V4.19 r1.4 pangu #5

jyorin · 2020-05-28T08:10:11Z

download

The PanGu board use STM32MP157 SoC, and support more functions. Such as HDMI, ethernet, USB host, USB OTG, LCD, MIPI, Camera etc..

removed the unused flash section

Move camera(ov5640) into i2c5 section. Fix the clock pinmux of i2s2.

1. disable HDMI when LCD is using 2. fix the IRQ line of ft5316 chip conflict with same number, so switch the IRQ and reset line 3. The DCMI using 8bit data line

support LCDs size are 4.3inch and 7inch. support touch IC is GT9147.

The stm32mp1 can not configre a pin with pinctrl and gpio framework at same time. We need disable it to configure the irq pin of gt9147 use pull-down setting.

The host use QMI method to communicate with LTE module.

i2M-LCD043P800C i2M-LCD070P1024C

NAND variant stm32mp157a-i2cmp15xbn.dts eMMC variant stm32mp157a-i2cmp15xbe.dts

enable gpio watchdog enalbe load HDMI EDID firmware enable USB HID devices

usb serial driver usb rndis driver

Allow to share the codec port between two CPU DAIs. The stm32mp1 has two DAIs, sai2a and sai2b. But the codec has one port. Playback: CPU-A-DAI -> CODEC-DAI/port0 Capture: CPU-A-DAI <- CODEC-DAI/port0 However, the audio graph card parses the codec nods, it expects to find DAI interface indexes matching the endpoint indexes. STMicroelectronics@449dcf9

The i2M-GiantAxe board is a extension board for PanGu board. It's adds 4G LTE slot, WiFi & BT module, RS232, RS485, CAN, I2C, SPI and TIM1 signal.

The i2C-MP15X-B board has wm8904 and ksz9301 chip.

ST-dot-com · 2020-05-28T08:10:13Z

This pull request has been refused, the Contribution License Agreement must be signed.

