Merge pull request #42 from MarlinFirmware/bugfix-2.0.x

sync Bugfix 2.0.x
thinkyhead · Jul 8, 2019 · 698e752 · 698e752
2 parents 4aa70f2 + 8b81c0e
commit 698e752
Show file tree

Hide file tree

Showing 486 changed files with 5,481 additions and 2,156 deletions.
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
@@ -312,22 +312,20 @@
 // @section machine
 
 /**
- * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
+ * Power Supply Control
  *
- * 0 = No Power Switch
- * 1 = ATX
- * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
- *
- * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' }
+ * Enable and connect the power supply to the PS_ON_PIN.
+ * Specify whether the power supply is active HIGH or active LOW.
  */
-#define POWER_SUPPLY 0
+//#define PSU_CONTROL
+//#define PSU_NAME "Power Supply"
+
+#if ENABLED(PSU_CONTROL)
+  #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2)
 
-#if POWER_SUPPLY > 0
-  // Enable this option to leave the PSU off at startup.
-  // Power to steppers and heaters will need to be turned on with M80.
-  //#define PS_DEFAULT_OFF
+  //#define PS_DEFAULT_OFF      // Keep power off until enabled directly with M80
 
-  //#define AUTO_POWER_CONTROL        // Enable automatic control of the PS_ON pin
+  //#define AUTO_POWER_CONTROL  // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS           // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
@@ -337,7 +335,6 @@
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU over this temperature
     #define POWER_TIMEOUT 30
   #endif
-
 #endif
 
 // @section temperature
@@ -362,6 +359,7 @@
  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
  *   501 : 100K Zonestar (Tronxy X3A) Thermistor
+ *   512 : 100k RPW-Ultra hotend thermistor (4.7k pullup)
  *     6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
  *     7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
  *    71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
@@ -398,7 +396,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  *
- * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
+ * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" }
  */
 #define TEMP_SENSOR_0 1
 #define TEMP_SENSOR_1 0

diff --git a/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp b/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp
@@ -55,7 +55,7 @@ void spiBegin(void) {
   #endif
 }
 
-#if DISABLED(SOFTWARE_SPI, FORCE_SOFT_SPI)
+#if NONE(SOFTWARE_SPI, FORCE_SOFT_SPI)
 
   //------------------------------------------------------------------------------
   // Hardware SPI
@@ -173,7 +173,7 @@ void spiBegin(void) {
     // Invert the SPI2X bit
     clockDiv ^= 0x1;
 
-    SPCR = _BV(SPE) | _BV(MSTR) | ((bitOrder == SPI_LSBFIRST) ? _BV(DORD) : 0) |
+    SPCR = _BV(SPE) | _BV(MSTR) | ((bitOrder == LSBFIRST) ? _BV(DORD) : 0) |
       (dataMode << CPHA) | ((clockDiv >> 1) << SPR0);
     SPSR = clockDiv | 0x01;
   }

diff --git a/Marlin/src/HAL/HAL_AVR/pinsDebug.h b/Marlin/src/HAL/HAL_AVR/pinsDebug.h
@@ -400,4 +400,4 @@ static void pwm_details(uint8_t pin) {
 
 #endif
 
-#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer);} while (0)
+#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0)
diff --git a/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp b/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp
@@ -34,7 +34,7 @@
 #include "../shared/persistent_store_api.h"
 #include "../../inc/MarlinConfig.h"
 
-#if ENABLED(EEPROM_SETTINGS) && DISABLED(I2C_EEPROM, SPI_EEPROM)
+#if ENABLED(EEPROM_SETTINGS) && NONE(I2C_EEPROM, SPI_EEPROM)
 
 #include "../shared/Marduino.h"
 

diff --git a/Marlin/src/HAL/HAL_DUE/G2_PWM.h b/Marlin/src/HAL/HAL_DUE/G2_PWM.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * This module is stripped down version of the LPC1768_PWM.h file from

diff --git a/Marlin/src/HAL/HAL_DUE/SanityCheck.h b/Marlin/src/HAL/HAL_DUE/SanityCheck.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * Test Arduino Due specific configuration values for errors at compile-time.

diff --git a/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp
@@ -29,7 +29,7 @@
 #include "../../inc/MarlinConfig.h"
 #include "../shared/persistent_store_api.h"
 
-#if DISABLED(I2C_EEPROM, SPI_EEPROM)
+#if NONE(I2C_EEPROM, SPI_EEPROM)
   #define E2END 0xFFF // Default to Flash emulated EEPROM size (EepromEmulation_Due.cpp)
 #endif
 
