-
Notifications
You must be signed in to change notification settings - Fork 272
Operation
There are two main operating modes, "Live scanner" and "Play files"
Usage: dsd [options] Live scanner mode
Live Scanner mode takes 48KHz/16 bit mono audio samples from a sound card input and decodes speech in real time. Options are provided for controling information display and saving mbe data files.
The synthesized speech can be output to a soundcard and/or a .wav file.
Usage: dsd [options] -r <files> Read/Play saved mbe data from file(s)
Play files mode reads mbe data from files specified on the command
line (including wildcards) and synthesizes speech from those files.
The synthesized speech can be output to a soundcard and/or a
.wav file. The -r command line options is used to activate Play files
mode.
There are two main display modes in Live scanner mode. "Errorbars" and "Datascope".
Errorbars mode output for P25 Phase 1 looks like this:
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 0 tg: 32464 TDULC
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 0 tg: 32464 TDULC
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 0 tg: 32464 TDULC
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 0 tg: 32464 TDULC
Sync: -P25p1 mod: C4FM inlvl: 38% nac: 5C2 src: 0 tg: 32464 TDU
Sync: -P25p1 mod: C4FM inlvl: 38% nac: 5C2 src: 0 tg: 32464 HDU
Sync: -P25p1 mod: C4FM inlvl: 42% nac: 5C2 src: 0 tg: 32464 LDU1 e:
Sync: (-P25p1) mod: C4FM inlvl: 39% nac: 5C2 src: 52610 tg: 32464 (LDU2) e:
Sync: -P25p1 mod: C4FM inlvl: 38% nac: 5C2 src: 52610 tg: 32464 LDU1 e:
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 52610 tg: 32464 LDU2 e:
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 52610 tg: 32464 LDU1 e:
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 52610 tg: 32464 LDU2 e:
Sync: -P25p1 mod: C4FM inlvl: 39% nac: 5C2 src: 52610 tg: 32464 LDU1 e:
-
"Sync" indicates the frame type detected and whether the polarity is positive or negative. DSD automatically detects and handles either polarity except for DMR/MOTOTRBO/X2-TDMA which unfortunatley use both sync polarities.
-
Most combinations of transmitter, receiver and soundcard show netagive (-) polarity for X2-TDMA signals and (+) polarity for DMR/MOTOTRBO so those are the defaults.
- You may need to use the
-xoption to select non-inverted polarity if you are not getting usable X2-TDMA/MOTOTRBO/DMR speech. As they use both normal and inverted sync it is not possible to detect polariy automatically.
- You may need to use the
-
"mod" indicates the current demodulation optimizations.
-
"inlvl" indicates the audio input level. QPSK signals tend to appear much "wider" than C4FM from a discriminator tap so it is important to set your input gain using a QPSK signal if you plan to montir them. It is not necessary nor desirable to get to 100%, in fact your sound card may max out below 100%. It is best to use the Datascope mode for setting input gain (see below). Typical values with good results are 40% for C4FM and 66% for QPSK.
-
"nac" is the P25 Phase 1 Network Access Code. This is a 12 bit field in each P25 Phase 1 header. It should not be confused with the 16 bit System ID used in non-P25 trunking control channels.
-
"src" is the radio id of the trasmitting subscriber unit.
-
"tg" is the talkgroup derived from link control information.
-
"HDU/LDU1/LDU2/TDU/TDULC" are P25 Phase 1 frame types, referred to as frame subtype within DSD.
-
"e:" is the beginning of the errorbars display. Each "=" indicates a detected error within the voice data. "R" and "M" indicat that a voice frame was repeated or muted due to excessive errors.
-
Values in parentheses () indicate an assumption (soft decision) was made based on the previous frame.
Errorbars mode output for X2-TDMA looks like this:
Sync: -X2-TDMA mod: QPSK inlvl: 59% src: 17211 tg: 197 [SLOT0] slot1 VOICE e:
Sync: -X2-TDMA mod: QPSK inlvl: 47% src: 17211 tg: 197 [SLOT0] slot1 VOICE e:
Sync: -X2-TDMA mod: QPSK inlvl: 43% src: 17211 tg: 197 [SLOT0] slot1 VOICE e:
Sync: (-X2-TDMA) mod: QPSK inlvl: 28% src: 17211 tg: 197 [SLOT0] slot1 VOICE e:
DMR/MOTOTRBO display is similar except it does not yet show source and talkgroup information.
As of version 1.2 DSD shows which specific TDMA slots are active (with capital SLOT letters) and which slot is currently being monitored (with square brackets []. Noisy/degraded signals will affect the accuracy of this display.
The frame subtypes (Voice/LC etc) are shown based on the DMR standard types.