[ Upstream commit a866759 ] This reverts commit 64e62bd. This commit ends up causing some lockdep splats due to trying to grab the payload lock while holding the mgr's lock: [ 54.010099] [ 54.011765] ====================================================== [ 54.018670] WARNING: possible circular locking dependency detected [ 54.025577] 5.5.0-rc6-02274-g77381c23ee63 torvalds#47 Not tainted [ 54.031610] ------------------------------------------------------ [ 54.038516] kworker/1:6/1040 is trying to acquire lock: [ 54.044354] ffff888272af3228 (&mgr->payload_lock){+.+.}, at: drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.054957] [ 54.054957] but task is already holding lock: [ 54.061473] ffff888272af3060 (&mgr->lock){+.+.}, at: drm_dp_mst_topology_mgr_set_mst+0x3c/0x2e4 [ 54.071193] [ 54.071193] which lock already depends on the new lock. [ 54.071193] [ 54.080334] [ 54.080334] the existing dependency chain (in reverse order) is: [ 54.088697] [ 54.088697] -> #1 (&mgr->lock){+.+.}: [ 54.094440] __mutex_lock+0xc3/0x498 [ 54.099015] drm_dp_mst_topology_get_port_validated+0x25/0x80 [ 54.106018] drm_dp_update_payload_part1+0xa2/0x2e2 [ 54.112051] intel_mst_pre_enable_dp+0x144/0x18f [ 54.117791] intel_encoders_pre_enable+0x63/0x70 [ 54.123532] hsw_crtc_enable+0xa1/0x722 [ 54.128396] intel_update_crtc+0x50/0x194 [ 54.133455] skl_commit_modeset_enables+0x40c/0x540 [ 54.139485] intel_atomic_commit_tail+0x5f7/0x130d [ 54.145418] intel_atomic_commit+0x2c8/0x2d8 [ 54.150770] drm_atomic_helper_set_config+0x5a/0x70 [ 54.156801] drm_mode_setcrtc+0x2ab/0x833 [ 54.161862] drm_ioctl+0x2e5/0x424 [ 54.166242] vfs_ioctl+0x21/0x2f [ 54.170426] do_vfs_ioctl+0x5fb/0x61e [ 54.175096] ksys_ioctl+0x55/0x75 [ 54.179377] __x64_sys_ioctl+0x1a/0x1e [ 54.184146] do_syscall_64+0x5c/0x6d [ 54.188721] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 54.194946] [ 54.194946] -> #0 (&mgr->payload_lock){+.+.}: [ 54.201463] [ 54.201463] other info that might help us debug this: [ 54.201463] [ 54.210410] Possible unsafe locking scenario: [ 54.210410] [ 54.217025] CPU0 CPU1 [ 54.222082] ---- ---- [ 54.227138] lock(&mgr->lock); [ 54.230643] lock(&mgr->payload_lock); [ 54.237742] lock(&mgr->lock); [ 54.244062] lock(&mgr->payload_lock); [ 54.248346] [ 54.248346] *** DEADLOCK *** [ 54.248346] [ 54.254959] 7 locks held by kworker/1:6/1040: [ 54.259822] #0: ffff888275c4f528 ((wq_completion)events){+.+.}, at: worker_thread+0x455/0x6e2 [ 54.269451] #1: ffffc9000119beb0 ((work_completion)(&(&dev_priv->hotplug.hotplug_work)->work)){+.+.}, at: worker_thread+0x455/0x6e2 [ 54.282768] #2: ffff888272a403f0 (&dev->mode_config.mutex){+.+.}, at: i915_hotplug_work_func+0x4b/0x2be [ 54.293368] #3: ffffffff824fc6c0 (drm_connector_list_iter){.+.+}, at: i915_hotplug_work_func+0x17e/0x2be [ 54.304061] #4: ffffc9000119bc58 (crtc_ww_class_acquire){+.+.}, at: drm_helper_probe_detect_ctx+0x40/0xfd [ 54.314855] #5: ffff888272a40470 (crtc_ww_class_mutex){+.+.}, at: drm_modeset_lock+0x74/0xe2 [ 54.324385] #6: ffff888272af3060 (&mgr->lock){+.+.}, at: drm_dp_mst_topology_mgr_set_mst+0x3c/0x2e4 [ 54.334597] [ 54.334597] stack backtrace: [ 54.339464] CPU: 1 PID: 1040 Comm: kworker/1:6 Not tainted 5.5.0-rc6-02274-g77381c23ee63 torvalds#47 [ 54.348893] Hardware name: Google Fizz/Fizz, BIOS Google_Fizz.10139.39.0 01/04/2018 [ 54.357451] Workqueue: events i915_hotplug_work_func [ 54.362995] Call Trace: [ 54.365724] dump_stack+0x71/0x9c [ 54.369427] check_noncircular+0x91/0xbc [ 54.373809] ? __lock_acquire+0xc9e/0xf66 [ 54.378286] ? __lock_acquire+0xc9e/0xf66 [ 54.382763] ? lock_acquire+0x175/0x1ac [ 54.387048] ? drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.393177] ? __mutex_lock+0xc3/0x498 [ 54.397362] ? drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.403492] ? drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.409620] ? drm_dp_dpcd_access+0xd9/0x101 [ 54.414390] ? drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.420517] ? drm_dp_mst_topology_mgr_set_mst+0x218/0x2e4 [ 54.426645] ? intel_digital_port_connected+0x34d/0x35c [ 54.432482] ? intel_dp_detect+0x227/0x44e [ 54.437056] ? ww_mutex_lock+0x49/0x9a [ 54.441242] ? drm_helper_probe_detect_ctx+0x75/0xfd [ 54.446789] ? intel_encoder_hotplug+0x4b/0x97 [ 54.451752] ? intel_ddi_hotplug+0x61/0x2e0 [ 54.456423] ? mark_held_locks+0x53/0x68 [ 54.460803] ? _raw_spin_unlock_irqrestore+0x3a/0x51 [ 54.466347] ? lockdep_hardirqs_on+0x187/0x1a4 [ 54.471310] ? drm_connector_list_iter_next+0x89/0x9a [ 54.476953] ? i915_hotplug_work_func+0x206/0x2be [ 54.482208] ? worker_thread+0x4d5/0x6e2 [ 54.486587] ? worker_thread+0x455/0x6e2 [ 54.490966] ? queue_work_on+0x64/0x64 [ 54.495151] ? kthread+0x1e9/0x1f1 [ 54.498946] ? queue_work_on+0x64/0x64 [ 54.503130] ? kthread_unpark+0x5e/0x5e [ 54.507413] ? ret_from_fork+0x3a/0x50 The proper fix for this is probably cleanup the VCPI allocations when we're enabling the topology, or on the first payload allocation. For now though, let's just revert. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 64e62bd ("drm/dp_mst: Remove VCPI while disabling topology mgr") Cc: Sean Paul <sean@poorly.run> Cc: Wayne Lin <Wayne.Lin@amd.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200117205149.97262-1-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 432cd2a upstream. When running relocation of a data block group while scrub is running in parallel, it is possible that the relocation will fail and abort the current transaction with an -EINVAL error: [134243.988595] BTRFS info (device sdc): found 14 extents, stage: move data extents [134243.999871] ------------[ cut here ]------------ [134244.000741] BTRFS: Transaction aborted (error -22) [134244.001692] WARNING: CPU: 0 PID: 26954 at fs/btrfs/ctree.c:1071 __btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.003380] Modules linked in: btrfs blake2b_generic xor raid6_pq (...) [134244.012577] CPU: 0 PID: 26954 Comm: btrfs Tainted: G W 5.6.0-rc7-btrfs-next-58 #5 [134244.014162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [134244.016184] RIP: 0010:__btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.017151] Code: 48 c7 c7 (...) [134244.020549] RSP: 0018:ffffa41607863888 EFLAGS: 00010286 [134244.021515] RAX: 0000000000000000 RBX: ffff9614bdfe09c8 RCX: 0000000000000000 [134244.022822] RDX: 0000000000000001 RSI: ffffffffb3d63980 RDI: 0000000000000001 [134244.024124] RBP: ffff961589e8c000 R08: 0000000000000000 R09: 0000000000000001 [134244.025424] R10: ffffffffc0ae5955 R11: 0000000000000000 R12: ffff9614bd530d08 [134244.026725] R13: ffff9614ced41b88 R14: ffff9614bdfe2a48 R15: 0000000000000000 [134244.028024] FS: 00007f29b63c08c0(0000) GS:ffff9615ba600000(0000) knlGS:0000000000000000 [134244.029491] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [134244.030560] CR2: 00007f4eb339b000 CR3: 0000000130d6e006 CR4: 00000000003606f0 [134244.031997] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [134244.033153] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [134244.034484] Call Trace: [134244.034984] btrfs_cow_block+0x12b/0x2b0 [btrfs] [134244.035859] do_relocation+0x30b/0x790 [btrfs] [134244.036681] ? do_raw_spin_unlock+0x49/0xc0 [134244.037460] ? _raw_spin_unlock+0x29/0x40 [134244.038235] relocate_tree_blocks+0x37b/0x730 [btrfs] [134244.039245] relocate_block_group+0x388/0x770 [btrfs] [134244.040228] btrfs_relocate_block_group+0x161/0x2e0 [btrfs] [134244.041323] btrfs_relocate_chunk+0x36/0x110 [btrfs] [134244.041345] btrfs_balance+0xc06/0x1860 [btrfs] [134244.043382] ? btrfs_ioctl_balance+0x27c/0x310 [btrfs] [134244.045586] btrfs_ioctl_balance+0x1ed/0x310 [btrfs] [134244.045611] btrfs_ioctl+0x1880/0x3760 [btrfs] [134244.049043] ? do_raw_spin_unlock+0x49/0xc0 [134244.049838] ? _raw_spin_unlock+0x29/0x40 [134244.050587] ? __handle_mm_fault+0x11b3/0x14b0 [134244.051417] ? ksys_ioctl+0x92/0xb0 [134244.052070] ksys_ioctl+0x92/0xb0 [134244.052701] ? trace_hardirqs_off_thunk+0x1a/0x1c [134244.053511] __x64_sys_ioctl+0x16/0x20 [134244.054206] do_syscall_64+0x5c/0x280 [134244.054891] entry_SYSCALL_64_after_hwframe+0x49/0xbe [134244.055819] RIP: 0033:0x7f29b51c9dd7 [134244.056491] Code: 00 00 00 (...) [134244.059767] RSP: 002b:00007ffcccc1dd08 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 [134244.061168] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f29b51c9dd7 [134244.062474] RDX: 00007ffcccc1dda0 RSI: 00000000c4009420 RDI: 0000000000000003 [134244.063771] RBP: 0000000000000003 R08: 00005565cea4b000 R09: 0000000000000000 [134244.065032] R10: 0000000000000541 R11: 0000000000000202 R12: 00007ffcccc2060a [134244.066327] R13: 00007ffcccc1dda0 R14: 0000000000000002 R15: 00007ffcccc1dec0 [134244.067626] irq event stamp: 0 [134244.068202] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [134244.069351] hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.070909] softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.072392] softirqs last disabled at (0): [<0000000000000000>] 0x0 [134244.073432] ---[ end trace bd7c03622e0b0a99 ]--- The -EINVAL error comes from the following chain of function calls: __btrfs_cow_block() <-- aborts the transaction btrfs_reloc_cow_block() replace_file_extents() get_new_location() <-- returns -EINVAL When relocating a data block group, for each allocated extent of the block group, we preallocate another extent (at prealloc_file_extent_cluster()), associated with the data relocation inode, and then dirty all its pages. These preallocated extents have, and must have, the same size that extents from the data block group being relocated have. Later before we start the relocation stage that updates pointers (bytenr field of file extent items) to point to the the new extents, we trigger writeback for the data relocation inode. The expectation is that writeback will write the pages to the previously preallocated extents, that it follows the NOCOW path. That is generally the case, however, if a scrub is running it may have turned the block group that contains those extents into RO mode, in which case writeback falls back to the COW path. However in the COW path instead of allocating exactly one extent with the expected size, the allocator may end up allocating several smaller extents due to free space fragmentation - because we tell it at cow_file_range() that the minimum allocation size can match the filesystem's sector size. This later breaks the relocation's expectation that an extent associated to a file extent item in the data relocation inode has the same size as the respective extent pointed by a file extent item in another tree - in this case the extent to which the relocation inode poins to is smaller, causing relocation.c:get_new_location() to return -EINVAL. For example, if we are relocating a data block group X that has a logical address of X and the block group has an extent allocated at the logical address X + 128KiB with a size of 64KiB: 1) At prealloc_file_extent_cluster() we allocate an extent for the data relocation inode with a size of 64KiB and associate it to the file offset 128KiB (X + 128KiB - X) of the data relocation inode. This preallocated extent was allocated at block group Z; 2) A scrub running in parallel turns block group Z into RO mode and starts scrubing its extents; 3) Relocation triggers writeback for the data relocation inode; 4) When running delalloc (btrfs_run_delalloc_range()), we try first the NOCOW path because the data relocation inode has BTRFS_INODE_PREALLOC set in its flags. However, because block group Z is in RO mode, the NOCOW path (run_delalloc_nocow()) falls back into the COW path, by calling cow_file_range(); 5) At cow_file_range(), in the first iteration of the while loop we call btrfs_reserve_extent() to allocate a 64KiB extent and pass it a minimum allocation size of 4KiB (fs_info->sectorsize). Due to free space fragmentation, btrfs_reserve_extent() ends up allocating two extents of 32KiB each, each one on a different iteration of that while loop; 6) Writeback of the data relocation inode completes; 7) Relocation proceeds and ends up at relocation.c:replace_file_extents(), with a leaf which has a file extent item that points to the data extent from block group X, that has a logical address (bytenr) of X + 128KiB and a size of 64KiB. Then it calls get_new_location(), which does a lookup in the data relocation tree for a file extent item starting at offset 128KiB (X + 128KiB - X) and belonging to the data relocation inode. It finds a corresponding file extent item, however that item points to an extent that has a size of 32KiB, which doesn't match the expected size of 64KiB, resuling in -EINVAL being returned from this function and propagated up to __btrfs_cow_block(), which aborts the current transaction. To fix this make sure that at cow_file_range() when we call the allocator we pass it a minimum allocation size corresponding the desired extent size if the inode belongs to the data relocation tree, otherwise pass it the filesystem's sector size as the minimum allocation size. CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e24c644 ] I compiled with AddressSanitizer and I had these memory leaks while I was using the tep_parse_format function: Direct leak of 28 byte(s) in 4 object(s) allocated from: #0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe) #1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985 #2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140 #3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206 #4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291 #5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299 #6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849 #7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161 #8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207 #9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786 #10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285 #11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369 #12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335 #13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389 #14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431 #15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251 #16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284 #17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593 #18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727 #19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048 #20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127 #21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152 #22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252 #23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347 #24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461 #25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673 #26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2) The token variable in the process_dynamic_array_len function is allocated in the read_expect_type function, but is not freed before calling the read_token function. Free the token variable before calling read_token in order to plug the leak. Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Link: https://lore.kernel.org/linux-trace-devel/20200730150236.5392-1-pduplessis@efficios.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 18c850f upstream. There's long existed a lockdep splat because we open our bdev's under the ->device_list_mutex at mount time, which acquires the bd_mutex. Usually this goes unnoticed, but if you do loopback devices at all suddenly the bd_mutex comes with a whole host of other dependencies, which results in the splat when you mount a btrfs file system. ====================================================== WARNING: possible circular locking dependency detected 5.8.0-0.rc3.1.fc33.x86_64+debug #1 Not tainted ------------------------------------------------------ systemd-journal/509 is trying to acquire lock: ffff970831f84db0 (&fs_info->reloc_mutex){+.+.}-{3:3}, at: btrfs_record_root_in_trans+0x44/0x70 [btrfs] but task is already holding lock: ffff97083144d598 (sb_pagefaults){.+.+}-{0:0}, at: btrfs_page_mkwrite+0x59/0x560 [btrfs] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #6 (sb_pagefaults){.+.+}-{0:0}: __sb_start_write+0x13e/0x220 btrfs_page_mkwrite+0x59/0x560 [btrfs] do_page_mkwrite+0x4f/0x130 do_wp_page+0x3b0/0x4f0 handle_mm_fault+0xf47/0x1850 do_user_addr_fault+0x1fc/0x4b0 exc_page_fault+0x88/0x300 asm_exc_page_fault+0x1e/0x30 -> #5 (&mm->mmap_lock#2){++++}-{3:3}: __might_fault+0x60/0x80 _copy_from_user+0x20/0xb0 get_sg_io_hdr+0x9a/0xb0 scsi_cmd_ioctl+0x1ea/0x2f0 cdrom_ioctl+0x3c/0x12b4 sr_block_ioctl+0xa4/0xd0 block_ioctl+0x3f/0x50 ksys_ioctl+0x82/0xc0 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x52/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #4 (&cd->lock){+.+.}-{3:3}: __mutex_lock+0x7b/0x820 sr_block_open+0xa2/0x180 __blkdev_get+0xdd/0x550 blkdev_get+0x38/0x150 do_dentry_open+0x16b/0x3e0 path_openat+0x3c9/0xa00 do_filp_open+0x75/0x100 do_sys_openat2+0x8a/0x140 __x64_sys_openat+0x46/0x70 do_syscall_64+0x52/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #3 (&bdev->bd_mutex){+.+.}-{3:3}: __mutex_lock+0x7b/0x820 __blkdev_get+0x6a/0x550 blkdev_get+0x85/0x150 blkdev_get_by_path+0x2c/0x70 btrfs_get_bdev_and_sb+0x1b/0xb0 [btrfs] open_fs_devices+0x88/0x240 [btrfs] btrfs_open_devices+0x92/0xa0 [btrfs] btrfs_mount_root+0x250/0x490 [btrfs] legacy_get_tree+0x30/0x50 vfs_get_tree+0x28/0xc0 vfs_kern_mount.part.0+0x71/0xb0 btrfs_mount+0x119/0x380 [btrfs] legacy_get_tree+0x30/0x50 vfs_get_tree+0x28/0xc0 do_mount+0x8c6/0xca0 __x64_sys_mount+0x8e/0xd0 do_syscall_64+0x52/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #2 (&fs_devs->device_list_mutex){+.+.}-{3:3}: __mutex_lock+0x7b/0x820 btrfs_run_dev_stats+0x36/0x420 [btrfs] commit_cowonly_roots+0x91/0x2d0 [btrfs] btrfs_commit_transaction+0x4e6/0x9f0 [btrfs] btrfs_sync_file+0x38a/0x480 [btrfs] __x64_sys_fdatasync+0x47/0x80 do_syscall_64+0x52/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #1 (&fs_info->tree_log_mutex){+.+.}-{3:3}: __mutex_lock+0x7b/0x820 btrfs_commit_transaction+0x48e/0x9f0 [btrfs] btrfs_sync_file+0x38a/0x480 [btrfs] __x64_sys_fdatasync+0x47/0x80 do_syscall_64+0x52/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xa9 -> #0 (&fs_info->reloc_mutex){+.+.}-{3:3}: __lock_acquire+0x1241/0x20c0 lock_acquire+0xb0/0x400 __mutex_lock+0x7b/0x820 btrfs_record_root_in_trans+0x44/0x70 [btrfs] start_transaction+0xd2/0x500 [btrfs] btrfs_dirty_inode+0x44/0xd0 [btrfs] file_update_time+0xc6/0x120 btrfs_page_mkwrite+0xda/0x560 [btrfs] do_page_mkwrite+0x4f/0x130 do_wp_page+0x3b0/0x4f0 handle_mm_fault+0xf47/0x1850 do_user_addr_fault+0x1fc/0x4b0 exc_page_fault+0x88/0x300 asm_exc_page_fault+0x1e/0x30 other info that might help us debug this: Chain exists of: &fs_info->reloc_mutex --> &mm->mmap_lock#2 --> sb_pagefaults Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(sb_pagefaults); lock(&mm->mmap_lock#2); lock(sb_pagefaults); lock(&fs_info->reloc_mutex); *** DEADLOCK *** 3 locks held by systemd-journal/509: #0: ffff97083bdec8b8 (&mm->mmap_lock#2){++++}-{3:3}, at: do_user_addr_fault+0x12e/0x4b0 #1: ffff97083144d598 (sb_pagefaults){.+.+}-{0:0}, at: btrfs_page_mkwrite+0x59/0x560 [btrfs] #2: ffff97083144d6a8 (sb_internal){.+.+}-{0:0}, at: start_transaction+0x3f8/0x500 [btrfs] stack backtrace: CPU: 0 PID: 509 Comm: systemd-journal Not tainted 5.8.0-0.rc3.1.fc33.x86_64+debug #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 Call Trace: dump_stack+0x92/0xc8 check_noncircular+0x134/0x150 __lock_acquire+0x1241/0x20c0 lock_acquire+0xb0/0x400 ? btrfs_record_root_in_trans+0x44/0x70 [btrfs] ? lock_acquire+0xb0/0x400 ? btrfs_record_root_in_trans+0x44/0x70 [btrfs] __mutex_lock+0x7b/0x820 ? btrfs_record_root_in_trans+0x44/0x70 [btrfs] ? kvm_sched_clock_read+0x14/0x30 ? sched_clock+0x5/0x10 ? sched_clock_cpu+0xc/0xb0 btrfs_record_root_in_trans+0x44/0x70 [btrfs] start_transaction+0xd2/0x500 [btrfs] btrfs_dirty_inode+0x44/0xd0 [btrfs] file_update_time+0xc6/0x120 btrfs_page_mkwrite+0xda/0x560 [btrfs] ? sched_clock+0x5/0x10 do_page_mkwrite+0x4f/0x130 do_wp_page+0x3b0/0x4f0 handle_mm_fault+0xf47/0x1850 do_user_addr_fault+0x1fc/0x4b0 exc_page_fault+0x88/0x300 ? asm_exc_page_fault+0x8/0x30 asm_exc_page_fault+0x1e/0x30 RIP: 0033:0x7fa3972fdbfe Code: Bad RIP value. Fix this by not holding the ->device_list_mutex at this point. The device_list_mutex exists to protect us from modifying the device list while the file system is running. However it can also be modified by doing a scan on a device. But this action is specifically protected by the uuid_mutex, which we are holding here. We cannot race with opening at this point because we have the ->s_mount lock held during the mount. Not having the ->device_list_mutex here is perfectly safe as we're not going to change the devices at this point. CC: stable@vger.kernel.org # 4.19+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> [ add some comments ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…parallel commit 6bd335b upstream. When balance and scrub are running in parallel it is possible to end up with an underflow of the bytes_may_use counter of the data space_info object, which triggers a warning like the following: [134243.793196] BTRFS info (device sdc): relocating block group 1104150528 flags data [134243.806891] ------------[ cut here ]------------ [134243.807561] WARNING: CPU: 1 PID: 26884 at fs/btrfs/space-info.h:125 btrfs_add_reserved_bytes+0x1da/0x280 [btrfs] [134243.808819] Modules linked in: btrfs blake2b_generic xor (...) [134243.815779] CPU: 1 PID: 26884 Comm: kworker/u8:8 Tainted: G W 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 [134243.816944] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [134243.818389] Workqueue: writeback wb_workfn (flush-btrfs-108483) [134243.819186] RIP: 0010:btrfs_add_reserved_bytes+0x1da/0x280 [btrfs] [134243.819963] Code: 0b f2 85 (...) [134243.822271] RSP: 0018:ffffa4160aae7510 EFLAGS: 00010287 [134243.822929] RAX: 000000000000c000 RBX: ffff96159a8c1000 RCX: 0000000000000000 [134243.823816] RDX: 0000000000008000 RSI: 0000000000000000 RDI: ffff96158067a810 [134243.824742] RBP: ffff96158067a800 R08: 0000000000000001 R09: 0000000000000000 [134243.825636] R10: ffff961501432a40 R11: 0000000000000000 R12: 000000000000c000 [134243.826532] R13: 0000000000000001 R14: ffffffffffff4000 R15: ffff96158067a810 [134243.827432] FS: 0000000000000000(0000) GS:ffff9615baa00000(0000) knlGS:0000000000000000 [134243.828451] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [134243.829184] CR2: 000055bd7e414000 CR3: 00000001077be004 CR4: 00000000003606e0 [134243.830083] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [134243.830975] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [134243.831867] Call Trace: [134243.832211] find_free_extent+0x4a0/0x16c0 [btrfs] [134243.832846] btrfs_reserve_extent+0x91/0x180 [btrfs] [134243.833487] cow_file_range+0x12d/0x490 [btrfs] [134243.834080] fallback_to_cow+0x82/0x1b0 [btrfs] [134243.834689] ? release_extent_buffer+0x121/0x170 [btrfs] [134243.835370] run_delalloc_nocow+0x33f/0xa30 [btrfs] [134243.836032] btrfs_run_delalloc_range+0x1ea/0x6d0 [btrfs] [134243.836725] ? find_lock_delalloc_range+0x221/0x250 [btrfs] [134243.837450] writepage_delalloc+0xe8/0x150 [btrfs] [134243.838059] __extent_writepage+0xe8/0x4c0 [btrfs] [134243.838674] extent_write_cache_pages+0x237/0x530 [btrfs] [134243.839364] extent_writepages+0x44/0xa0 [btrfs] [134243.839946] do_writepages+0x23/0x80 [134243.840401] __writeback_single_inode+0x59/0x700 [134243.841006] writeback_sb_inodes+0x267/0x5f0 [134243.841548] __writeback_inodes_wb+0x87/0xe0 [134243.842091] wb_writeback+0x382/0x590 [134243.842574] ? wb_workfn+0x4a2/0x6c0 [134243.843030] wb_workfn+0x4a2/0x6c0 [134243.843468] process_one_work+0x26d/0x6a0 [134243.843978] worker_thread+0x4f/0x3e0 [134243.844452] ? process_one_work+0x6a0/0x6a0 [134243.844981] kthread+0x103/0x140 [134243.845400] ? kthread_create_worker_on_cpu+0x70/0x70 [134243.846030] ret_from_fork+0x3a/0x50 [134243.846494] irq event stamp: 0 [134243.846892] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [134243.847682] hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134243.848687] softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134243.849913] softirqs last disabled at (0): [<0000000000000000>] 0x0 [134243.850698] ---[ end trace bd7c03622e0b0a96 ]--- [134243.851335] ------------[ cut here ]------------ When relocating a data block group, for each extent allocated in the block group we preallocate another extent with the same size for the data relocation inode (we do it at prealloc_file_extent_cluster()). We reserve space by calling btrfs_check_data_free_space(), which ends up incrementing the data space_info's bytes_may_use counter, and then call btrfs_prealloc_file_range() to allocate the extent, which always decrements the bytes_may_use counter by the same amount. The expectation is that writeback of the data relocation inode always follows a NOCOW path, by writing into the preallocated extents. However, when starting writeback we might end up falling back into the COW path, because the block group that contains the preallocated extent was turned into RO mode by a scrub running in parallel. The COW path then calls the extent allocator which ends up calling btrfs_add_reserved_bytes(), and this function decrements the bytes_may_use counter of the data space_info object by an amount corresponding to the size of the allocated extent, despite we haven't previously incremented it. When the counter currently has a value smaller then the allocated extent we reset the counter to 0 and emit a warning, otherwise we just decrement it and slowly mess up with this counter which is crucial for space reservation, the end result can be granting reserved space to tasks when there isn't really enough free space, and having the tasks fail later in critical places where error handling consists of a transaction abort or hitting a BUG_ON(). Fix this by making sure that if we fallback to the COW path for a data relocation inode, we increment the bytes_may_use counter of the data space_info object. The COW path will then decrement it at btrfs_add_reserved_bytes() on success or through its error handling part by a call to extent_clear_unlock_delalloc() (which ends up calling btrfs_clear_delalloc_extent() that does the decrement operation) in case of an error. Test case btrfs/061 from fstests could sporadically trigger this. CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 432cd2a upstream. When running relocation of a data block group while scrub is running in parallel, it is possible that the relocation will fail and abort the current transaction with an -EINVAL error: [134243.988595] BTRFS info (device sdc): found 14 extents, stage: move data extents [134243.999871] ------------[ cut here ]------------ [134244.000741] BTRFS: Transaction aborted (error -22) [134244.001692] WARNING: CPU: 0 PID: 26954 at fs/btrfs/ctree.c:1071 __btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.003380] Modules linked in: btrfs blake2b_generic xor raid6_pq (...) [134244.012577] CPU: 0 PID: 26954 Comm: btrfs Tainted: G W 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 [134244.014162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [134244.016184] RIP: 0010:__btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.017151] Code: 48 c7 c7 (...) [134244.020549] RSP: 0018:ffffa41607863888 EFLAGS: 00010286 [134244.021515] RAX: 0000000000000000 RBX: ffff9614bdfe09c8 RCX: 0000000000000000 [134244.022822] RDX: 0000000000000001 RSI: ffffffffb3d63980 RDI: 0000000000000001 [134244.024124] RBP: ffff961589e8c000 R08: 0000000000000000 R09: 0000000000000001 [134244.025424] R10: ffffffffc0ae5955 R11: 0000000000000000 R12: ffff9614bd530d08 [134244.026725] R13: ffff9614ced41b88 R14: ffff9614bdfe2a48 R15: 0000000000000000 [134244.028024] FS: 00007f29b63c08c0(0000) GS:ffff9615ba600000(0000) knlGS:0000000000000000 [134244.029491] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [134244.030560] CR2: 00007f4eb339b000 CR3: 0000000130d6e006 CR4: 00000000003606f0 [134244.031997] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [134244.033153] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [134244.034484] Call Trace: [134244.034984] btrfs_cow_block+0x12b/0x2b0 [btrfs] [134244.035859] do_relocation+0x30b/0x790 [btrfs] [134244.036681] ? do_raw_spin_unlock+0x49/0xc0 [134244.037460] ? _raw_spin_unlock+0x29/0x40 [134244.038235] relocate_tree_blocks+0x37b/0x730 [btrfs] [134244.039245] relocate_block_group+0x388/0x770 [btrfs] [134244.040228] btrfs_relocate_block_group+0x161/0x2e0 [btrfs] [134244.041323] btrfs_relocate_chunk+0x36/0x110 [btrfs] [134244.041345] btrfs_balance+0xc06/0x1860 [btrfs] [134244.043382] ? btrfs_ioctl_balance+0x27c/0x310 [btrfs] [134244.045586] btrfs_ioctl_balance+0x1ed/0x310 [btrfs] [134244.045611] btrfs_ioctl+0x1880/0x3760 [btrfs] [134244.049043] ? do_raw_spin_unlock+0x49/0xc0 [134244.049838] ? _raw_spin_unlock+0x29/0x40 [134244.050587] ? __handle_mm_fault+0x11b3/0x14b0 [134244.051417] ? ksys_ioctl+0x92/0xb0 [134244.052070] ksys_ioctl+0x92/0xb0 [134244.052701] ? trace_hardirqs_off_thunk+0x1a/0x1c [134244.053511] __x64_sys_ioctl+0x16/0x20 [134244.054206] do_syscall_64+0x5c/0x280 [134244.054891] entry_SYSCALL_64_after_hwframe+0x49/0xbe [134244.055819] RIP: 0033:0x7f29b51c9dd7 [134244.056491] Code: 00 00 00 (...) [134244.059767] RSP: 002b:00007ffcccc1dd08 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 [134244.061168] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f29b51c9dd7 [134244.062474] RDX: 00007ffcccc1dda0 RSI: 00000000c4009420 RDI: 0000000000000003 [134244.063771] RBP: 0000000000000003 R08: 00005565cea4b000 R09: 0000000000000000 [134244.065032] R10: 0000000000000541 R11: 0000000000000202 R12: 00007ffcccc2060a [134244.066327] R13: 00007ffcccc1dda0 R14: 0000000000000002 R15: 00007ffcccc1dec0 [134244.067626] irq event stamp: 0 [134244.068202] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [134244.069351] hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.070909] softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.072392] softirqs last disabled at (0): [<0000000000000000>] 0x0 [134244.073432] ---[ end trace bd7c03622e0b0a99 ]--- The -EINVAL error comes from the following chain of function calls: __btrfs_cow_block() <-- aborts the transaction btrfs_reloc_cow_block() replace_file_extents() get_new_location() <-- returns -EINVAL When relocating a data block group, for each allocated extent of the block group, we preallocate another extent (at prealloc_file_extent_cluster()), associated with the data relocation inode, and then dirty all its pages. These preallocated extents have, and must have, the same size that extents from the data block group being relocated have. Later before we start the relocation stage that updates pointers (bytenr field of file extent items) to point to the the new extents, we trigger writeback for the data relocation inode. The expectation is that writeback will write the pages to the previously preallocated extents, that it follows the NOCOW path. That is generally the case, however, if a scrub is running it may have turned the block group that contains those extents into RO mode, in which case writeback falls back to the COW path. However in the COW path instead of allocating exactly one extent with the expected size, the allocator may end up allocating several smaller extents due to free space fragmentation - because we tell it at cow_file_range() that the minimum allocation size can match the filesystem's sector size. This later breaks the relocation's expectation that an extent associated to a file extent item in the data relocation inode has the same size as the respective extent pointed by a file extent item in another tree - in this case the extent to which the relocation inode poins to is smaller, causing relocation.c:get_new_location() to return -EINVAL. For example, if we are relocating a data block group X that has a logical address of X and the block group has an extent allocated at the logical address X + 128KiB with a size of 64KiB: 1) At prealloc_file_extent_cluster() we allocate an extent for the data relocation inode with a size of 64KiB and associate it to the file offset 128KiB (X + 128KiB - X) of the data relocation inode. This preallocated extent was allocated at block group Z; 2) A scrub running in parallel turns block group Z into RO mode and starts scrubing its extents; 3) Relocation triggers writeback for the data relocation inode; 4) When running delalloc (btrfs_run_delalloc_range()), we try first the NOCOW path because the data relocation inode has BTRFS_INODE_PREALLOC set in its flags. However, because block group Z is in RO mode, the NOCOW path (run_delalloc_nocow()) falls back into the COW path, by calling cow_file_range(); 5) At cow_file_range(), in the first iteration of the while loop we call btrfs_reserve_extent() to allocate a 64KiB extent and pass it a minimum allocation size of 4KiB (fs_info->sectorsize). Due to free space fragmentation, btrfs_reserve_extent() ends up allocating two extents of 32KiB each, each one on a different iteration of that while loop; 6) Writeback of the data relocation inode completes; 7) Relocation proceeds and ends up at relocation.c:replace_file_extents(), with a leaf which has a file extent item that points to the data extent from block group X, that has a logical address (bytenr) of X + 128KiB and a size of 64KiB. Then it calls get_new_location(), which does a lookup in the data relocation tree for a file extent item starting at offset 128KiB (X + 128KiB - X) and belonging to the data relocation inode. It finds a corresponding file extent item, however that item points to an extent that has a size of 32KiB, which doesn't match the expected size of 64KiB, resuling in -EINVAL being returned from this function and propagated up to __btrfs_cow_block(), which aborts the current transaction. To fix this make sure that at cow_file_range() when we call the allocator we pass it a minimum allocation size corresponding the desired extent size if the inode belongs to the data relocation tree, otherwise pass it the filesystem's sector size as the minimum allocation size. CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The below warning is splatting during guest reboot. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1931 at arch/x86/kvm/x86.c:10322 kvm_arch_vcpu_ioctl_run+0x874/0x880 [kvm] CPU: 0 PID: 1931 Comm: qemu-system-x86 Tainted: G I 5.17.0-rc1+ STMicroelectronics#5 RIP: 0010:kvm_arch_vcpu_ioctl_run+0x874/0x880 [kvm] Call Trace: <TASK> kvm_vcpu_ioctl+0x279/0x710 [kvm] __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fd39797350b This can be triggered by not exposing tsc-deadline mode and doing a reboot in the guest. The lapic_shutdown() function which is called in sys_reboot path will not disarm the flying timer, it just masks LVTT. lapic_shutdown() clears APIC state w/ LVT_MASKED and timer-mode bit is 0, this can trigger timer-mode switch between tsc-deadline and oneshot/periodic, which can result in preemption timer be cancelled in apic_update_lvtt(). However, We can't depend on this when not exposing tsc-deadline mode and oneshot/periodic modes emulated by preemption timer. Qemu will synchronise states around reset, let's cancel preemption timer under KVM_SET_LAPIC. Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Message-Id: <1643102220-35667-1-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

[ Upstream commit 8410f70 ] Our test report a UAF: [ 2073.019181] ================================================================== [ 2073.019188] BUG: KASAN: use-after-free in __bfq_put_async_bfqq+0xa0/0x168 [ 2073.019191] Write of size 8 at addr ffff8000ccf64128 by task rmmod/72584 [ 2073.019192] [ 2073.019196] CPU: 0 PID: 72584 Comm: rmmod Kdump: loaded Not tainted 4.19.90-yk #5 [ 2073.019198] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 2073.019200] Call trace: [ 2073.019203] dump_backtrace+0x0/0x310 [ 2073.019206] show_stack+0x28/0x38 [ 2073.019210] dump_stack+0xec/0x15c [ 2073.019216] print_address_description+0x68/0x2d0 [ 2073.019220] kasan_report+0x238/0x2f0 [ 2073.019224] __asan_store8+0x88/0xb0 [ 2073.019229] __bfq_put_async_bfqq+0xa0/0x168 [ 2073.019233] bfq_put_async_queues+0xbc/0x208 [ 2073.019236] bfq_pd_offline+0x178/0x238 [ 2073.019240] blkcg_deactivate_policy+0x1f0/0x420 [ 2073.019244] bfq_exit_queue+0x128/0x178 [ 2073.019249] blk_mq_exit_sched+0x12c/0x160 [ 2073.019252] elevator_exit+0xc8/0xd0 [ 2073.019256] blk_exit_queue+0x50/0x88 [ 2073.019259] blk_cleanup_queue+0x228/0x3d8 [ 2073.019267] null_del_dev+0xfc/0x1e0 [null_blk] [ 2073.019274] null_exit+0x90/0x114 [null_blk] [ 2073.019278] __arm64_sys_delete_module+0x358/0x5a0 [ 2073.019282] el0_svc_common+0xc8/0x320 [ 2073.019287] el0_svc_handler+0xf8/0x160 [ 2073.019290] el0_svc+0x10/0x218 [ 2073.019291] [ 2073.019294] Allocated by task 14163: [ 2073.019301] kasan_kmalloc+0xe0/0x190 [ 2073.019305] kmem_cache_alloc_node_trace+0x1cc/0x418 [ 2073.019308] bfq_pd_alloc+0x54/0x118 [ 2073.019313] blkcg_activate_policy+0x250/0x460 [ 2073.019317] bfq_create_group_hierarchy+0x38/0x110 [ 2073.019321] bfq_init_queue+0x6d0/0x948 [ 2073.019325] blk_mq_init_sched+0x1d8/0x390 [ 2073.019330] elevator_switch_mq+0x88/0x170 [ 2073.019334] elevator_switch+0x140/0x270 [ 2073.019338] elv_iosched_store+0x1a4/0x2a0 [ 2073.019342] queue_attr_store+0x90/0xe0 [ 2073.019348] sysfs_kf_write+0xa8/0xe8 [ 2073.019351] kernfs_fop_write+0x1f8/0x378 [ 2073.019359] __vfs_write+0xe0/0x360 [ 2073.019363] vfs_write+0xf0/0x270 [ 2073.019367] ksys_write+0xdc/0x1b8 [ 2073.019371] __arm64_sys_write+0x50/0x60 [ 2073.019375] el0_svc_common+0xc8/0x320 [ 2073.019380] el0_svc_handler+0xf8/0x160 [ 2073.019383] el0_svc+0x10/0x218 [ 2073.019385] [ 2073.019387] Freed by task 72584: [ 2073.019391] __kasan_slab_free+0x120/0x228 [ 2073.019394] kasan_slab_free+0x10/0x18 [ 2073.019397] kfree+0x94/0x368 [ 2073.019400] bfqg_put+0x64/0xb0 [ 2073.019404] bfqg_and_blkg_put+0x90/0xb0 [ 2073.019408] bfq_put_queue+0x220/0x228 [ 2073.019413] __bfq_put_async_bfqq+0x98/0x168 [ 2073.019416] bfq_put_async_queues+0xbc/0x208 [ 2073.019420] bfq_pd_offline+0x178/0x238 [ 2073.019424] blkcg_deactivate_policy+0x1f0/0x420 [ 2073.019429] bfq_exit_queue+0x128/0x178 [ 2073.019433] blk_mq_exit_sched+0x12c/0x160 [ 2073.019437] elevator_exit+0xc8/0xd0 [ 2073.019440] blk_exit_queue+0x50/0x88 [ 2073.019443] blk_cleanup_queue+0x228/0x3d8 [ 2073.019451] null_del_dev+0xfc/0x1e0 [null_blk] [ 2073.019459] null_exit+0x90/0x114 [null_blk] [ 2073.019462] __arm64_sys_delete_module+0x358/0x5a0 [ 2073.019467] el0_svc_common+0xc8/0x320 [ 2073.019471] el0_svc_handler+0xf8/0x160 [ 2073.019474] el0_svc+0x10/0x218 [ 2073.019475] [ 2073.019479] The buggy address belongs to the object at ffff8000ccf63f00 which belongs to the cache kmalloc-1024 of size 1024 [ 2073.019484] The buggy address is located 552 bytes inside of 1024-byte region [ffff8000ccf63f00, ffff8000ccf64300) [ 2073.019486] The buggy address belongs to the page: [ 2073.019492] page:ffff7e000333d800 count:1 mapcount:0 mapping:ffff8000c0003a00 index:0x0 compound_mapcount: 0 [ 2073.020123] flags: 0x7ffff0000008100(slab|head) [ 2073.020403] raw: 07ffff0000008100 ffff7e0003334c08 ffff7e00001f5a08 ffff8000c0003a00 [ 2073.020409] raw: 0000000000000000 00000000001c001c 00000001ffffffff 0000000000000000 [ 2073.020411] page dumped because: kasan: bad access detected [ 2073.020412] [ 2073.020414] Memory state around the buggy address: [ 2073.020420] ffff8000ccf64000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 2073.020424] ffff8000ccf64080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 2073.020428] >ffff8000ccf64100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 2073.020430] ^ [ 2073.020434] ffff8000ccf64180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 2073.020438] ffff8000ccf64200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 2073.020439] ================================================================== The same problem exist in mainline as well. This is because oom_bfqq is moved to a non-root group, thus root_group is freed earlier. Thus fix the problem by don't move oom_bfqq. Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Paolo Valente <paolo.valente@linaro.org> Link: https://lore.kernel.org/r/20220129015924.3958918-4-yukuai3@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 447c799 ] Noticed the below warning while running a pytorch workload on vega10 GPUs. Change to trylock to avoid conflicts with already held reservation locks. [ +0.000003] WARNING: possible recursive locking detected [ +0.000003] 5.13.0-kfd-rajneesh torvalds#1030 Not tainted [ +0.000004] -------------------------------------------- [ +0.000002] python/4822 is trying to acquire lock: [ +0.000004] ffff932cd9a259f8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000203] but task is already holding lock: [ +0.000003] ffff932cbb7181f8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: ttm_eu_reserve_buffers+0x270/0x470 [ttm] [ +0.000017] other info that might help us debug this: [ +0.000002] Possible unsafe locking scenario: [ +0.000003] CPU0 [ +0.000002] ---- [ +0.000002] lock(reservation_ww_class_mutex); [ +0.000004] lock(reservation_ww_class_mutex); [ +0.000003] *** DEADLOCK *** [ +0.000002] May be due to missing lock nesting notation [ +0.000003] 7 locks held by python/4822: [ +0.000003] #0: ffff932c4ac028d0 (&process->mutex){+.+.}-{3:3}, at: kfd_ioctl_map_memory_to_gpu+0x10b/0x320 [amdgpu] [ +0.000232] #1: ffff932c55e830a8 (&info->lock#2){+.+.}-{3:3}, at: amdgpu_amdkfd_gpuvm_map_memory_to_gpu+0x64/0xf60 [amdgpu] [ +0.000241] #2: ffff932cc45b5e68 (&(*mem)->lock){+.+.}-{3:3}, at: amdgpu_amdkfd_gpuvm_map_memory_to_gpu+0xdf/0xf60 [amdgpu] [ +0.000236] #3: ffffb2b35606fd28 (reservation_ww_class_acquire){+.+.}-{0:0}, at: amdgpu_amdkfd_gpuvm_map_memory_to_gpu+0x232/0xf60 [amdgpu] [ +0.000235] #4: ffff932cbb7181f8 (reservation_ww_class_mutex){+.+.}-{3:3}, at: ttm_eu_reserve_buffers+0x270/0x470 [ttm] [ +0.000015] #5: ffffffffc045f700 (*(sspp++)){....}-{0:0}, at: drm_dev_enter+0x5/0xa0 [drm] [ +0.000038] #6: ffff932c52da7078 (&vm->eviction_lock){+.+.}-{3:3}, at: amdgpu_vm_bo_update_mapping+0xd5/0x4f0 [amdgpu] [ +0.000195] stack backtrace: [ +0.000003] CPU: 11 PID: 4822 Comm: python Not tainted 5.13.0-kfd-rajneesh torvalds#1030 [ +0.000005] Hardware name: GIGABYTE MZ01-CE0-00/MZ01-CE0-00, BIOS F02 08/29/2018 [ +0.000003] Call Trace: [ +0.000003] dump_stack+0x6d/0x89 [ +0.000010] __lock_acquire+0xb93/0x1a90 [ +0.000009] lock_acquire+0x25d/0x2d0 [ +0.000005] ? amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000184] ? lock_is_held_type+0xa2/0x110 [ +0.000006] ? amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000184] __ww_mutex_lock.constprop.17+0xca/0x1060 [ +0.000007] ? amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000183] ? lock_release+0x13f/0x270 [ +0.000005] ? lock_is_held_type+0xa2/0x110 [ +0.000006] ? amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000183] amdgpu_bo_release_notify+0xc4/0x160 [amdgpu] [ +0.000185] ttm_bo_release+0x4c6/0x580 [ttm] [ +0.000010] amdgpu_bo_unref+0x1a/0x30 [amdgpu] [ +0.000183] amdgpu_vm_free_table+0x76/0xa0 [amdgpu] [ +0.000189] amdgpu_vm_free_pts+0xb8/0xf0 [amdgpu] [ +0.000189] amdgpu_vm_update_ptes+0x411/0x770 [amdgpu] [ +0.000191] amdgpu_vm_bo_update_mapping+0x324/0x4f0 [amdgpu] [ +0.000191] amdgpu_vm_bo_update+0x251/0x610 [amdgpu] [ +0.000191] update_gpuvm_pte+0xcc/0x290 [amdgpu] [ +0.000229] ? amdgpu_vm_bo_map+0xd7/0x130 [amdgpu] [ +0.000190] amdgpu_amdkfd_gpuvm_map_memory_to_gpu+0x912/0xf60 [amdgpu] [ +0.000234] kfd_ioctl_map_memory_to_gpu+0x182/0x320 [amdgpu] [ +0.000218] kfd_ioctl+0x2b9/0x600 [amdgpu] [ +0.000216] ? kfd_ioctl_unmap_memory_from_gpu+0x270/0x270 [amdgpu] [ +0.000216] ? lock_release+0x13f/0x270 [ +0.000006] ? __fget_files+0x107/0x1e0 [ +0.000007] __x64_sys_ioctl+0x8b/0xd0 [ +0.000007] do_syscall_64+0x36/0x70 [ +0.000004] entry_SYSCALL_64_after_hwframe+0x44/0xae [ +0.000007] RIP: 0033:0x7fbff90a7317 [ +0.000004] Code: b3 66 90 48 8b 05 71 4b 2d 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 41 4b 2d 00 f7 d8 64 89 01 48 [ +0.000005] RSP: 002b:00007fbe301fe648 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ +0.000006] RAX: ffffffffffffffda RBX: 00007fbcc402d820 RCX: 00007fbff90a7317 [ +0.000003] RDX: 00007fbe301fe690 RSI: 00000000c0184b18 RDI: 0000000000000004 [ +0.000003] RBP: 00007fbe301fe690 R08: 0000000000000000 R09: 00007fbcc402d880 [ +0.000003] R10: 0000000002001000 R11: 0000000000000246 R12: 00000000c0184b18 [ +0.000003] R13: 0000000000000004 R14: 00007fbf689593a0 R15: 00007fbcc402d820 Cc: Christian König <christian.koenig@amd.com> Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Alex Deucher <Alexander.Deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ef27324 ] Our detector found a concurrent use-after-free bug when detaching an NCI device. The main reason for this bug is the unexpected scheduling between the used delayed mechanism (timer and workqueue). The race can be demonstrated below: Thread-1 Thread-2 | nci_dev_up() | nci_open_device() | __nci_request(nci_reset_req) | nci_send_cmd | queue_work(cmd_work) nci_unregister_device() | nci_close_device() | ... del_timer_sync(cmd_timer)[1] | ... | Worker nci_free_device() | nci_cmd_work() kfree(ndev)[3] | mod_timer(cmd_timer)[2] In short, the cleanup routine thought that the cmd_timer has already been detached by [1] but the mod_timer can re-attach the timer [2], even it is already released [3], resulting in UAF. This UAF is easy to trigger, crash trace by POC is like below [ 66.703713] ================================================================== [ 66.703974] BUG: KASAN: use-after-free in enqueue_timer+0x448/0x490 [ 66.703974] Write of size 8 at addr ffff888009fb7058 by task kworker/u4:1/33 [ 66.703974] [ 66.703974] CPU: 1 PID: 33 Comm: kworker/u4:1 Not tainted 5.18.0-rc2 #5 [ 66.703974] Workqueue: nfc2_nci_cmd_wq nci_cmd_work [ 66.703974] Call Trace: [ 66.703974] <TASK> [ 66.703974] dump_stack_lvl+0x57/0x7d [ 66.703974] print_report.cold+0x5e/0x5db [ 66.703974] ? enqueue_timer+0x448/0x490 [ 66.703974] kasan_report+0xbe/0x1c0 [ 66.703974] ? enqueue_timer+0x448/0x490 [ 66.703974] enqueue_timer+0x448/0x490 [ 66.703974] __mod_timer+0x5e6/0xb80 [ 66.703974] ? mark_held_locks+0x9e/0xe0 [ 66.703974] ? try_to_del_timer_sync+0xf0/0xf0 [ 66.703974] ? lockdep_hardirqs_on_prepare+0x17b/0x410 [ 66.703974] ? queue_work_on+0x61/0x80 [ 66.703974] ? lockdep_hardirqs_on+0xbf/0x130 [ 66.703974] process_one_work+0x8bb/0x1510 [ 66.703974] ? lockdep_hardirqs_on_prepare+0x410/0x410 [ 66.703974] ? pwq_dec_nr_in_flight+0x230/0x230 [ 66.703974] ? rwlock_bug.part.0+0x90/0x90 [ 66.703974] ? _raw_spin_lock_irq+0x41/0x50 [ 66.703974] worker_thread+0x575/0x1190 [ 66.703974] ? process_one_work+0x1510/0x1510 [ 66.703974] kthread+0x2a0/0x340 [ 66.703974] ? kthread_complete_and_exit+0x20/0x20 [ 66.703974] ret_from_fork+0x22/0x30 [ 66.703974] </TASK> [ 66.703974] [ 66.703974] Allocated by task 267: [ 66.703974] kasan_save_stack+0x1e/0x40 [ 66.703974] __kasan_kmalloc+0x81/0xa0 [ 66.703974] nci_allocate_device+0xd3/0x390 [ 66.703974] nfcmrvl_nci_register_dev+0x183/0x2c0 [ 66.703974] nfcmrvl_nci_uart_open+0xf2/0x1dd [ 66.703974] nci_uart_tty_ioctl+0x2c3/0x4a0 [ 66.703974] tty_ioctl+0x764/0x1310 [ 66.703974] __x64_sys_ioctl+0x122/0x190 [ 66.703974] do_syscall_64+0x3b/0x90 [ 66.703974] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 66.703974] [ 66.703974] Freed by task 406: [ 66.703974] kasan_save_stack+0x1e/0x40 [ 66.703974] kasan_set_track+0x21/0x30 [ 66.703974] kasan_set_free_info+0x20/0x30 [ 66.703974] __kasan_slab_free+0x108/0x170 [ 66.703974] kfree+0xb0/0x330 [ 66.703974] nfcmrvl_nci_unregister_dev+0x90/0xd0 [ 66.703974] nci_uart_tty_close+0xdf/0x180 [ 66.703974] tty_ldisc_kill+0x73/0x110 [ 66.703974] tty_ldisc_hangup+0x281/0x5b0 [ 66.703974] __tty_hangup.part.0+0x431/0x890 [ 66.703974] tty_release+0x3a8/0xc80 [ 66.703974] __fput+0x1f0/0x8c0 [ 66.703974] task_work_run+0xc9/0x170 [ 66.703974] exit_to_user_mode_prepare+0x194/0x1a0 [ 66.703974] syscall_exit_to_user_mode+0x19/0x50 [ 66.703974] do_syscall_64+0x48/0x90 [ 66.703974] entry_SYSCALL_64_after_hwframe+0x44/0xae To fix the UAF, this patch adds flush_workqueue() to ensure the nci_cmd_work is finished before the following del_timer_sync. This combination will promise the timer is actually detached. Fixes: 6a2968a ("NFC: basic NCI protocol implementation") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit af68656 ] While handling PCI errors (AER flow) driver tries to disable NAPI [napi_disable()] after NAPI is deleted [__netif_napi_del()] which causes unexpected system hang/crash. System message log shows the following: ======================================= [ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures. [ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)' [ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->error_detected(IO frozen) [ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports: 'need reset' [ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking bnx2x->error_detected(IO frozen) [ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports: 'need reset' [ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset' [ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow: [ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows: [ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow: [ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows: [ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset' [ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->slot_reset() [ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing... [ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset --> driver unload Uninterruptible tasks ===================== crash> ps | grep UN 213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd] 215 2 0 c000000004c80000 UN 0.0 0 0 [kworker/0:2] 2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd 4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty 4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty 32423 2 26 c00000020038c580 UN 0.0 0 0 [kworker/26:3] 32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd 32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail 33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail 33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup 33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd 33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail 33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd EEH handler hung while bnx2x sleeping and holding RTNL lock =========================================================== crash> bt 213 PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd" #0 [c000000004d477e0] __schedule at c000000000c70808 #1 [c000000004d478b0] schedule at c000000000c70ee0 #2 [c000000004d478e0] schedule_timeout at c000000000c76dec #3 [c000000004d479c0] msleep at c0000000002120cc #4 [c000000004d479f0] napi_disable at c000000000a06448 ^^^^^^^^^^^^^^^^ #5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x] #6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x] #7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc #8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8 #9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64 And the sleeping source code ============================ crash> dis -ls c000000000a06448 FILE: ../net/core/dev.c LINE: 6702 6697 { 6698 might_sleep(); 6699 set_bit(NAPI_STATE_DISABLE, &n->state); 6700 6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state)) * 6702 msleep(1); 6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state)) 6704 msleep(1); 6705 6706 hrtimer_cancel(&n->timer); 6707 6708 clear_bit(NAPI_STATE_DISABLE, &n->state); 6709 } EEH calls into bnx2x twice based on the system log above, first through bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes the following call chains: bnx2x_io_error_detected() +-> bnx2x_eeh_nic_unload() +-> bnx2x_del_all_napi() +-> __netif_napi_del() bnx2x_io_slot_reset() +-> bnx2x_netif_stop() +-> bnx2x_napi_disable() +->napi_disable() Fix this by correcting the sequence of NAPI APIs usage, that is delete the NAPI after disabling it. Fixes: 7fa6f34 ("bnx2x: AER revised") Reported-by: David Christensen <drc@linux.vnet.ibm.com> Tested-by: David Christensen <drc@linux.vnet.ibm.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 84a5358 ] The SRv6 layer allows defining HMAC data that can later be used to sign IPv6 Segment Routing Headers. This configuration is realised via netlink through four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual length of the SECRET attribute, it is possible to provide invalid combinations (e.g., secret = "", secretlen = 64). This case is not checked in the code and with an appropriately crafted netlink message, an out-of-bounds read of up to 64 bytes (max secret length) can occur past the skb end pointer and into skb_shared_info: Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 208 memcpy(hinfo->secret, secret, slen); (gdb) bt #0 seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208 STMicroelectronics#1 0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600, extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>, family=<optimized out>) at net/netlink/genetlink.c:731 STMicroelectronics#2 0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00, family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775 STMicroelectronics#3 genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792 STMicroelectronics#4 0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>) at net/netlink/af_netlink.c:2501 STMicroelectronics#5 0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803 STMicroelectronics#6 0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000) at net/netlink/af_netlink.c:1319 STMicroelectronics#7 netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>) at net/netlink/af_netlink.c:1345 STMicroelectronics#8 0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921 ... (gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end $1 = 0xffff88800b1b76c0 (gdb) p/x secret $2 = 0xffff88800b1b76c0 (gdb) p slen $3 = 64 '@' The OOB data can then be read back from userspace by dumping HMAC state. This commit fixes this by ensuring SECRETLEN cannot exceed the actual length of SECRET. Reported-by: Lucas Leong <wmliang.tw@gmail.com> Tested: verified that EINVAL is correctly returned when secretlen > len(secret) Fixes: 4f4853d ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 1b513f6 upstream. Syzkaller reported BUG_ON as follows: ------------[ cut here ]------------ kernel BUG at fs/ntfs/dir.c:86! invalid opcode: 0000 [STMicroelectronics#1] PREEMPT SMP KASAN PTI CPU: 3 PID: 758 Comm: a.out Not tainted 5.19.0-next-20220808 STMicroelectronics#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:ntfs_lookup_inode_by_name+0xd11/0x2d10 Code: ff e9 b9 01 00 00 e8 1e fe d6 fe 48 8b 7d 98 49 8d 5d 07 e8 91 85 29 ff 48 c7 45 98 00 00 00 00 e9 5a fb ff ff e8 ff fd d6 fe <0f> 0b e8 f8 fd d6 fe 0f 0b e8 f1 fd d6 fe 48 8b b5 50 ff ff ff 4c RSP: 0018:ffff888079607978 EFLAGS: 00010293 RAX: 0000000000000000 RBX: 0000000000008000 RCX: 0000000000000000 RDX: ffff88807cf10000 RSI: ffffffff82a4a081 RDI: 0000000000000003 RBP: ffff888079607a70 R08: 0000000000000001 R09: ffff88807a6d01d7 R10: ffffed100f4da03a R11: 0000000000000000 R12: ffff88800f0fb110 R13: ffff88800f0ee000 R14: ffff88800f0fb000 R15: 0000000000000001 FS: 00007f33b63c7540(0000) GS:ffff888108580000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f33b635c090 CR3: 000000000f39e005 CR4: 0000000000770ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> load_system_files+0x1f7f/0x3620 ntfs_fill_super+0xa01/0x1be0 mount_bdev+0x36a/0x440 ntfs_mount+0x3a/0x50 legacy_get_tree+0xfb/0x210 vfs_get_tree+0x8f/0x2f0 do_new_mount+0x30a/0x760 path_mount+0x4de/0x1880 __x64_sys_mount+0x2b3/0x340 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f33b62ff9ea Code: 48 8b 0d a9 f4 0b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 76 f4 0b 00 f7 d8 64 89 01 48 RSP: 002b:00007ffd0c471aa8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f33b62ff9ea RDX: 0000000020000000 RSI: 0000000020000100 RDI: 00007ffd0c471be0 RBP: 00007ffd0c471c60 R08: 00007ffd0c471ae0 R09: 00007ffd0c471c24 R10: 0000000000000000 R11: 0000000000000202 R12: 000055bac5afc160 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- Fix this by adding sanity check on extended system files' directory inode to ensure that it is directory, just like ntfs_extend_init() when mounting ntfs3. Link: https://lkml.kernel.org/r/20220809064730.2316892-1-chenxiaosong2@huawei.com Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com> Cc: Anton Altaparmakov <anton@tuxera.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

@Loose

commit 4abc996 upstream. Syzkaller managed to trigger concurrent calls to kernfs_remove_by_name_ns() for the same file resulting in a KASAN detected use-after-free. The race occurs when the root node is freed during kernfs_drain(). To prevent this acquire an additional reference for the root of the tree that is removed before calling __kernfs_remove(). Found by syzkaller with the following reproducer (slab_nomerge is required): syz_mount_image$ext4(0x0, &(0x7f0000000100)='./file0\x00', 0x100000, 0x0, 0x0, 0x0, 0x0) r0 = openat(0xffffffffffffff9c, &(0x7f0000000080)='/proc/self/exe\x00', 0x0, 0x0) close(r0) pipe2(&(0x7f0000000140)={0xffffffffffffffff, <r1=>0xffffffffffffffff}, 0x800) mount$9p_fd(0x0, &(0x7f0000000040)='./file0\x00', &(0x7f00000000c0), 0x408, &(0x7f0000000280)={'trans=fd,', {'rfdno', 0x3d, r0}, 0x2c, {'wfdno', 0x3d, r1}, 0x2c, {[{@cache_loose}, {@MMAP}, {@Loose}, {@Loose}, {@MMAP}], [{@Mask={'mask', 0x3d, '^MAY_EXEC'}}, {@FSMagic={'fsmagic', 0x3d, 0x10001}}, {@dont_hash}]}}) Sample report: ================================================================== BUG: KASAN: use-after-free in kernfs_type include/linux/kernfs.h:335 [inline] BUG: KASAN: use-after-free in kernfs_leftmost_descendant fs/kernfs/dir.c:1261 [inline] BUG: KASAN: use-after-free in __kernfs_remove.part.0+0x843/0x960 fs/kernfs/dir.c:1369 Read of size 2 at addr ffff8880088807f0 by task syz-executor.2/857 CPU: 0 PID: 857 Comm: syz-executor.2 Not tainted 6.0.0-rc3-00363-g7726d4c3e60b STMicroelectronics#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x6e/0x91 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:317 [inline] print_report.cold+0x5e/0x5e5 mm/kasan/report.c:433 kasan_report+0xa3/0x130 mm/kasan/report.c:495 kernfs_type include/linux/kernfs.h:335 [inline] kernfs_leftmost_descendant fs/kernfs/dir.c:1261 [inline] __kernfs_remove.part.0+0x843/0x960 fs/kernfs/dir.c:1369 __kernfs_remove fs/kernfs/dir.c:1356 [inline] kernfs_remove_by_name_ns+0x108/0x190 fs/kernfs/dir.c:1589 sysfs_slab_add+0x133/0x1e0 mm/slub.c:5943 __kmem_cache_create+0x3e0/0x550 mm/slub.c:4899 create_cache mm/slab_common.c:229 [inline] kmem_cache_create_usercopy+0x167/0x2a0 mm/slab_common.c:335 p9_client_create+0xd4d/0x1190 net/9p/client.c:993 v9fs_session_init+0x1e6/0x13c0 fs/9p/v9fs.c:408 v9fs_mount+0xb9/0xbd0 fs/9p/vfs_super.c:126 legacy_get_tree+0xf1/0x200 fs/fs_context.c:610 vfs_get_tree+0x85/0x2e0 fs/super.c:1530 do_new_mount fs/namespace.c:3040 [inline] path_mount+0x675/0x1d00 fs/namespace.c:3370 do_mount fs/namespace.c:3383 [inline] __do_sys_mount fs/namespace.c:3591 [inline] __se_sys_mount fs/namespace.c:3568 [inline] __x64_sys_mount+0x282/0x300 fs/namespace.c:3568 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f725f983aed Code: 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f725f0f7028 EFLAGS: 00000246 ORIG_RAX: 00000000000000a5 RAX: ffffffffffffffda RBX: 00007f725faa3f80 RCX: 00007f725f983aed RDX: 00000000200000c0 RSI: 0000000020000040 RDI: 0000000000000000 RBP: 00007f725f9f419c R08: 0000000020000280 R09: 0000000000000000 R10: 0000000000000408 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000006 R14: 00007f725faa3f80 R15: 00007f725f0d7000 </TASK> Allocated by task 855: kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:45 [inline] set_alloc_info mm/kasan/common.c:437 [inline] __kasan_slab_alloc+0x66/0x80 mm/kasan/common.c:470 kasan_slab_alloc include/linux/kasan.h:224 [inline] slab_post_alloc_hook mm/slab.h:727 [inline] slab_alloc_node mm/slub.c:3243 [inline] slab_alloc mm/slub.c:3251 [inline] __kmem_cache_alloc_lru mm/slub.c:3258 [inline] kmem_cache_alloc+0xbf/0x200 mm/slub.c:3268 kmem_cache_zalloc include/linux/slab.h:723 [inline] __kernfs_new_node+0xd4/0x680 fs/kernfs/dir.c:593 kernfs_new_node fs/kernfs/dir.c:655 [inline] kernfs_create_dir_ns+0x9c/0x220 fs/kernfs/dir.c:1010 sysfs_create_dir_ns+0x127/0x290 fs/sysfs/dir.c:59 create_dir lib/kobject.c:63 [inline] kobject_add_internal+0x24a/0x8d0 lib/kobject.c:223 kobject_add_varg lib/kobject.c:358 [inline] kobject_init_and_add+0x101/0x160 lib/kobject.c:441 sysfs_slab_add+0x156/0x1e0 mm/slub.c:5954 __kmem_cache_create+0x3e0/0x550 mm/slub.c:4899 create_cache mm/slab_common.c:229 [inline] kmem_cache_create_usercopy+0x167/0x2a0 mm/slab_common.c:335 p9_client_create+0xd4d/0x1190 net/9p/client.c:993 v9fs_session_init+0x1e6/0x13c0 fs/9p/v9fs.c:408 v9fs_mount+0xb9/0xbd0 fs/9p/vfs_super.c:126 legacy_get_tree+0xf1/0x200 fs/fs_context.c:610 vfs_get_tree+0x85/0x2e0 fs/super.c:1530 do_new_mount fs/namespace.c:3040 [inline] path_mount+0x675/0x1d00 fs/namespace.c:3370 do_mount fs/namespace.c:3383 [inline] __do_sys_mount fs/namespace.c:3591 [inline] __se_sys_mount fs/namespace.c:3568 [inline] __x64_sys_mount+0x282/0x300 fs/namespace.c:3568 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd Freed by task 857: kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38 kasan_set_track+0x21/0x30 mm/kasan/common.c:45 kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:370 ____kasan_slab_free mm/kasan/common.c:367 [inline] ____kasan_slab_free mm/kasan/common.c:329 [inline] __kasan_slab_free+0x108/0x190 mm/kasan/common.c:375 kasan_slab_free include/linux/kasan.h:200 [inline] slab_free_hook mm/slub.c:1754 [inline] slab_free_freelist_hook mm/slub.c:1780 [inline] slab_free mm/slub.c:3534 [inline] kmem_cache_free+0x9c/0x340 mm/slub.c:3551 kernfs_put.part.0+0x2b2/0x520 fs/kernfs/dir.c:547 kernfs_put+0x42/0x50 fs/kernfs/dir.c:521 __kernfs_remove.part.0+0x72d/0x960 fs/kernfs/dir.c:1407 __kernfs_remove fs/kernfs/dir.c:1356 [inline] kernfs_remove_by_name_ns+0x108/0x190 fs/kernfs/dir.c:1589 sysfs_slab_add+0x133/0x1e0 mm/slub.c:5943 __kmem_cache_create+0x3e0/0x550 mm/slub.c:4899 create_cache mm/slab_common.c:229 [inline] kmem_cache_create_usercopy+0x167/0x2a0 mm/slab_common.c:335 p9_client_create+0xd4d/0x1190 net/9p/client.c:993 v9fs_session_init+0x1e6/0x13c0 fs/9p/v9fs.c:408 v9fs_mount+0xb9/0xbd0 fs/9p/vfs_super.c:126 legacy_get_tree+0xf1/0x200 fs/fs_context.c:610 vfs_get_tree+0x85/0x2e0 fs/super.c:1530 do_new_mount fs/namespace.c:3040 [inline] path_mount+0x675/0x1d00 fs/namespace.c:3370 do_mount fs/namespace.c:3383 [inline] __do_sys_mount fs/namespace.c:3591 [inline] __se_sys_mount fs/namespace.c:3568 [inline] __x64_sys_mount+0x282/0x300 fs/namespace.c:3568 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd The buggy address belongs to the object at ffff888008880780 which belongs to the cache kernfs_node_cache of size 128 The buggy address is located 112 bytes inside of 128-byte region [ffff888008880780, ffff888008880800) The buggy address belongs to the physical page: page:00000000732833f8 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8880 flags: 0x100000000000200(slab|node=0|zone=1) raw: 0100000000000200 0000000000000000 dead000000000122 ffff888001147280 raw: 0000000000000000 0000000000150015 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888008880680: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb ffff888008880700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc >ffff888008880780: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff888008880800: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb ffff888008880880: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ================================================================== Acked-by: Tejun Heo <tj@kernel.org> Cc: stable <stable@kernel.org> # -rc3 Signed-off-by: Christian A. Ehrhardt <lk@c--e.de> Link: https://lore.kernel.org/r/20220913121723.691454-1-lk@c--e.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…l/git/netfilter/nf Florisn Westphal says: ==================== These are netfilter fixes for the *net* tree. First patch resolves a false-positive lockdep splat: rcu_dereference is used outside of rcu read lock. Let lockdep validate that the transaction mutex is locked. Second patch fixes a kdoc warning added in previous PR. Third patch fixes a memory leak: The catchall element isn't disabled correctly, this allows userspace to deactivate the element again. This results in refcount underflow which in turn prevents memory release. This was always broken since the feature was added in 5.13. Patch 4 fixes an incorrect change in the previous pull request: Adding a duplicate key to a set should work if the duplicate key has expired, restore this behaviour. All from myself. Patch STMicroelectronics#5 resolves an old historic artifact in sctp conntrack: a 300ms timeout for shutdown_ack. Increase this to 3s. From Xin Long. Patch STMicroelectronics#6 fixes a sysctl data race in ipvs, two threads can clobber the sysctl value, from Sishuai Gong. This is a day-0 bug that predates git history. Patches 7, 8 and 9, from Pablo Neira Ayuso, are also followups for the previous GC rework in nf_tables: The netlink notifier and the netns exit path must both increment the gc worker seqcount, else worker may encounter stale (free'd) pointers. ================ Signed-off-by: David S. Miller <davem@davemloft.net>

[ Upstream commit 735a02f ] When queuing parameters fails, current code bails out without deleting the corresponding vb2 buffer from the driver buffer list, but the buffer is returned to vb2. This leads to stale list entries and a crash when the driver stops streaming: [ 224.935561] ipu3-imgu 0000:00:05.0: set parameters failed. [ 224.998932] ipu3-imgu 0000:00:05.0: set parameters failed. [ 225.064430] ipu3-imgu 0000:00:05.0: set parameters failed. [ 225.128534] ipu3-imgu 0000:00:05.0: set parameters failed. [ 225.194945] ipu3-imgu 0000:00:05.0: set parameters failed. [ 225.360363] ------------[ cut here ]------------ [ 225.360372] WARNING: CPU: 0 PID: 6704 at drivers/media/common/videobuf2/videobuf2-core.c:927 vb2_buffer_done+0x20f/0x21a [videobuf2_common] [ 225.360374] Modules linked in: snd_seq_dummy snd_seq snd_seq_device veth bridge stp llc tun nf_nat_tftp nf_conntrack_tftp nf_nat_ftp nf_conntrack_ftp esp6 ah6 ip6t_REJECT ip6t_ipv6header cmac rfcomm uinput ipu3_imgu(C) ipu3_cio2 iova videobuf2_v4l2 videobuf2_common videobuf2_dma_sg videobuf2_memops ov13858 ov5670 v4l2_fwnode dw9714 acpi_als xt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_light_prox cros_ec_sensors cros_ec_sensors_core industrialio_triggered_buffer kfifo_buf industrialio cros_ec_sensorsupport cdc_ether btusb btrtl btintel btbcm usbnet bluetooth ecdh_generic ecc hid_google_hammer iwlmvm iwl7000_mac80211 r8152 mii lzo_rle lzo_compress iwlwifi zram cfg80211 joydev [ 225.360400] CPU: 0 PID: 6704 Comm: CameraDeviceOps Tainted: G C 5.4.30 STMicroelectronics#5 [ 225.360402] Hardware name: HP Soraka/Soraka, BIOS Google_Soraka.10431.106.0 12/03/2019 [ 225.360405] RIP: 0010:vb2_buffer_done+0x20f/0x21a [videobuf2_common] [ 225.360408] Code: 5e 41 5f 5d e9 e0 16 5a d4 41 8b 55 08 48 c7 c7 8f 8b 5c c0 48 c7 c6 36 9a 5c c0 44 89 f9 31 c0 e8 a5 1c 5b d4 e9 53 fe ff ff <0f> 0b eb a3 e8 12 d7 43 d4 eb 97 0f 1f 44 00 00 55 48 89 e5 41 56 [ 225.360410] RSP: 0018:ffff9468ab32fba8 EFLAGS: 00010297 [ 225.360412] RAX: ffff8aa7a51577a8 RBX: dead000000000122 RCX: ffff8aa7a51577a8 [ 225.360414] RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffff8aa7a5157400 [ 225.360416] RBP: ffff9468ab32fbd8 R08: ffff8aa64e47e600 R09: 0000000000000000 [ 225.360418] R10: 0000000000000000 R11: ffffffffc06036e6 R12: dead000000000100 [ 225.360420] R13: ffff8aa7820f1940 R14: ffff8aa7a51577a8 R15: 0000000000000006 [ 225.360422] FS: 00007c1146ffd700(0000) GS:ffff8aa7baa00000(0000) knlGS:0000000000000000 [ 225.360424] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 225.360426] CR2: 00007aea3473a000 CR3: 00000000537d6004 CR4: 00000000003606f0 [ 225.360427] Call Trace: [ 225.360434] imgu_return_all_buffers+0x6f/0x8e [ipu3_imgu] [ 225.360438] imgu_vb2_stop_streaming+0xd6/0xf0 [ipu3_imgu] [ 225.360441] __vb2_queue_cancel+0x33/0x22d [videobuf2_common] [ 225.360443] vb2_core_streamoff+0x16/0x78 [videobuf2_common] [ 225.360448] __video_do_ioctl+0x33d/0x42a [ 225.360452] video_usercopy+0x34a/0x615 [ 225.360455] ? video_ioctl2+0x16/0x16 [ 225.360458] v4l2_ioctl+0x46/0x53 [ 225.360462] do_vfs_ioctl+0x50a/0x787 [ 225.360465] ksys_ioctl+0x58/0x83 [ 225.360468] __x64_sys_ioctl+0x1a/0x1e [ 225.360470] do_syscall_64+0x54/0x68 [ 225.360474] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 225.360476] RIP: 0033:0x7c118030f497 [ 225.360479] Code: 8a 66 90 48 8b 05 d1 d9 2b 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a1 d9 2b 00 f7 d8 64 89 01 48 [ 225.360480] RSP: 002b:00007c1146ffa5a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 225.360483] RAX: ffffffffffffffda RBX: 00007c1140010018 RCX: 00007c118030f497 [ 225.360484] RDX: 00007c114001019c RSI: 0000000040045613 RDI: 000000000000004c [ 225.360486] RBP: 00007c1146ffa700 R08: 00007c1140010048 R09: 0000000000000000 [ 225.360488] R10: 0000000000000000 R11: 0000000000000246 R12: 00007c11400101b0 [ 225.360489] R13: 00007c1140010200 R14: 00007c1140010048 R15: 0000000000000001 [ 225.360492] ---[ end trace 73625ecfbd1c930e ]--- [ 225.360498] general protection fault: 0000 [STMicroelectronics#1] PREEMPT SMP PTI [ 225.360501] CPU: 0 PID: 6704 Comm: CameraDeviceOps Tainted: G WC 5.4.30 STMicroelectronics#5 [ 225.360502] Hardware name: HP Soraka/Soraka, BIOS Google_Soraka.10431.106.0 12/03/2019 [ 225.360505] RIP: 0010:imgu_return_all_buffers+0x52/0x8e [ipu3_imgu] [ 225.360507] Code: d4 49 8b 85 70 0a 00 00 49 81 c5 70 0a 00 00 49 39 c5 74 3b 49 bc 00 01 00 00 00 00 ad de 49 8d 5c 24 22 4c 8b 30 48 8b 48 08 <49> 89 4e 08 4c 89 31 4c 89 20 48 89 58 08 48 8d b8 58 fc ff ff 44 [ 225.360509] RSP: 0018:ffff9468ab32fbe8 EFLAGS: 00010293 [ 225.360511] RAX: ffff8aa7a51577a8 RBX: dead000000000122 RCX: dead000000000122 [ 225.360512] RDX: 0000000000000000 RSI: 0000000000000006 RDI: ffff8aa7a5157400 [ 225.360514] RBP: ffff9468ab32fc18 R08: ffff8aa64e47e600 R09: 0000000000000000 [ 225.360515] R10: 0000000000000000 R11: ffffffffc06036e6 R12: dead000000000100 [ 225.360517] R13: ffff8aa7820f1940 R14: dead000000000100 R15: 0000000000000006 [ 225.360519] FS: 00007c1146ffd700(0000) GS:ffff8aa7baa00000(0000) knlGS:0000000000000000 [ 225.360521] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 225.360523] CR2: 00007aea3473a000 CR3: 00000000537d6004 CR4: 00000000003606f0 [ 225.360525] Call Trace: [ 225.360528] imgu_vb2_stop_streaming+0xd6/0xf0 [ipu3_imgu] [ 225.360531] __vb2_queue_cancel+0x33/0x22d [videobuf2_common] [ 225.360534] vb2_core_streamoff+0x16/0x78 [videobuf2_common] [ 225.360537] __video_do_ioctl+0x33d/0x42a [ 225.360540] video_usercopy+0x34a/0x615 [ 225.360542] ? video_ioctl2+0x16/0x16 [ 225.360546] v4l2_ioctl+0x46/0x53 [ 225.360548] do_vfs_ioctl+0x50a/0x787 [ 225.360551] ksys_ioctl+0x58/0x83 [ 225.360554] __x64_sys_ioctl+0x1a/0x1e [ 225.360556] do_syscall_64+0x54/0x68 [ 225.360559] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 225.360561] RIP: 0033:0x7c118030f497 [ 225.360563] Code: 8a 66 90 48 8b 05 d1 d9 2b 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a1 d9 2b 00 f7 d8 64 89 01 48 [ 225.360565] RSP: 002b:00007c1146ffa5a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 225.360567] RAX: ffffffffffffffda RBX: 00007c1140010018 RCX: 00007c118030f497 [ 225.360569] RDX: 00007c114001019c RSI: 0000000040045613 RDI: 000000000000004c [ 225.360570] RBP: 00007c1146ffa700 R08: 00007c1140010048 R09: 0000000000000000 [ 225.360572] R10: 0000000000000000 R11: 0000000000000246 R12: 00007c11400101b0 [ 225.360574] R13: 00007c1140010200 R14: 00007c1140010048 R15: 0000000000000001 [ 225.360576] Modules linked in: snd_seq_dummy snd_seq snd_seq_device veth bridge stp llc tun nf_nat_tftp nf_conntrack_tftp nf_nat_ftp nf_conntrack_ftp esp6 ah6 ip6t_REJECT ip6t_ipv6header cmac rfcomm uinput ipu3_imgu(C) ipu3_cio2 iova videobuf2_v4l2 videobuf2_common videobuf2_dma_sg videobuf2_memops ov13858 ov567 Fix this by moving the list_del() call just below the list_first_entry() call when the buffer no longer needs to be in the list. Fixes: 8ecc7c9 ("media: staging/intel-ipu3: parameter buffer refactoring") Signed-off-by: Tomasz Figa <tfiga@chromium.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 467dc47 upstream. When doing a buffered write we always try to reserve data space for it, even when the file has the NOCOW bit set or the write falls into a file range covered by a prealloc extent. This is done both because it is expensive to check if we can do a nocow write (checking if an extent is shared through reflinks or if there's a hole in the range for example), and because when writeback starts we might actually need to fallback to COW mode (for example the block group containing the target extents was turned into RO mode due to a scrub or balance). When we are unable to reserve data space we check if we can do a nocow write, and if we can, we proceed with dirtying the pages and setting up the range for delalloc. In this case the bytes_may_use counter of the data space_info object is not incremented, unlike in the case where we are able to reserve data space (done through btrfs_check_data_free_space() which calls btrfs_alloc_data_chunk_ondemand()). Later when running delalloc we attempt to start writeback in nocow mode but we might revert back to cow mode, for example because in the meanwhile a block group was turned into RO mode by a scrub or relocation. The cow path after successfully allocating an extent ends up calling btrfs_add_reserved_bytes(), which expects the bytes_may_use counter of the data space_info object to have been incremented before - but we did not do it when the buffered write started, since there was not enough available data space. So btrfs_add_reserved_bytes() ends up decrementing the bytes_may_use counter anyway, and when the counter's current value is smaller then the size of the allocated extent we get a stack trace like the following: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 20138 at fs/btrfs/space-info.h:115 btrfs_add_reserved_bytes+0x3d6/0x4e0 [btrfs] Modules linked in: btrfs blake2b_generic xor raid6_pq libcrc32c (...) CPU: 0 PID: 20138 Comm: kworker/u8:15 Not tainted 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 Workqueue: writeback wb_workfn (flush-btrfs-1754) RIP: 0010:btrfs_add_reserved_bytes+0x3d6/0x4e0 [btrfs] Code: ff ff 48 (...) RSP: 0018:ffffbda18a4b3568 EFLAGS: 00010287 RAX: 0000000000000000 RBX: ffff9ca076f5d800 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000000 RDI: ffff9ca068470410 RBP: fffffffffffff000 R08: 0000000000000001 R09: 0000000000000000 R10: ffff9ca079d58040 R11: 0000000000000000 R12: ffff9ca068470400 R13: ffff9ca0408b2000 R14: 0000000000001000 R15: ffff9ca076f5d800 FS: 0000000000000000(0000) GS:ffff9ca07a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005605dbfe7048 CR3: 0000000138570006 CR4: 00000000003606f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: find_free_extent+0x4a0/0x16c0 [btrfs] btrfs_reserve_extent+0x91/0x180 [btrfs] cow_file_range+0x12d/0x490 [btrfs] run_delalloc_nocow+0x341/0xa40 [btrfs] btrfs_run_delalloc_range+0x1ea/0x6d0 [btrfs] ? find_lock_delalloc_range+0x221/0x250 [btrfs] writepage_delalloc+0xe8/0x150 [btrfs] __extent_writepage+0xe8/0x4c0 [btrfs] extent_write_cache_pages+0x237/0x530 [btrfs] ? btrfs_wq_submit_bio+0x9f/0xc0 [btrfs] extent_writepages+0x44/0xa0 [btrfs] do_writepages+0x23/0x80 __writeback_single_inode+0x59/0x700 writeback_sb_inodes+0x267/0x5f0 __writeback_inodes_wb+0x87/0xe0 wb_writeback+0x382/0x590 ? wb_workfn+0x4a2/0x6c0 wb_workfn+0x4a2/0x6c0 process_one_work+0x26d/0x6a0 worker_thread+0x4f/0x3e0 ? process_one_work+0x6a0/0x6a0 kthread+0x103/0x140 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x3a/0x50 irq event stamp: 0 hardirqs last enabled at (0): [<0000000000000000>] 0x0 hardirqs last disabled at (0): [<ffffffff94ebdedf>] copy_process+0x74f/0x2020 softirqs last enabled at (0): [<ffffffff94ebdedf>] copy_process+0x74f/0x2020 softirqs last disabled at (0): [<0000000000000000>] 0x0 ---[ end trace f9f6ef8ec4cd8ec9 ]--- So to fix this, when falling back into cow mode check if space was not reserved, by testing for the bit EXTENT_NORESERVE in the respective file range, and if not, increment the bytes_may_use counter for the data space_info object. Also clear the EXTENT_NORESERVE bit from the range, so that if the cow path fails it decrements the bytes_may_use counter when clearing the delalloc range (through the btrfs_clear_delalloc_extent() callback). Fixes: 7ee9e44 ("Btrfs: check if we can nocow if we don't have data space") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…eout commit 2166e5e upstream. We always preallocate a data extent for writing a free space cache, which causes writeback to always try the nocow path first, since the free space inode has the prealloc bit set in its flags. However if the block group that contains the data extent for the space cache has been turned to RO mode due to a running scrub or balance for example, we have to fallback to the cow path. In that case once a new data extent is allocated we end up calling btrfs_add_reserved_bytes(), which decrements the counter named bytes_may_use from the data space_info object with the expection that this counter was previously incremented with the same amount (the size of the data extent). However when we started writeout of the space cache at cache_save_setup(), we incremented the value of the bytes_may_use counter through a call to btrfs_check_data_free_space() and then decremented it through a call to btrfs_prealloc_file_range_trans() immediately after. So when starting the writeback if we fallback to cow mode we have to increment the counter bytes_may_use of the data space_info again to compensate for the extent allocation done by the cow path. When this issue happens we are incorrectly decrementing the bytes_may_use counter and when its current value is smaller then the amount we try to subtract we end up with the following warning: ------------[ cut here ]------------ WARNING: CPU: 3 PID: 657 at fs/btrfs/space-info.h:115 btrfs_add_reserved_bytes+0x3d6/0x4e0 [btrfs] Modules linked in: btrfs blake2b_generic xor raid6_pq libcrc32c (...) CPU: 3 PID: 657 Comm: kworker/u8:7 Tainted: G W 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 Workqueue: writeback wb_workfn (flush-btrfs-1591) RIP: 0010:btrfs_add_reserved_bytes+0x3d6/0x4e0 [btrfs] Code: ff ff 48 (...) RSP: 0000:ffffa41608f13660 EFLAGS: 00010287 RAX: 0000000000001000 RBX: ffff9615b93ae400 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000000 RDI: ffff9615b96ab410 RBP: fffffffffffee000 R08: 0000000000000001 R09: 0000000000000000 R10: ffff961585e62a40 R11: 0000000000000000 R12: ffff9615b96ab400 R13: ffff9615a1a2a000 R14: 0000000000012000 R15: ffff9615b93ae400 FS: 0000000000000000(0000) GS:ffff9615bb200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055cbbc2ae178 CR3: 0000000115794006 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: find_free_extent+0x4a0/0x16c0 [btrfs] btrfs_reserve_extent+0x91/0x180 [btrfs] cow_file_range+0x12d/0x490 [btrfs] btrfs_run_delalloc_range+0x9f/0x6d0 [btrfs] ? find_lock_delalloc_range+0x221/0x250 [btrfs] writepage_delalloc+0xe8/0x150 [btrfs] __extent_writepage+0xe8/0x4c0 [btrfs] extent_write_cache_pages+0x237/0x530 [btrfs] extent_writepages+0x44/0xa0 [btrfs] do_writepages+0x23/0x80 __writeback_single_inode+0x59/0x700 writeback_sb_inodes+0x267/0x5f0 __writeback_inodes_wb+0x87/0xe0 wb_writeback+0x382/0x590 ? wb_workfn+0x4a2/0x6c0 wb_workfn+0x4a2/0x6c0 process_one_work+0x26d/0x6a0 worker_thread+0x4f/0x3e0 ? process_one_work+0x6a0/0x6a0 kthread+0x103/0x140 ? kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x3a/0x50 irq event stamp: 0 hardirqs last enabled at (0): [<0000000000000000>] 0x0 hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 softirqs last disabled at (0): [<0000000000000000>] 0x0 ---[ end trace bd7c03622e0b0a52 ]--- ------------[ cut here ]------------ So fix this by incrementing the bytes_may_use counter of the data space_info when we fallback to the cow path. If the cow path is successful the counter is decremented after extent allocation (by btrfs_add_reserved_bytes()), if it fails it ends up being decremented as well when clearing the delalloc range (extent_clear_unlock_delalloc()). This could be triggered sporadically by the test case btrfs/061 from fstests. Fixes: 82d5902 ("Btrfs: Support reading/writing on disk free ino cache") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…parallel commit 6bd335b upstream. When balance and scrub are running in parallel it is possible to end up with an underflow of the bytes_may_use counter of the data space_info object, which triggers a warning like the following: [134243.793196] BTRFS info (device sdc): relocating block group 1104150528 flags data [134243.806891] ------------[ cut here ]------------ [134243.807561] WARNING: CPU: 1 PID: 26884 at fs/btrfs/space-info.h:125 btrfs_add_reserved_bytes+0x1da/0x280 [btrfs] [134243.808819] Modules linked in: btrfs blake2b_generic xor (...) [134243.815779] CPU: 1 PID: 26884 Comm: kworker/u8:8 Tainted: G W 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 [134243.816944] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [134243.818389] Workqueue: writeback wb_workfn (flush-btrfs-108483) [134243.819186] RIP: 0010:btrfs_add_reserved_bytes+0x1da/0x280 [btrfs] [134243.819963] Code: 0b f2 85 (...) [134243.822271] RSP: 0018:ffffa4160aae7510 EFLAGS: 00010287 [134243.822929] RAX: 000000000000c000 RBX: ffff96159a8c1000 RCX: 0000000000000000 [134243.823816] RDX: 0000000000008000 RSI: 0000000000000000 RDI: ffff96158067a810 [134243.824742] RBP: ffff96158067a800 R08: 0000000000000001 R09: 0000000000000000 [134243.825636] R10: ffff961501432a40 R11: 0000000000000000 R12: 000000000000c000 [134243.826532] R13: 0000000000000001 R14: ffffffffffff4000 R15: ffff96158067a810 [134243.827432] FS: 0000000000000000(0000) GS:ffff9615baa00000(0000) knlGS:0000000000000000 [134243.828451] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [134243.829184] CR2: 000055bd7e414000 CR3: 00000001077be004 CR4: 00000000003606e0 [134243.830083] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [134243.830975] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [134243.831867] Call Trace: [134243.832211] find_free_extent+0x4a0/0x16c0 [btrfs] [134243.832846] btrfs_reserve_extent+0x91/0x180 [btrfs] [134243.833487] cow_file_range+0x12d/0x490 [btrfs] [134243.834080] fallback_to_cow+0x82/0x1b0 [btrfs] [134243.834689] ? release_extent_buffer+0x121/0x170 [btrfs] [134243.835370] run_delalloc_nocow+0x33f/0xa30 [btrfs] [134243.836032] btrfs_run_delalloc_range+0x1ea/0x6d0 [btrfs] [134243.836725] ? find_lock_delalloc_range+0x221/0x250 [btrfs] [134243.837450] writepage_delalloc+0xe8/0x150 [btrfs] [134243.838059] __extent_writepage+0xe8/0x4c0 [btrfs] [134243.838674] extent_write_cache_pages+0x237/0x530 [btrfs] [134243.839364] extent_writepages+0x44/0xa0 [btrfs] [134243.839946] do_writepages+0x23/0x80 [134243.840401] __writeback_single_inode+0x59/0x700 [134243.841006] writeback_sb_inodes+0x267/0x5f0 [134243.841548] __writeback_inodes_wb+0x87/0xe0 [134243.842091] wb_writeback+0x382/0x590 [134243.842574] ? wb_workfn+0x4a2/0x6c0 [134243.843030] wb_workfn+0x4a2/0x6c0 [134243.843468] process_one_work+0x26d/0x6a0 [134243.843978] worker_thread+0x4f/0x3e0 [134243.844452] ? process_one_work+0x6a0/0x6a0 [134243.844981] kthread+0x103/0x140 [134243.845400] ? kthread_create_worker_on_cpu+0x70/0x70 [134243.846030] ret_from_fork+0x3a/0x50 [134243.846494] irq event stamp: 0 [134243.846892] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [134243.847682] hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134243.848687] softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134243.849913] softirqs last disabled at (0): [<0000000000000000>] 0x0 [134243.850698] ---[ end trace bd7c03622e0b0a96 ]--- [134243.851335] ------------[ cut here ]------------ When relocating a data block group, for each extent allocated in the block group we preallocate another extent with the same size for the data relocation inode (we do it at prealloc_file_extent_cluster()). We reserve space by calling btrfs_check_data_free_space(), which ends up incrementing the data space_info's bytes_may_use counter, and then call btrfs_prealloc_file_range() to allocate the extent, which always decrements the bytes_may_use counter by the same amount. The expectation is that writeback of the data relocation inode always follows a NOCOW path, by writing into the preallocated extents. However, when starting writeback we might end up falling back into the COW path, because the block group that contains the preallocated extent was turned into RO mode by a scrub running in parallel. The COW path then calls the extent allocator which ends up calling btrfs_add_reserved_bytes(), and this function decrements the bytes_may_use counter of the data space_info object by an amount corresponding to the size of the allocated extent, despite we haven't previously incremented it. When the counter currently has a value smaller then the allocated extent we reset the counter to 0 and emit a warning, otherwise we just decrement it and slowly mess up with this counter which is crucial for space reservation, the end result can be granting reserved space to tasks when there isn't really enough free space, and having the tasks fail later in critical places where error handling consists of a transaction abort or hitting a BUG_ON(). Fix this by making sure that if we fallback to the COW path for a data relocation inode, we increment the bytes_may_use counter of the data space_info object. The COW path will then decrement it at btrfs_add_reserved_bytes() on success or through its error handling part by a call to extent_clear_unlock_delalloc() (which ends up calling btrfs_clear_delalloc_extent() that does the decrement operation) in case of an error. Test case btrfs/061 from fstests could sporadically trigger this. CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 432cd2a upstream. When running relocation of a data block group while scrub is running in parallel, it is possible that the relocation will fail and abort the current transaction with an -EINVAL error: [134243.988595] BTRFS info (device sdc): found 14 extents, stage: move data extents [134243.999871] ------------[ cut here ]------------ [134244.000741] BTRFS: Transaction aborted (error -22) [134244.001692] WARNING: CPU: 0 PID: 26954 at fs/btrfs/ctree.c:1071 __btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.003380] Modules linked in: btrfs blake2b_generic xor raid6_pq (...) [134244.012577] CPU: 0 PID: 26954 Comm: btrfs Tainted: G W 5.6.0-rc7-btrfs-next-58 STMicroelectronics#5 [134244.014162] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [134244.016184] RIP: 0010:__btrfs_cow_block+0x6a7/0x790 [btrfs] [134244.017151] Code: 48 c7 c7 (...) [134244.020549] RSP: 0018:ffffa41607863888 EFLAGS: 00010286 [134244.021515] RAX: 0000000000000000 RBX: ffff9614bdfe09c8 RCX: 0000000000000000 [134244.022822] RDX: 0000000000000001 RSI: ffffffffb3d63980 RDI: 0000000000000001 [134244.024124] RBP: ffff961589e8c000 R08: 0000000000000000 R09: 0000000000000001 [134244.025424] R10: ffffffffc0ae5955 R11: 0000000000000000 R12: ffff9614bd530d08 [134244.026725] R13: ffff9614ced41b88 R14: ffff9614bdfe2a48 R15: 0000000000000000 [134244.028024] FS: 00007f29b63c08c0(0000) GS:ffff9615ba600000(0000) knlGS:0000000000000000 [134244.029491] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [134244.030560] CR2: 00007f4eb339b000 CR3: 0000000130d6e006 CR4: 00000000003606f0 [134244.031997] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [134244.033153] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [134244.034484] Call Trace: [134244.034984] btrfs_cow_block+0x12b/0x2b0 [btrfs] [134244.035859] do_relocation+0x30b/0x790 [btrfs] [134244.036681] ? do_raw_spin_unlock+0x49/0xc0 [134244.037460] ? _raw_spin_unlock+0x29/0x40 [134244.038235] relocate_tree_blocks+0x37b/0x730 [btrfs] [134244.039245] relocate_block_group+0x388/0x770 [btrfs] [134244.040228] btrfs_relocate_block_group+0x161/0x2e0 [btrfs] [134244.041323] btrfs_relocate_chunk+0x36/0x110 [btrfs] [134244.041345] btrfs_balance+0xc06/0x1860 [btrfs] [134244.043382] ? btrfs_ioctl_balance+0x27c/0x310 [btrfs] [134244.045586] btrfs_ioctl_balance+0x1ed/0x310 [btrfs] [134244.045611] btrfs_ioctl+0x1880/0x3760 [btrfs] [134244.049043] ? do_raw_spin_unlock+0x49/0xc0 [134244.049838] ? _raw_spin_unlock+0x29/0x40 [134244.050587] ? __handle_mm_fault+0x11b3/0x14b0 [134244.051417] ? ksys_ioctl+0x92/0xb0 [134244.052070] ksys_ioctl+0x92/0xb0 [134244.052701] ? trace_hardirqs_off_thunk+0x1a/0x1c [134244.053511] __x64_sys_ioctl+0x16/0x20 [134244.054206] do_syscall_64+0x5c/0x280 [134244.054891] entry_SYSCALL_64_after_hwframe+0x49/0xbe [134244.055819] RIP: 0033:0x7f29b51c9dd7 [134244.056491] Code: 00 00 00 (...) [134244.059767] RSP: 002b:00007ffcccc1dd08 EFLAGS: 00000202 ORIG_RAX: 0000000000000010 [134244.061168] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f29b51c9dd7 [134244.062474] RDX: 00007ffcccc1dda0 RSI: 00000000c4009420 RDI: 0000000000000003 [134244.063771] RBP: 0000000000000003 R08: 00005565cea4b000 R09: 0000000000000000 [134244.065032] R10: 0000000000000541 R11: 0000000000000202 R12: 00007ffcccc2060a [134244.066327] R13: 00007ffcccc1dda0 R14: 0000000000000002 R15: 00007ffcccc1dec0 [134244.067626] irq event stamp: 0 [134244.068202] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [134244.069351] hardirqs last disabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.070909] softirqs last enabled at (0): [<ffffffffb2abdedf>] copy_process+0x74f/0x2020 [134244.072392] softirqs last disabled at (0): [<0000000000000000>] 0x0 [134244.073432] ---[ end trace bd7c03622e0b0a99 ]--- The -EINVAL error comes from the following chain of function calls: __btrfs_cow_block() <-- aborts the transaction btrfs_reloc_cow_block() replace_file_extents() get_new_location() <-- returns -EINVAL When relocating a data block group, for each allocated extent of the block group, we preallocate another extent (at prealloc_file_extent_cluster()), associated with the data relocation inode, and then dirty all its pages. These preallocated extents have, and must have, the same size that extents from the data block group being relocated have. Later before we start the relocation stage that updates pointers (bytenr field of file extent items) to point to the the new extents, we trigger writeback for the data relocation inode. The expectation is that writeback will write the pages to the previously preallocated extents, that it follows the NOCOW path. That is generally the case, however, if a scrub is running it may have turned the block group that contains those extents into RO mode, in which case writeback falls back to the COW path. However in the COW path instead of allocating exactly one extent with the expected size, the allocator may end up allocating several smaller extents due to free space fragmentation - because we tell it at cow_file_range() that the minimum allocation size can match the filesystem's sector size. This later breaks the relocation's expectation that an extent associated to a file extent item in the data relocation inode has the same size as the respective extent pointed by a file extent item in another tree - in this case the extent to which the relocation inode poins to is smaller, causing relocation.c:get_new_location() to return -EINVAL. For example, if we are relocating a data block group X that has a logical address of X and the block group has an extent allocated at the logical address X + 128KiB with a size of 64KiB: 1) At prealloc_file_extent_cluster() we allocate an extent for the data relocation inode with a size of 64KiB and associate it to the file offset 128KiB (X + 128KiB - X) of the data relocation inode. This preallocated extent was allocated at block group Z; 2) A scrub running in parallel turns block group Z into RO mode and starts scrubing its extents; 3) Relocation triggers writeback for the data relocation inode; 4) When running delalloc (btrfs_run_delalloc_range()), we try first the NOCOW path because the data relocation inode has BTRFS_INODE_PREALLOC set in its flags. However, because block group Z is in RO mode, the NOCOW path (run_delalloc_nocow()) falls back into the COW path, by calling cow_file_range(); 5) At cow_file_range(), in the first iteration of the while loop we call btrfs_reserve_extent() to allocate a 64KiB extent and pass it a minimum allocation size of 4KiB (fs_info->sectorsize). Due to free space fragmentation, btrfs_reserve_extent() ends up allocating two extents of 32KiB each, each one on a different iteration of that while loop; 6) Writeback of the data relocation inode completes; 7) Relocation proceeds and ends up at relocation.c:replace_file_extents(), with a leaf which has a file extent item that points to the data extent from block group X, that has a logical address (bytenr) of X + 128KiB and a size of 64KiB. Then it calls get_new_location(), which does a lookup in the data relocation tree for a file extent item starting at offset 128KiB (X + 128KiB - X) and belonging to the data relocation inode. It finds a corresponding file extent item, however that item points to an extent that has a size of 32KiB, which doesn't match the expected size of 64KiB, resuling in -EINVAL being returned from this function and propagated up to __btrfs_cow_block(), which aborts the current transaction. To fix this make sure that at cow_file_range() when we call the allocator we pass it a minimum allocation size corresponding the desired extent size if the inode belongs to the data relocation tree, otherwise pass it the filesystem's sector size as the minimum allocation size. CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 91d6a46 ] gpi_ch_init() doesn't lock the ctrl_lock mutex, so there is no need to unlock it too. Instead the mutex is handled by the function gpi_alloc_chan_resources(), which properly locks and unlocks the mutex. ===================================== WARNING: bad unlock balance detected! 