@@ -38,7 +38,7 @@ extern void eeprom_flush(void);
 bool PersistentStore::access_start() { return true; }
 
 bool PersistentStore::access_finish() {
-  #if DISABLED(I2C_EEPROM, SPI_EEPROM)
+  #if NONE(I2C_EEPROM, SPI_EEPROM)
     eeprom_flush();
   #endif
   return true;

diff --git a/Marlin/src/HAL/HAL_DUE/pinsDebug.h b/Marlin/src/HAL/HAL_DUE/pinsDebug.h
@@ -63,8 +63,8 @@
 #define digitalRead_mod(p) extDigitalRead(p)  // AVR digitalRead disabled PWM before it read the pin
 #define PRINT_PORT(p)
 #define NAME_FORMAT(p) PSTR("%-##p##s")
-#define PRINT_ARRAY_NAME(x)  do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0)
-#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%02d"), p); SERIAL_ECHO(buffer);} while (0)
+#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0)
+#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%02d"), p); SERIAL_ECHO(buffer); }while(0)
 #define GET_ARRAY_PIN(p) pin_array[p].pin
 #define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital
 #define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL ? 1 : 0)

diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp
@@ -66,14 +66,6 @@
 
 #include "../../Marlin.h"
 
-#define SPI_FULL_SPEED      0
-#define SPI_HALF_SPEED      1
-#define SPI_QUARTER_SPEED   2
-#define SPI_EIGHTH_SPEED    3
-#define SPI_SIXTEENTH_SPEED 4
-#define SPI_SPEED_5         5
-#define SPI_SPEED_6         6
-
 void spiBegin();
 void spiInit(uint8_t spiRate);
 void spiSend(uint8_t b);

diff --git a/Marlin/src/HAL/HAL_ESP32/FlushableHardwareSerial.h b/Marlin/src/HAL/HAL_ESP32/FlushableHardwareSerial.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 #ifdef ARDUINO_ARCH_ESP32
 

diff --git a/Marlin/src/HAL/HAL_ESP32/SanityCheck.h b/Marlin/src/HAL/HAL_ESP32/SanityCheck.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 #if ENABLED(EMERGENCY_PARSER)
   #error "EMERGENCY_PARSER is not yet implemented for ESP32. Disable EMERGENCY_PARSER to continue."

diff --git a/Marlin/src/HAL/HAL_ESP32/servotimers.h b/Marlin/src/HAL/HAL_ESP32/servotimers.h
@@ -19,3 +19,4 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
diff --git a/Marlin/src/HAL/HAL_LINUX/SanityCheck.h b/Marlin/src/HAL/HAL_LINUX/SanityCheck.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * Test X86_64-specific configuration values for errors at compile-time.

diff --git a/Marlin/src/HAL/HAL_LINUX/main.cpp b/Marlin/src/HAL/HAL_LINUX/main.cpp
@@ -49,7 +49,7 @@ void write_serial_thread() {
 void read_serial_thread() {
   char buffer[255] = {};
   for (;;) {
-    std::size_t len = MIN(usb_serial.receive_buffer.free(), 254U);
+    std::size_t len = _MIN(usb_serial.receive_buffer.free(), 254U);
     if (fgets(buffer, len, stdin))
       for (std::size_t i = 0; i < strlen(buffer); i++)
         usb_serial.receive_buffer.write(buffer[i]);

diff --git a/Marlin/src/HAL/HAL_LINUX/pinsDebug.h b/Marlin/src/HAL/HAL_LINUX/pinsDebug.h
@@ -33,8 +33,8 @@
 #define PRINT_PORT(p)
 #define GET_ARRAY_PIN(p) pin_array[p].pin
 #define NAME_FORMAT(p) PSTR("%-##p##s")
-#define PRINT_ARRAY_NAME(x)  do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0)
-#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer);} while (0)
+#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0)
+#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0)
 #define MULTI_NAME_PAD 16 // space needed to be pretty if not first name assigned to a pin
 
 // active ADC function/mode/code values for PINSEL registers

diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL_Servo_LPC1768.h b/Marlin/src/HAL/HAL_LPC1768/HAL_Servo_LPC1768.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * servo.h - Interrupt driven Servo library for Arduino using 16 bit timers- Version 2

diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp
@@ -162,7 +162,7 @@
     // setup for SPI mode
     SSP_CFG_Type HW_SPI_init; // data structure to hold init values
     SSP_ConfigStructInit(&HW_SPI_init);  // set values for SPI mode
-    HW_SPI_init.ClockRate = Marlin_speed[MIN(spiRate, 6)]; // put in the specified bit rate
+    HW_SPI_init.ClockRate = Marlin_speed[_MIN(spiRate, 6)]; // put in the specified bit rate
     HW_SPI_init.Mode |= SSP_CR1_SSP_EN;
     SSP_Init(LPC_SSPn, &HW_SPI_init);  // puts the values into the proper bits in the SSP0 registers
   }

diff --git a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h b/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * Test LPC176x-specific configuration values for errors at compile-time.

diff --git a/Marlin/src/HAL/HAL_LPC1768/include/SPI.h b/Marlin/src/HAL/HAL_LPC1768/include/SPI.h
@@ -19,7 +19,6 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
-
 #pragma once
 
