STM32 UART DMA RX/TX

This is an application note and contains list of examples about 2 distinct topics:

• Receiving data with UART and DMA when application does not know in advance size of bytes to be received
• Transmitting data with UART and DMA to avoid CPU stalling and use CPU for other purposes

Table of Contents

• Abbreviations
• General about UART
• General about DMA
  • Combine UART + DMA for data reception
  • Combine UART + DMA for data transmission
  • DMA HT/TC and UART IDLE combination details
• Examples
  • Examples for UART + DMA RX
  • Examples for UART DMA for TX
• How to use this repository

Abbreviations

• DMA: Direct Memory Access controller in STM32
• UART: Universal Asynchronous Receiver Transmitter
• USART: Universal Synchronous Asynchronous Receiver Transmitter
• TX: Transmit
• RX: Receive
• HT: Half-Transfer Complete event/flag for DMA
• TC: Transfer Complete event/flag for DMA
• RTO: Receiver Timeout event/flag
• IRQ: Interrupt

General about UART

STM32 has peripherals such as USART and UART. Difference between them is that USART includes advance feature such as optional synchronous communication, not available in UART. If these features are not used, USART and UART peripherals can be considered identical. For the sake of this application note, we will use term UART only, while exactly same applies to USART peripherals aswell.

UART in STM32 allows customers to configure it using different transmit(TX)/receive(RX) modes:

• Polling mode (no DMA, no IRQ)
  • Application is polling for status bits to check if any character has been transmitted/received and read it fast enough in order to not-miss any byte
  • P: Easy to implement
  • C: Easy to miss received characters in bursts
  • C: Works only for low baudrates, 9600 or lower
  • C: Application must periodically (with high frequency) check for new characters, usually not always possible at complex systems
• Interrupt mode (no DMA)
  • UART triggers interrupt and CPU jumps to service routine to handle each received byte separately
  • P: Commonly used approach in embedded applications
  • P: Works well with common baudrates, 115200, up to ~921600 bauds
  • C: Interrupt service routine is executed for every received character
  • C: May stall other tasks in high-performance MCUs if interrupts are triggered for every character
  • C: May stall operating system when receiving burst of data, interrupt priority must be higher than operating system maximum is
• DMA mode
  • DMA is used to transfer data from USART RX data register to user memory on hardware level. No application interaction is needed at this point except processing received data by application once necessary
  • P: Transfer from USART peripheral to memory is done on hardware level without CPU interaction
  • P: Can work very easily with operating systems
  • P: Optimized for highest baudrates > 1Mbps and low-power applications
  • P: In case of big bursts of data, increasing data buffer size can improve functionality
  • C: Number of bytes to transfer must be known in advance by DMA hardware
  • C: If communication fails, DMA may not notify application about all bytes transferred

For RX mode, this article focuses only on DMA mode, to receive unknown number of bytes

Every STM32 has at least one (1) UART IP and at least one (1) DMA controller available in its DNA. For data transmission, no special features (on top of essential one) are necessary, except DMA availability for UART. Application uses use default features to implement very efficient transmit system using DMA.

While it is straight-forward for TX, this is not the case for receive operation. When implementing DMA receive, application would need to understand number of received bytes to process by DMA before finishing transfer. This is especially true when UART is used for system communication where it has to react in short time after all bytes have been received. STM32s have capability in UART to detect when RX line has not been active for period of time. This is achieved using one of 2 available methods:

• IDLE LINE event: Triggered when RX line has been in idle state (normally high state) for 1 frame time, after last received byte. Frame time is based on baudrate. Higher baudrate means lower frame time for single byte.
• RTO (Receiver Timeout) event: Triggered when line has been in idle state for programmable time. It is fully configured by firmware.

Both events can trigger an interrupt which is an essential feature to allow effective receive operation

Not all STM32 have IDLE LINE or RTO features available. When not available, examples concerning these features may not be used.

An example: To transmit 1 byte at 115200 bauds, it takes approximately (for easier estimation) ~100us; for 3 bytes it would be ~300us in total. IDLE line event triggers an interrupt for application when line has been in idle state for 1 frame time (in this case 100us) after third byte has been received.

