Skip to content

Actions: Duet3D/RepRapFirmware

Actions

All workflows

Actions

Loading...
Loading

Showing runs from all workflows
201 workflow runs
201 workflow runs

Filter by Event

Filter by Status

Filter by Branch

Filter by Actor

3.5.2 release candidate 1 Upload release assets #12: Release 3.5.2-rc.1 published by dc42
May 31, 2024 08:13 29s
May 31, 2024 08:13 29s
Check for sufficient free memory before allocating a new heap block Auto-close blank templates #216: Issue #1013 opened by dc42
May 28, 2024 08:21 13s
May 28, 2024 08:21 13s
In SBC mode the supported nesting of function calls is too low Auto-close blank templates #215: Issue #1012 opened by dc42
May 24, 2024 08:22 12s
May 24, 2024 08:22 12s
[FeatureRequest] Add M303 cancelling to M108 Auto-close blank templates #214: Issue #1010 opened by droftarts
May 17, 2024 11:55 12s
May 17, 2024 11:55 12s
After adding a driver to a M584 defined axis, motor doesn't move Auto-close blank templates #213: Issue #1009 opened by droftarts
May 17, 2024 10:21 11s
May 17, 2024 10:21 11s
Bug: setting elements of nested arrays sometimes goes wrong Auto-close blank templates #212: Issue #1008 opened by dc42
May 17, 2024 07:25 11s
May 17, 2024 07:25 11s
Extend events to include Fan Tacho Auto-close blank templates #211: Issue #1007 opened by T3P3
May 16, 2024 12:01 11s
May 16, 2024 12:01 11s
Incorrect extruder steps for G2/G3 moves at low extruder steps/mm Auto-close blank templates #210: Issue #1006 opened by T3P3
May 15, 2024 12:07 12s
May 15, 2024 12:07 12s
Task CPU usage in M122 report can exceed 100% Auto-close blank templates #209: Issue #1005 opened by dc42
May 14, 2024 20:54 12s
May 14, 2024 20:54 12s
Pause and resume, during a restartable macro from a job file, restarts the entire job file Auto-close blank templates #208: Issue #1004 opened by T3P3
May 14, 2024 20:54 16s
May 14, 2024 20:54 16s
Bug: can't create a variable with the same name as a parameter Auto-close blank templates #207: Issue #1003 opened by dc42
May 14, 2024 17:26 12s
May 14, 2024 17:26 12s
[FeatureRequest] Add saving of probe and SZP parameters to config-override.g Auto-close blank templates #206: Issue #1002 opened by droftarts
May 13, 2024 16:06 15s
May 13, 2024 16:06 15s
[FeatureRequest] Add M code to configure CAN_0 and CAN_1 on 6HC/6XD Auto-close blank templates #205: Issue #1000 opened by droftarts
May 13, 2024 13:51 14s
May 13, 2024 13:51 14s
[FeatureRequest]: Label the 4 values in the M558.1 report Auto-close blank templates #204: Issue #999 opened by droftarts
May 13, 2024 12:44 15s
May 13, 2024 12:44 15s
Queued commands not executed causing tool change to hang Auto-close blank templates #203: Issue #998 opened by dc42
May 10, 2024 14:06 12s
May 10, 2024 14:06 12s
RRF no longer respects M665 B or H parameters or endstop limits on linear delta printers Auto-close blank templates #202: Issue #997 opened by droftarts
May 10, 2024 12:39 14s
May 10, 2024 12:39 14s
[Bug]: MB6HC (maybe 6XD too) - LED strips connected to io ports set first LED incorrectly, always green Auto-close blank templates #201: Issue #996 opened by droftarts
May 9, 2024 13:11 16s
May 9, 2024 13:11 16s
Large object models cause request issues when M409 and rr_model used at the same time Auto-close blank templates #200: Issue #995 opened by T3P3
May 8, 2024 15:47 12s
May 8, 2024 15:47 12s
[Bug]: Feedrate lower than F1.6 causes no motion and RRF stuck at 'Busy' Auto-close blank templates #199: Issue #994 opened by droftarts
May 7, 2024 11:12 14s
May 7, 2024 11:12 14s
Support XY coordinate offsets in M669 parameters for polar kinematics Auto-close blank templates #198: Issue #993 opened by dc42
May 6, 2024 07:40 11s
May 6, 2024 07:40 11s
Further restrict what gcodes can be run after M112 Auto-close blank templates #197: Issue #992 opened by T3P3
May 3, 2024 15:08 16s
May 3, 2024 15:08 16s
Better support for changing the CAN bit rate Auto-close blank templates #196: Issue #991 opened by dc42
May 2, 2024 11:39 14s
May 2, 2024 11:39 14s
[Bug]: DoLookahead modifies extrusion move followed by z move Auto-close blank templates #195: Issue #990 opened by gloomyandy
April 29, 2024 09:18 11s
April 29, 2024 09:18 11s
[Bug]: High acceleration can cause a very large number of hiccups Auto-close blank templates #194: Issue #989 opened by gloomyandy
April 29, 2024 08:58 13s
April 29, 2024 08:58 13s
[FeatureRequest]: Add M915 parameters to object model Auto-close blank templates #193: Issue #988 opened by owendare
April 28, 2024 05:26 14s
April 28, 2024 05:26 14s