 #include "../../shared/HAL_SPI.h"

diff --git a/Marlin/src/HAL/HAL_LPC1768/persistent_store_api.h b/Marlin/src/HAL/HAL_LPC1768/persistent_store_api.h
@@ -19,6 +19,8 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
+
 #include "../shared/persistent_store_api.h"
 
 #define FLASH_EEPROM_EMULATION
diff --git a/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h b/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h
@@ -33,8 +33,8 @@
 #define PRINT_PORT(p)
 #define GET_ARRAY_PIN(p) pin_array[p].pin
 #define NAME_FORMAT(p) PSTR("%-##p##s")
-#define PRINT_ARRAY_NAME(x)  do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0)
-#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%d.%02d"), LPC1768_PIN_PORT(p), LPC1768_PIN_PIN(p)); SERIAL_ECHO(buffer);} while (0)
+#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0)
+#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%d.%02d"), LPC1768_PIN_PORT(p), LPC1768_PIN_PIN(p)); SERIAL_ECHO(buffer); }while(0)
 #define MULTI_NAME_PAD 16 // space needed to be pretty if not first name assigned to a pin
 
 // pins that will cause hang/reset/disconnect in M43 Toggle and Watch utilities

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_I2C_routines.h b/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_I2C_routines.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 void u8g_i2c_init(uint8_t options);
 uint8_t u8g_i2c_wait(uint8_t mask, uint8_t pos);

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_defines.h b/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_defines.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * LPC1768 LCD-specific defines

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_delay.h b/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_delay.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * LCD delay routines - used by all the drivers.

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_pin_routines.h b/Marlin/src/HAL/HAL_LPC1768/u8g/HAL_LCD_pin_routines.h
@@ -19,6 +19,7 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
  */
+#pragma once
 
 /**
  * Low level pin manipulation routines - used by all the drivers.

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_hw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_hw_spi.cpp
@@ -59,16 +59,8 @@
 
 #if HAS_GRAPHICAL_LCD
 
-//#include <inttypes.h>
 #include <U8glib.h>
-
-#define SPI_FULL_SPEED 0
-#define SPI_HALF_SPEED 1
-#define SPI_QUARTER_SPEED 2
-#define SPI_EIGHTH_SPEED 3
-#define SPI_SIXTEENTH_SPEED 4
-#define SPI_SPEED_5 5
-#define SPI_SPEED_6 6
+#include "../../shared/HAL_SPI.h"
 
 void spiBegin();
 void spiInit(uint8_t spiRate);

diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp
@@ -59,18 +59,10 @@
 
 #if HAS_GRAPHICAL_LCD
 
-//#include <inttypes.h>
 #include <U8glib.h>
+#include "../../shared/HAL_SPI.h"
 #include "../../shared/Delay.h"
 
-#define SPI_FULL_SPEED 0
-#define SPI_HALF_SPEED 1
-#define SPI_QUARTER_SPEED 2
-#define SPI_EIGHTH_SPEED 3
-#define SPI_SIXTEENTH_SPEED 4
-#define SPI_SPEED_5 5
-#define SPI_SPEED_6 6
-
 void spiBegin();
 void spiInit(uint8_t spiRate);
 void spiSend(uint8_t b);

diff --git a/Marlin/src/HAL/HAL_STM32/HAL.h b/Marlin/src/HAL/HAL_STM32/HAL.h
@@ -132,7 +132,7 @@
 // Types
 // --------------------------------------------------------------------------
 
-typedef int8_t pin_t;
+typedef int16_t pin_t;
 
 #define HAL_SERVO_LIB libServo
 

diff --git a/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp b/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp
@@ -28,20 +28,20 @@
 
 #include "../shared/persistent_store_api.h"
 
-#if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
+#if NONE(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
   #include <EEPROM.h>
   static bool eeprom_data_written = false;
 #endif
 
 bool PersistentStore::access_start() {
-  #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
+  #if NONE(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
     eeprom_buffer_fill();
   #endif
   return true;
 }
 
 bool PersistentStore::access_finish() {
-  #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
+  #if NONE(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
     if (eeprom_data_written) {
       eeprom_buffer_flush();
       eeprom_data_written = false;
@@ -76,7 +76,7 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, ui
     pos++;
     value++;
   };
-  #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
+  #if NONE(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM)
     eeprom_data_written = true;
   #endif
Original file line number	Diff line number	Diff line change
Expand Up		@@ -400,4 +400,4 @@ static void pwm_details(uint8_t pin) {

		#endif

		#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer);} while (0)
		#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0)
-Original file line number
+Diff line change
@@ Expand Up / @@ -19,6 +19,7 @@ @@
      * along with this program.  If not, see <http://www.gnu.org/licenses/>.
      *
      */
+    #pragma once
     /**
      * This module is stripped down version of the LPC1768_PWM.h file from
@@ Expand Down @@