Datascope mode output looks like this:
Demod mode: C4FM Nac: 8C3
Frame Type: P25 Phase 1 Talkgroup: 16528
Frame Subtype: LDU1 Source: 0
TDMA activity: slot0 slot1 Voice errors:
+----------------------------------------------------------------+
| # ^ !| ^ # |
| * | * |
| * | * |
| * | * * |
| * * | * * |
| * * | ** * |
| * ** | ** * |
| ** ** | ** * |
| ** ** | ** * |
| ** ** | ** * |
+----------------------------------------------------------------+
C4FM Example
Demod mode: C4FM Nac: 126
Frame Type: P25 Phase 1 Talkgroup: 25283
Frame Subtype: LDU2 Source: 0
TDMA activity: slot0 slot1 Voice errors:
+----------------------------------------------------------------+
| # ^ ! ^ # |
| * | |
| * | |
| ** | |
| ** | * |
| * ** | * * |
| ** ** | * * |
| *** ** | ** * |
| *** ** | *** * |
| *** **** | **** * * |
+----------------------------------------------------------------+
QPSK Example
At the top is various information about the signal, similar to the information provided in Errorbars mode. The large box is similar to a spectrum analyzer viewing the channel bandwidth.
The horizontal axis is the input audio level, minimum on the left and maximum on the right. The vertical axis is the number of samples seend at each audio level.
The "*" symbols represent the number of audio
samples that were at each level during the aggregation period.
(default = 36 symbols) The -S options controls the aggregation period
as well as the QPSK tracking symbol buffer, so changing that will affect
QPSK performance as well as the Datascope display.
As you can see from the figures above, clean C4FM signals tend to have four very sharply defined audio levels. The datascope pattern also tends to be faily stable with minor shifts left and right as the receiver tries to frequency track any DC offset.
QPSK signals on the other hand tend to appear much broader (and artifact of how they are distored by FM PLL discriminators). They also tend to vary wildly in width and centering. This is especially true when monitoring simulcast systems. Muliple QPSK signals interfere much more dramatically with an FM discriminator than C4FM signals.
For this reason it is important to isolate your receiver to one
transmitter tower, _especially_ for QPSK signals.
The "#" symbols indicate the detected min/max values that are used
to calibrate the symbol decision points. These are indicated by
"!" for the center decision point and "^" for the mid decision points.
There are several options to control the type and quantity of information displayed in Errorbars mode:
-e Show Frame Info and errorbars (default)
-pe Show P25 encryption sync bits
-pl Show P25 link control bits
-ps Show P25 status bits and low speed data
-pt Show P25 talkgroup info
-q Don't show Frame Info/errorbars
-s Datascope (disables other display options)
-t Show symbol timing during sync
-v <num> Frame information Verbosity
-z <num> Frame rate for datascope
Most of these options are self explanitory. Symbol timing is a noisy option that allows you to view the quality of the frame sync samples and accuracy of the symbol timing adjustments.
Symbol Timing display looks like this:
Symbol Timing:
----------
----------
----------
----------
----------
-+++++++++ 1
+---------- 0
----------
++++++++++ 0
++++++++++
---------- 0
----------
++++++++++ 0
++++++++++
++++++++++
++++++++++
---------- 0
++++++++++ 0
---------- 0
++++++++++ 0
++++++++++
++++++++++
++++++++++
++++++++++
C4FM example
Symbol Timing:
+---------
----------
----------
----------
-----X---- 5
--+++O++++- 4
----------
----X----- 4
++++O++--- 4
--++O++++- 4
----X----- 4
----------
++++O+++-- 4
-+++O+++-- 4
--++O+++-- 4
--++O+++-- 4
----------
++++O++++- 4
----------
++++O+++-- 4
-+++O++++- 4
-+++O+++++ 4
-+++O++--- 4
--++O+++-- 4
QPSK example
Symbol timing is only displayed for symbols during the frame sync period. Each horizontal line represents the 10 audio samples for each symbol. "-" indicates an audio sample below the center reference level and "+" represents a sample above center. "X" indicates a low spike below a reference threshold (reference minimum for C4FM and 80% of reference minimum for QPSK). "O" represents a high spike above the high reference threshold. The numbers to the right indicate which sample position the targeted transition occurred (+/- for C4FM or spike high/low for QPSK). The number of audio samples for the next symbol are adjusted to get this value closer to the target (0 for C4FM and 4 for QPSK). This shows how DSD maintains accurate symbol timing. Symbol timing adjustments are only made during sync, which is the only time reliable transitions can be observed.
In both examples above the symbol timing was off by one sample at the beginning of the frame sync period and was adjusted. Generally if you see any spike values "X/O" in C4FM mode, or lots of them in QPSK mode it indicates noise on the input signal.
-i <device/file> Audio input device/file (default is /dev/audio, - for piped stdin)
-o <device> Audio output device (default is /dev/audio)
-d <dir> Create mbe data files, use this directory, trailing slash required
-r <files> Read/Play saved mbe data from file(s)
-g <num> Audio output gain (default = 0 = auto)
-n Do not send synthesized speech to audio output device
-w <file> Output synthesized speech to a .wav file
-a Display port audio devices
The audio in device can be a sound card OR a .wav file OR a pipe if the file or piped data is in the exact format 48k/16bits/mono/pcm. Audio in should be an unfilterd discriminator tap signal, or can be piped directly from the network output of (e.g.) gqrx with:
socat udp-listen:7355 - | dsd -i - -o pa:2
The audio out device should be a sound card (use the -w options to
output to a .wav file).
