D13: SPI clock on D13
CUSTOM_BLE_SPI: define a custom configuration, it requires below definition:BLE_SPI_MISO: SPI MISO pinBLE_SPI_MOSI: SPI MOSI pinBLE_SPI_CLK: SPI CLocK pinBLE_SPI_CS: SPI Chip Select pinBLE_SPI_IRQ: SPI IRQ pinBLE_SPI_FREQ: SPI bus frequencyBLE_SPI_MODE: can be one of the belowSPIMode:SPI_MODE0SPI_MODE1SPI_MODE2SPI_MODE0
BLE_CHIP_TYPE: can be one of the belowBLEChip_t:SPBTLE_RFSPBTLE_1SBLUENRG_M2SPBLUENRG_M0BLUENRG_LP
BLE_RESET: BLE reset pin
To use the X-NUCLEO-IDB05A2 with SPI clock on D3, define in ble_spi_conf.h:
#define IDB05A2_SPI_CLOCK_D3This is equivalent to the below configuration using the CUSTOM_BLE_SPI:
#define CUSTOM_BLE_SPI
#define BLE_SPI_MISO D12
#define BLE_SPI_MOSI D11
#define BLE_SPI_CLK D3
#define BLE_SPI_CS A1
#define BLE_SPI_IRQ A0
#define BLE_SPI_FREQ 8000000
#define BLE_SPI_MODE SPI_MODE0
#define BLE_CHIP_TYPE BLUENRG_M0
#define BLE_RESET D7If required, user can use a compatible BLE module over SPI.
In the ble_spi_conf.h, define USE_BLE_SPI.
Copyright (c) 2019 STMicroelectronics. All rights reserved.
Copyright (c) 2019 Arduino SA. All rights reserved.
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA