net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
 - Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
 - Updated Address Lookup Engine (ALE) module;
 - (TBD) New version of Common platform time sync (CPTS) module.

On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.

Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.

Introduced driver provides standard Linux net_device to user space and supports:
 - ifconfig up/down
 - MAC address configuration
 - ethtool operation:
   --driver
   --change
   --register-dump
   --negotiate phy
   --statistics
   --set-eee phy
   --show-ring
   --show-channels
   --set-channels
 - net_device ioctl mii-control
 - promisc mode

 - rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
   The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
   csum information for each packet in psdata[2] word:
   - BIT(16) CHECKSUM_ERROR - indicates csum error
   - BIT(17) FRAGMENT -  indicates fragmented packet
   - BIT(18) TCP_UDP_N -  Indicates TCP packet was detected
   - BIT(19) IPV6_VALID,  BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
   - BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
   during the checksum computation. This value is FFFFh for non fragmented
   IPV4/6 UDP/TCP packets with no checksum error.

   RX csum offload can be disabled:
	 ethtool -K <dev> rx-checksum on|off

 - tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
   TX csum HW offload  can be enabled/disabled:
	 ethtool -K <dev> tx-checksum-ip-generic on|off

 - multiq and switch between round robin/prio modes for cppi tx queues by
   using Netdev private flag "p0-rx-ptype-rrobin" to switch between
   Round Robin and Fixed priority modes:
	 # ethtool --show-priv-flags eth0
	 Private flags for eth0:
	 p0-rx-ptype-rrobin: on
	 # ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

   Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".

 - GRO support: the napi_gro_receive() and napi_complete_done() are used.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/ti/Kconfig

@@ -6,7 +6,7 @@
 config NET_VENDOR_TI
 	bool "Texas Instruments (TI) devices"
 	default y
-	depends on PCI || EISA || AR7 || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE
+	depends on PCI || EISA || AR7 || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3
 	---help---
 	  If you have a network (Ethernet) card belonging to this class, say Y.
 
@@ -31,7 +31,7 @@ config TI_DAVINCI_EMAC
 
 config TI_DAVINCI_MDIO
 	tristate "TI DaVinci MDIO Support"
-	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST
+	depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
 	select PHYLIB
 	---help---
 	  This driver supports TI's DaVinci MDIO module.
@@ -95,6 +95,21 @@ config TI_CPTS_MOD
 	imply PTP_1588_CLOCK
 	default m
 
+config TI_K3_AM65_CPSW_NUSS
+	tristate "TI K3 AM654x/J721E CPSW Ethernet driver"
+	depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER
+	select TI_DAVINCI_MDIO
+	imply PHY_TI_GMII_SEL
+	help
+	  This driver supports TI K3 AM654/J721E CPSW2G Ethernet SubSystem.
+	  The two-port Gigabit Ethernet MAC (MCU_CPSW0) subsystem provides
+	  Ethernet packet communication for the device: One Ethernet port
+	  (port 1) with selectable RGMII and RMII interfaces and an internal
+	  Communications Port Programming Interface (CPPI) port (port 0).
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ti-am65-cpsw-nuss.
+
 config TI_KEYSTONE_NETCP
 	tristate "TI Keystone NETCP Core Support"
 	select TI_DAVINCI_MDIO

drivers/net/ethernet/ti/Makefile

@@ -23,3 +23,6 @@ obj-$(CONFIG_TI_KEYSTONE_NETCP) += keystone_netcp.o
 keystone_netcp-y := netcp_core.o cpsw_ale.o
 obj-$(CONFIG_TI_KEYSTONE_NETCP_ETHSS) += keystone_netcp_ethss.o
 keystone_netcp_ethss-y := netcp_ethss.o netcp_sgmii.o netcp_xgbepcsr.o cpsw_ale.o
+
+obj-$(CONFIG_TI_K3_AM65_CPSW_NUSS) += ti-am65-cpsw-nuss.o
+ti-am65-cpsw-nuss-y := am65-cpsw-nuss.o cpsw_sl.o am65-cpsw-ethtool.o cpsw_ale.o k3-cppi-desc-pool.o