This is a real experiment demo using STM32F4 and IDLE LINE event. After IDLE event is triggered, data are echoed back (loopback mode):

• Application receives 3 bytes, takes approx ~300us at 115200 bauds
• RX goes to high state (yellow rectangle) and UART RX detects that it has been idle for at least 1 frame time (approx 100us)
  • Width of yellow rectangle represents 1 frame time
• IDLE line interrupt is triggered at green arrow
• Application echoes data back from interrupt

General about DMA

DMA in STM32 can be configured in normal or circular mode. For each mode, DMA requires number of elements to transfer before its events (half-transfer complete, transfer complete) are triggered.

• Normal mode: DMA starts with data transfer, once it transfers all elements, it stops and sets enable bit to 0.
  • Application is using this mode when transmitting data
• Circular mode: DMA starts with transfer, once it transfers all elements (as written in corresponding length register), it starts from beginning of memory and transfers more
  • Applicaton is using this mode when receiving data

While transfer is active, 2 (among others) interrupts may be triggered:

• Half-Transfer complete HT: Triggers when DMA transfers half count of elements
• Transfer-Complete TC: Triggers when DMA transfers all elements

When DMA operates in circular mode, these interrupts are triggered periodically

Number of elements to transfer by DMA hardware must be written to relevant DMA register before start of transfer

Combine UART + DMA for data reception

Now it is time to understand which features to use to receive data with UART and DMA to offload CPU. As for the sake of this example, we use memory buffer array of 20 bytes. DMA will transfer data received from UART to this buffer.

Listed are steps to begin. Initial assumption is that UART has been initialized prior reaching this step, same for basic DMA setup, the rest:

• Application writes 20 to relevant DMA register for data length
• Application writes memory & peripheral addresses to relevant DMA registers
• Application sets DMA direction to peripheral-to-memory mode
• Application puts DMA to circular mode. This is to assure DMA does not stop transferring data after it reaches end of memory. Instead, it will roll over and continue with transferring possible more data from UART to memory
• Application enables DMA & UART in reception mode. Receive can not start & DMA will wait UART to receive first character and transmit it to array. This is done for every received byte
• Application is notified by DMA HT event (or interrupt) after first 10 have been transferred from UART to memory
• Application is notified by DMA TC event (or interrupt) after 20 bytes are transferred from UART to memory
• Application is notified by UART IDLE line (or RTO) in case of IDLE line or timeout detected on RX line
• Application needs to reach on all of these events for most efficient receive

This configuration is important as we do not know length in advance. Application needs to assume it may be endless number of bytes received, therefore DMA must be operational endlessly.

We have used 20 bytes long array for demonstration purposes. In real app this size may need to be increased. It all depends on UART baudrate (higher speed, more data may be received in fixed window) and how fast application can process the received data (either using interrupt notification, RTOS, or polling mode)

Combine UART + DMA for data transmission

Everything gets simplier when application transmits data, length of data is known in advance and memory to transmit is ready. For the sake of this example, we use memory for Helloworld message. In C language it would be:

const char
hello_world_arr[] = "HelloWorld";

• Application writes number of bytes to transmit to relevant DMA register, that would be strlen(hello_world_arr) or 10
• Application writes memory & peripheral addresses to relevant DMA registers
• Application sets DMA direction to memory-to-peripheral mode
• Application sets DMA to normal mode. This effectively disables DMA once all the bytes are successfully transferred
• Application enables DMA & UART in transmitter mode. Transmit starts immediately when UART requests first byte via DMA to be shifted to UART TX register
• Application is notified by TC event (or interrupt) after all bytes have been transmitted from memory to UART via DMA
• DMA is stopped and application may prepare next transfer immediately

Please note that TC event is triggered before last UART byte has been fully transmitted over UART. That's because TC event is part of DMA and not part of UART. It is triggered when DMA transfers all the bytes from point A to point B. That is, point A for DMA is memory, point B is UART data register. Now it is up to UART to clock out byte to GPIO pin

DMA HT/TC and UART IDLE combination details

This section describes 4 possible cases and one additional which explains why HT/TC events are necessary by application

Abbrevations used on image:

• R: Read pointer, used by application to read data from memory. Later also used as old_ptr
• W: Write pointer, used by DMA to write next byte to. Increased every time DMA writes new byte. Later also used as new_ptr
• HT: Half-Transfer Complete event triggered by DMA
• TC: Transfer-Complete event triggered by DMA
• I: IDLE line detection event triggered by USART

DMA configuration:

• Circular mode
• 20 bytes length memory
  • HT event triggers at 10 bytes
  • TC event triggers at 20 bytes

Possible cases:

• Case A: DMA transfers 10 bytes. Application gets notification by HT event and may process received data
• Case B: DMA transfers next 10 bytes. Application gets notification by TC event. Processing now starts from last known position until the end of memory
  • DMA is in circular mode, thus it will continue from beginning of buffer to transfer next byte
• Case C: DMA transfers 10 bytes, but not aligned with HT nor TC events
  • Application gets notification by HT event when first 6 bytes are transfered. Processing may start from last known read location
  • Application gets IDLE event after next 4 bytes are successfully transfered
• Case D: DMA transfers 10 bytes in overflow mode and but not aligned with HT nor TC events
  • Application gets notification by TC event when first 4 bytes are transfered. Processing may start from last known read location
  • Application gets notification by IDLE event after next 6 bytes are transfered. Processing may start from beginning of buffer
• Case E: Example what may happen when application relies only on IDLE event
  • If application receives 30 bytes in burst, 10 bytes get overwritten by DMA as application did not process it quickly enough
  • Application gets IDLE line event once there is steady RX line for 1 byte timeframe
  • Red part of data represents first 10 received bytes from burst which were overwritten by last 10 bytes in burst
  • Option to avoid such scenario is to poll for DMA changes quicker than burst of 20 bytes take; or by using TC and HT events

Example code to read data from memory and process it, for cases A-D

/**
 * \brief           Check for new data received with DMA
 * \note            This function must be called from DMA HT/TC and USART IDLE events
 * \note            Full source code is available in examples
 */
void
usart_rx_check(void) {
    static size_t old_pos;
    size_t pos;

    /* Calculate current position in buffer */
    pos = ARRAY_LEN(usart_rx_dma_buffer) - LL_DMA_GetDataLength(DMA1, LL_DMA_STREAM_1);
    if (pos != old_pos) {                       /* Check change in received data */
        if (pos > old_pos) {                    /* Current position is over previous one */
            /* We are in "linear" mode, case P1, P2, P3 */
            /* Process data directly by subtracting "pointers" */
            usart_process_data(&usart_rx_dma_buffer[old_pos], pos - old_pos);
        } else {
            /* We are in "overflow" mode, case P4 */
            /* First process data to the end of buffer */
            usart_process_data(&usart_rx_dma_buffer[old_pos], ARRAY_LEN(usart_rx_dma_buffer) - old_pos);
            /* Check and continue with beginning of buffer */
            if (pos > 0) {
                usart_process_data(&usart_rx_dma_buffer[0], pos);
            }
        }
    }
    old_pos = pos;                              /* Save current position as old */

    /* Check and manually update if we reached end of buffer */
    if (old_pos == ARRAY_LEN(usart_rx_dma_buffer)) {
        old_pos = 0;
    }
}

Examples

Examples provide reference code to implement RX and TX functionality using DMA transfers. There are 2 sets of examples:

• Examples for RX only
  • Available in projects folder with usart_rx_ prefix
  • DMA is used to receive data, polling is used to echo data back
• Examples for RX & TX
  • Available in projects folder with usart_tx_ prefix
  • DMA is used to receive data and to transmit data back
  • It uses ring buffer to copy data from DMA buffer to application buffer first

Common for all examples:

• Developed in STM32CubeIDE for easier evaluation on STM32 boards
• Fully developed using LL drivers for various STM32 families
• UART common configuration: 115200 bauds, 1 stop bit, no-parity
• DMA RX common configuration: Circular mode, TC and HT events enabled
• DMA TX common configuration: Normal mode, TC event enabled
• All RX examples implement loop-back with polling. Every character received by UART and transfered by DMA is sent back to same UART

