🐛 Use whole PROBE_TEMP_COMPENSATION values (#519)

MarlinFirmware/Marlin#22130
MarlinFirmware · Jun 13, 2021 · 4140399 · 4140399
1 parent f38bfbf
commit 4140399
Show file tree

Hide file tree

Showing 244 changed files with 2,196 additions and 2,196 deletions.
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/ADIMLab/Gantry v1/Configuration_adv.h b/config/examples/ADIMLab/Gantry v1/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/ADIMLab/Gantry v2/Configuration_adv.h b/config/examples/ADIMLab/Gantry v2/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/Alfawise/U20-bltouch/Configuration_adv.h b/config/examples/Alfawise/U20-bltouch/Configuration_adv.h
@@ -1974,28 +1974,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -1964,28 +1964,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]

diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -1963,28 +1963,28 @@
     // Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
     // (e.g. 30), in steps of PTC_SAMPLE_RES (e.g. 5) with PTC_SAMPLE_COUNT (e.g. 10) samples.
 
-    //#define PTC_SAMPLE_START  30.0f
-    //#define PTC_SAMPLE_RES    5.0f
-    //#define PTC_SAMPLE_COUNT  10U
+    //#define PTC_SAMPLE_START  30  // (°C)
+    //#define PTC_SAMPLE_RES     5  // (°C)
+    //#define PTC_SAMPLE_COUNT  10
 
     // Bed temperature calibration builds a similar table.
 
-    //#define BTC_SAMPLE_START  60.0f
-    //#define BTC_SAMPLE_RES    5.0f
-    //#define BTC_SAMPLE_COUNT  10U
+    //#define BTC_SAMPLE_START  60  // (°C)
+    //#define BTC_SAMPLE_RES     5  // (°C)
+    //#define BTC_SAMPLE_COUNT  10
 
     // The temperature the probe should be at while taking measurements during bed temperature
     // calibration.
-    //#define BTC_PROBE_TEMP 30.0f
+    //#define BTC_PROBE_TEMP 30
 
     // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
     // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
     // increasing the height the probe is raised to.
-    //#define PTC_PROBE_RAISE 15U
+    //#define PTC_PROBE_RAISE 15
 
     // If the probe is outside of the defined range, use linear extrapolation using the closest
     // point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]