Note: On modern linux distributions /dev/audio no longer exists, it is
advised to use PortAudio instead. Query your available devices with the
-a option. Then use the device number with the pa: prefix when
specifying input/output devices, i.e. dsd -i pa:1 -o pa:2.
If the audio in device is the same as the audio out device, the synthesized speech has to be upsampled to the 48k sample rate required for input. A fast upsample function is provided but still leaves some artifacts.
The best sound and minimum cpu usage is achieved with separate sound
cards for input and output
If you specify different input/output devices DSD will use 8k as the output sample rate and the lack of resampling results in much better audio as well as lowe cpu consumption.
If you are using onboard "AC97" sound device you may find that DSD uses much more cpu than expected, in some cases more than is available. This is because many AC97 sound devices are designed to rely on CPU processing power instead of hardware. You may also find that 8k sample rate output is upsampled in the driver using a very basic algorithim resulting in severe distortion. The solution is to use a real hardware sound device (pci card, usb device etc).
As of version 1.2 DSD now automatically levels the output audio. This greately improves readability and eliminates the painful effects of noise bursts. You can specify a fixed audio output gain with the -g option.
-B <num> Serial port baud rate (default=115200)
-C <device> Serial port for scanner control (default=/dev/ttyUSB0)
-R <num> Resume scan after <num> TDULC frames or any PDU or TSDU
On some P25 systems Packet Data Units (PDU) are sent on the same
frequencies used for voice traffic. If done constantly this can
be a severe hinderance to scanning the system in conventional
mode. The -R option enables sending a "resume scan" command to
a scanner connected to a serial port. Use -B and -C to set the baud
rate and serial port device if necessary.
-fa Auto-detect frame type (default)
-f1 Decode only P25 Phase 1
-fd Decode only D-STAR*
-fi Decode only NXDN48* (6.25 kHz) / IDAS*
-fn Decode only NXDN96 (12.5 kHz)
-fp Decode only ProVoice*
-fr Decode only DMR/MOTOTRBO
-fx Decode only X2-TDMA
-l Disable Filters (not recommended)
-ma Auto-select modulation optimizations (default)
-mc Use only C4FM modulation optimizations
-mg Use only GFSK modulation optimizations
-mq Use only QPSK modulation optimizations
-pu Unmute Encrypted P25
-u <num> Unvoiced speech quality (default=3)
-xx Expect non-inverted X2-TDMA signal
-xr Expect inverted DMR/MOTOTRBO signal
* denotes frame types that cannot be auto-detected.
ProVoice and NXDN48 not auto-detected as use different symbol rates (9600 and 2400) than most formats (4800).
MBE speech synthesis is broken down into two main types of sounds, "Voiced" and "Unvoiced". Voiced speech bands are synthesized with a single sine wave centered in the frequency band with the appropriate phase and amplitude.
Unvoiced speech is supposed to be generated with a noise source, 256
point DFT a number of band filters, followed by a 256 point inverse DFT.
For computational simplicity mbelib uses a different method. For each
unvoiced speech band, a number of sine waves are generated, each with a
different random initial phase. The number of waves used per band is
controlled by the -u option. A setting of 4 would approximate the
performance of the 256 point DFT method as the maximum number of voice
bands is 56, and very low frequencies are not synthesized. Values less
than 3 have a noticable lack of unvoiced speech and/or artifacts. The
defualt of 3 provides good speech quality with reasonable cpu use.
Increasing the quality above the default rapidly consumes more CPU for
increasingly diminishing returns.
-A <num> QPSK modulation auto detection threshold (default=26)
-S <num> Symbol buffer size for QPSK decision point tracking
(default=36)
-M <num> Min/Max buffer size for QPSK decision point tracking
(default=15)
Decryption of speech is NOT supported, even if you lawfully posess the encryption keys. Decryption support will not be added in the future as the authors wish to steer as far away from the legal issues associated with encryption as possible.
We realize that there are many legitemate and lawful uses of decryption
software including system/interoperability testing and lawful monitoring.
This software is distributed under a liberal BSD license so there is
nothing to stop others from supplying patches, forking this project or
incorporating it into a commercial product and adding decryption support.
There is support for displaying the encryption sync bits transmitted in
the clear on P25 Phase 1 systems. These bits do not allow for the
decryption of signals without the secret encryption keys. The
encryption sync bits are useful for determining whether a signal is
encrypted vs merely noisy or degraded. As the encryption sync bits
typically include long strings of zeros when a transmission is not
encrypted they can also be used to visually estimate bit error rates.