STM32 family	Board name	USART	STM32 TX	STM32 RX	RX DMA settings	TX DMA settings
STM32F1xx	BluePill-F103C8	USART1	PA9	PA10	DMA1, Channel 5
STM32F4xx	NUCLEO-F413ZH	USART3	PD8	PD9	DMA1, Stream 1, Channel 4	DMA1, Stream 3, Channel 4
STM32G0xx	NUCLEO-G071RB	USART2	PA2	PA3	DMA1, Channel 1
STM32G4xx	NUCLEO-G474RE	LPUART1	PA2	PA3	DMA1, Channel 1
STM32L4xx	NUCLEO-L432KC	USART2	PA2	PA15	DMA1, Channel 6, Request 2
STM32H7xx	NUCLEO-H743ZI2*	USART3	PD8	PD9	DMA1, Stream 0	DMA1, Stream 1

• It is possible to run H743 (single-core) examples on dual-core STM32H7 Nucleo boards, NUCLEO-H745 or NUCLEO-H755. Special care needs to be taken as dual-core H7 Nucleo boards use DCDC for MCU power hence application must check clock configuration in main file and uncomment code to enable SMPS.

Examples demonstrate different use cases for RX only or RX&TX combined.

Examples for UART + DMA RX

Polling for changes

• DMA hardware takes care to transfer received data to memory
• Application must constantly poll for new changes in DMA registers and read received data quick enough to make sure DMA will not overwrite data in buffer
• Processing of received data is in thread mode (not in interrupt)
• P: Easy to implement
• P: No interrupts, no consideration of priority and race conditions
• P: Fits for devices without USART IDLE line detection
• C: Application takes care of data periodically
• C: Not possible to put application to low-power mode (sleep mode)

Polling for changes with operating system

• Same as polling for changes but with dedicated thread in operating system to process data
• P: Easy to implement to RTOS systems, uses single thread without additional RTOS features (no mutexes, semaphores, memory queues)
• P: No interrupts, no consideration of priority and race conditions
• P: Data processing always on-time with maximum delay given by thread delay, thus with known maximum latency between received character and processed time
  • Unless system has higher priority threads
• P: Fits for devices without UART IDLE line detection
• C: Application takes care of data periodically
• C: Uses memory resources dedicated for separate thread for data processing
• C: Not possible to put application to low-power mode (sleep mode)

UART IDLE line detection + DMA HT&TC interrupts

• Application gets notification by IDLE line detection or DMA TC/HT events
• Application has to process data only when it receives any of the 3 interrupts
• P: Application does not need to poll for new changes
• P: Application receives interrupts on events
• P: Application may enter low-power modes to increase battery life (if operated on battery)
• C: Data are read (processed) in the interrupt. We strive to execute interrupt routine as fast as possible
• C: Long interrupt execution may break other compatibility in the application

Processing of incoming data is from 2 interrupt vectors, hence it is important that they do not preempt each-other. Set both to the same preemption priority!

USART Idle line detection + DMA HT&TC interrupts with RTOS

• Application gets notification by IDLE line detection or DMA TC/HT events
• Application uses separate thread to process the data only when notified in one of interrupts
• P: Processing is not in the interrupt but in separate thread
• P: Interrupt only informs processing thread to process (or to wakeup)
• P: Operating system may put processing thread to blocked state while waiting for event
• C: Memory usage for separate thread + message queue (or semaphore)

This is the most preferred way to use and process UART received character

Examples for UART DMA for TX (and optionally included RX)

• Application is using DMA in normal mode to transfer data
• Application is always using ringbuffer between high-level write and low-level transmit operation
• DMA TC interrupt is triggered when transfer has finished. Application can then send more data

Demo application for debug messages

This is a demo application available in projects folder. Its purpose is to show how can application implement output of debug messages without drastically affect CPU performance. It is using DMA to transfer data (no CPU to wait for UART flags) and can achieve very high or very low data rates

• All debug messages from application are written to intermediate ringbuffer
• Application will try to start & configure DMA after every successfive write to ringbuffer
• If transfer is on-going, next start is configured from DMA TC interrupt

As a result of this demo application for STM32F413-Nucleo board, observations are as following:

• Demo code sends 1581 bytes every second at 115200 bauds, which is approx 142ms.
• With DMA disabled, CPU load was 14%, in-line with time to transmit the data
• With DMA enabled, CPU load was 0%
• DMA can be enabled/disabled with USE_DMA_TX macro configuration in main.c

How to use this repository

1. run git clone --recurse-submodules https://github.com/MaJerle/stm32-usart-dma-rx-tx to clone repository including submodules
2. run examples from projects directory using STM32CubeIDE IDE