6.3.0-rc5-00253-g99792582ded1-dirty STMicroelectronics#15 Not tainted ------------------------------------- kworker/u16:0/9 is trying to release lock (&gpii->ctrl_lock) at: [<ffffb99d04e1284c>] gpi_alloc_chan_resources+0x108/0x5bc but there are no more locks to release! other info that might help us debug this: 6 locks held by kworker/u16:0/9: #0: ffff575740010938 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x220/0x594 STMicroelectronics#1: ffff80000809bdd0 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x220/0x594 STMicroelectronics#2: ffff575740f2a0f8 (&dev->mutex){....}-{3:3}, at: __device_attach+0x38/0x188 STMicroelectronics#3: ffff57574b5570f8 (&dev->mutex){....}-{3:3}, at: __device_attach+0x38/0x188 STMicroelectronics#4: ffffb99d06a2f180 (of_dma_lock){+.+.}-{3:3}, at: of_dma_request_slave_channel+0x138/0x280 STMicroelectronics#5: ffffb99d06a2ee20 (dma_list_mutex){+.+.}-{3:3}, at: dma_get_slave_channel+0x28/0x10c stack backtrace: CPU: 7 PID: 9 Comm: kworker/u16:0 Not tainted 6.3.0-rc5-00253-g99792582ded1-dirty STMicroelectronics#15 Hardware name: Google Pixel 3 (DT) Workqueue: events_unbound deferred_probe_work_func Call trace: dump_backtrace+0xa0/0xfc show_stack+0x18/0x24 dump_stack_lvl+0x60/0xac dump_stack+0x18/0x24 print_unlock_imbalance_bug+0x130/0x148 lock_release+0x270/0x300 __mutex_unlock_slowpath+0x48/0x2cc mutex_unlock+0x20/0x2c gpi_alloc_chan_resources+0x108/0x5bc dma_chan_get+0x84/0x188 dma_get_slave_channel+0x5c/0x10c gpi_of_dma_xlate+0x110/0x1a0 of_dma_request_slave_channel+0x174/0x280 dma_request_chan+0x3c/0x2d4 geni_i2c_probe+0x544/0x63c platform_probe+0x68/0xc4 really_probe+0x148/0x2ac __driver_probe_device+0x78/0xe0 driver_probe_device+0x3c/0x160 __device_attach_driver+0xb8/0x138 bus_for_each_drv+0x84/0xe0 __device_attach+0x9c/0x188 device_initial_probe+0x14/0x20 bus_probe_device+0xac/0xb0 device_add+0x60c/0x7d8 of_device_add+0x44/0x60 of_platform_device_create_pdata+0x90/0x124 of_platform_bus_create+0x15c/0x3c8 of_platform_populate+0x58/0xf8 devm_of_platform_populate+0x58/0xbc geni_se_probe+0xf0/0x164 platform_probe+0x68/0xc4 really_probe+0x148/0x2ac __driver_probe_device+0x78/0xe0 driver_probe_device+0x3c/0x160 __device_attach_driver+0xb8/0x138 bus_for_each_drv+0x84/0xe0 __device_attach+0x9c/0x188 device_initial_probe+0x14/0x20 bus_probe_device+0xac/0xb0 deferred_probe_work_func+0x8c/0xc8 process_one_work+0x2bc/0x594 worker_thread+0x228/0x438 kthread+0x108/0x10c ret_from_fork+0x10/0x20 Fixes: 5d0c353 ("dmaengine: qcom: Add GPI dma driver") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230409233355.453741-1-dmitry.baryshkov@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 05bb016 ] ACPICA commit 770653e3ba67c30a629ca7d12e352d83c2541b1e Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302 STMicroelectronics#1.2 0x000020d0f660777f in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x3d77f STMicroelectronics#1.1 0x000020d0f660777f in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x3d77f STMicroelectronics#1 0x000020d0f660777f in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:387 <libclang_rt.asan.so>+0x3d77f STMicroelectronics#2 0x000020d0f660b96d in handlepointer_overflow_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:809 <libclang_rt.asan.so>+0x4196d STMicroelectronics#3 0x000020d0f660b50d in compiler-rt/lib/ubsan/ubsan_handlers.cpp:815 <libclang_rt.asan.so>+0x4150d STMicroelectronics#4 0x000021e4213b3302 in acpi_ds_init_aml_walk(struct acpi_walk_state*, union acpi_parse_object*, struct acpi_namespace_node*, u8*, u32, struct acpi_evaluate_info*, u8) ../../third_party/acpica/source/components/dispatcher/dswstate.c:682 <platform-bus-x86.so>+0x233302 STMicroelectronics#5 0x000021e4213e2369 in acpi_ds_call_control_method(struct acpi_thread_state*, struct acpi_walk_state*, union acpi_parse_object*) ../../third_party/acpica/source/components/dispatcher/dsmethod.c:605 <platform-bus-x86.so>+0x262369 STMicroelectronics#6 0x000021e421437fac in acpi_ps_parse_aml(struct acpi_walk_state*) ../../third_party/acpica/source/components/parser/psparse.c:550 <platform-bus-x86.so>+0x2b7fac STMicroelectronics#7 0x000021e4214464d2 in acpi_ps_execute_method(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/parser/psxface.c:244 <platform-bus-x86.so>+0x2c64d2 STMicroelectronics#8 0x000021e4213aa052 in acpi_ns_evaluate(struct acpi_evaluate_info*) ../../third_party/acpica/source/components/namespace/nseval.c:250 <platform-bus-x86.so>+0x22a052 STMicroelectronics#9 0x000021e421413dd8 in acpi_ns_init_one_device(acpi_handle, u32, void*, void**) ../../third_party/acpica/source/components/namespace/nsinit.c:735 <platform-bus-x86.so>+0x293dd8 STMicroelectronics#10 0x000021e421429e98 in acpi_ns_walk_namespace(acpi_object_type, acpi_handle, u32, u32, acpi_walk_callback, acpi_walk_callback, void*, void**) ../../third_party/acpica/source/components/namespace/nswalk.c:298 <platform-bus-x86.so>+0x2a9e98 STMicroelectronics#11 0x000021e4214131ac in acpi_ns_initialize_devices(u32) ../../third_party/acpica/source/components/namespace/nsinit.c:268 <platform-bus-x86.so>+0x2931ac STMicroelectronics#12 0x000021e42147c40d in acpi_initialize_objects(u32) ../../third_party/acpica/source/components/utilities/utxfinit.c:304 <platform-bus-x86.so>+0x2fc40d STMicroelectronics#13 0x000021e42126d603 in acpi::acpi_impl::initialize_acpi(acpi::acpi_impl*) ../../src/devices/board/lib/acpi/acpi-impl.cc:224 <platform-bus-x86.so>+0xed603 Add a simple check that avoids incrementing a pointer by zero, but otherwise behaves as before. Note that our findings are against ACPICA 20221020, but the same code exists on master. Link: acpica/acpica@770653e3 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 63f8793 ] Make sure to check device queue mode in the null_validate_conf() and return error for NULL_Q_RQ as we don't allow legacy I/O path, without this patch we get OOPs when queue mode is set to 1 from configfs, following are repro steps :- modprobe null_blk nr_devices=0 mkdir config/nullb/nullb0 echo 1 > config/nullb/nullb0/memory_backed echo 4096 > config/nullb/nullb0/blocksize echo 20480 > config/nullb/nullb0/size echo 1 > config/nullb/nullb0/queue_mode echo 1 > config/nullb/nullb0/power Entering kdb (current=0xffff88810acdd080, pid 2372) on processor 42 Oops: (null) due to oops @ 0xffffffffc041c329 CPU: 42 PID: 2372 Comm: sh Tainted: G O N 6.3.0-rc5lblk+ STMicroelectronics#5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:null_add_dev.part.0+0xd9/0x720 [null_blk] Code: 01 00 00 85 d2 0f 85 a1 03 00 00 48 83 bb 08 01 00 00 00 0f 85 f7 03 00 00 80 bb 62 01 00 00 00 48 8b 75 20 0f 85 6d 02 00 00 <48> 89 6e 60 48 8b 75 20 bf 06 00 00 00 e8 f5 37 2c c1 48 8b 75 20 RSP: 0018:ffffc900052cbde0 EFLAGS: 00010246 RAX: 0000000000000001 RBX: ffff88811084d800 RCX: 0000000000000001 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888100042e00 RBP: ffff8881053d8200 R08: ffffc900052cbd68 R09: ffff888105db2000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000002 R13: ffff888104765200 R14: ffff88810eec1748 R15: ffff88810eec1740 FS: 00007fd445fd1740(0000) GS:ffff8897dfc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000060 CR3: 0000000166a00000 CR4: 0000000000350ee0 DR0: ffffffff8437a488 DR1: ffffffff8437a489 DR2: ffffffff8437a48a DR3: ffffffff8437a48b DR6: 00000000ffff0ff0 DR7: 0000000000000400 Call Trace: <TASK> nullb_device_power_store+0xd1/0x120 [null_blk] configfs_write_iter+0xb4/0x120 vfs_write+0x2ba/0x3c0 ksys_write+0x5f/0xe0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fd4460c57a7 Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 RSP: 002b:00007ffd3792a4a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd4460c57a7 RDX: 0000000000000002 RSI: 000055b43c02e4c0 RDI: 0000000000000001 RBP: 000055b43c02e4c0 R08: 000000000000000a R09: 00007fd44615b4e0 R10: 00007fd44615b3e0 R11: 0000000000000246 R12: 0000000000000002 R13: 00007fd446198520 R14: 0000000000000002 R15: 00007fd446198700 </TASK> Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com> Link: https://lore.kernel.org/r/20230416220339.43845-1-kch@nvidia.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 98bea25 ] Log load and replay is part of the metadata handle flow during mount operation. The $MFT record will be loaded and used while replaying logs. However, a malformed $MFT record, say, has RECORD_FLAG_DIR flag set and contains an ATTR_ROOT attribute will misguide kernel to treat it as a directory, and try to free the allocated resources when the corresponding inode is freed, which will cause an invalid kfree because the memory hasn't actually been allocated. [ 101.368647] BUG: KASAN: invalid-free in kvfree+0x2c/0x40 [ 101.369457] [ 101.369986] CPU: 0 PID: 198 Comm: mount Not tainted 6.0.0-rc7+ STMicroelectronics#5 [ 101.370529] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 101.371362] Call Trace: [ 101.371795] <TASK> [ 101.372157] dump_stack_lvl+0x49/0x63 [ 101.372658] print_report.cold+0xf5/0x689 [ 101.373022] ? ni_write_inode+0x754/0xd90 [ 101.373378] ? kvfree+0x2c/0x40 [ 101.373698] kasan_report_invalid_free+0x77/0xf0 [ 101.374058] ? kvfree+0x2c/0x40 [ 101.374352] ? kvfree+0x2c/0x40 [ 101.374668] __kasan_slab_free+0x189/0x1b0 [ 101.374992] ? kvfree+0x2c/0x40 [ 101.375271] kfree+0x168/0x3b0 [ 101.375717] kvfree+0x2c/0x40 [ 101.376002] indx_clear+0x26/0x60 [ 101.376316] ni_clear+0xc5/0x290 [ 101.376661] ntfs_evict_inode+0x45/0x70 [ 101.377001] evict+0x199/0x280 [ 101.377432] iput.part.0+0x286/0x320 [ 101.377819] iput+0x32/0x50 [ 101.378166] ntfs_loadlog_and_replay+0x143/0x320 [ 101.378656] ? ntfs_bio_fill_1+0x510/0x510 [ 101.378968] ? iput.part.0+0x286/0x320 [ 101.379367] ntfs_fill_super+0xecb/0x1ba0 [ 101.379729] ? put_ntfs+0x1d0/0x1d0 [ 101.380046] ? vsprintf+0x20/0x20 [ 101.380542] ? mutex_unlock+0x81/0xd0 [ 101.380914] ? set_blocksize+0x95/0x150 [ 101.381597] get_tree_bdev+0x232/0x370 [ 101.382254] ? put_ntfs+0x1d0/0x1d0 [ 101.382699] ntfs_fs_get_tree+0x15/0x20 [ 101.383094] vfs_get_tree+0x4c/0x130 [ 101.383675] path_mount+0x654/0xfe0 [ 101.384203] ? putname+0x80/0xa0 [ 101.384540] ? finish_automount+0x2e0/0x2e0 [ 101.384943] ? putname+0x80/0xa0 [ 101.385362] ? kmem_cache_free+0x1c4/0x440 [ 101.385968] ? putname+0x80/0xa0 [ 101.386666] do_mount+0xd6/0xf0 [ 101.387228] ? path_mount+0xfe0/0xfe0 [ 101.387585] ? __kasan_check_write+0x14/0x20 [ 101.387979] __x64_sys_mount+0xca/0x110 [ 101.388436] do_syscall_64+0x3b/0x90 [ 101.388757] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 101.389289] RIP: 0033:0x7fa0f70e948a [ 101.390048] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 101.391297] RSP: 002b:00007ffc24fdecc8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 [ 101.391988] RAX: ffffffffffffffda RBX: 000055932c183060 RCX: 00007fa0f70e948a [ 101.392494] RDX: 000055932c183260 RSI: 000055932c1832e0 RDI: 000055932c18bce0 [ 101.393053] RBP: 0000000000000000 R08: 000055932c183280 R09: 0000000000000020 [ 101.393577] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 000055932c18bce0 [ 101.394044] R13: 000055932c183260 R14: 0000000000000000 R15: 00000000ffffffff [ 101.394747] </TASK> [ 101.395402] [ 101.396047] Allocated by task 198: [ 101.396724] kasan_save_stack+0x26/0x50 [ 101.397400] __kasan_slab_alloc+0x6d/0x90 [ 101.397974] kmem_cache_alloc_lru+0x192/0x5a0 [ 101.398524] ntfs_alloc_inode+0x23/0x70 [ 101.399137] alloc_inode+0x3b/0xf0 [ 101.399534] iget5_locked+0x54/0xa0 [ 101.400026] ntfs_iget5+0xaf/0x1780 [ 101.400414] ntfs_loadlog_and_replay+0xe5/0x320 [ 101.400883] ntfs_fill_super+0xecb/0x1ba0 [ 101.401313] get_tree_bdev+0x232/0x370 [ 101.401774] ntfs_fs_get_tree+0x15/0x20 [ 101.402224] vfs_get_tree+0x4c/0x130 [ 101.402673] path_mount+0x654/0xfe0 [ 101.403160] do_mount+0xd6/0xf0 [ 101.403537] __x64_sys_mount+0xca/0x110 [ 101.404058] do_syscall_64+0x3b/0x90 [ 101.404333] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 101.404816] [ 101.405067] The buggy address belongs to the object at ffff888008cc9ea0 [ 101.405067] which belongs to the cache ntfs_inode_cache of size 992 [ 101.406171] The buggy address is located 232 bytes inside of [ 101.406171] 992-byte region [ffff888008cc9ea0, ffff888008cca280) [ 101.406995] [ 101.408559] The buggy address belongs to the physical page: [ 101.409320] page:00000000dccf19dd refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8cc8 [ 101.410654] head:00000000dccf19dd order:2 compound_mapcount:0 compound_pincount:0 [ 101.411533] flags: 0xfffffc0010200(slab|head|node=0|zone=1|lastcpupid=0x1fffff) [ 101.412665] raw: 000fffffc0010200 0000000000000000 dead000000000122 ffff888003695140 [ 101.413209] raw: 0000000000000000 00000000800e000e 00000001ffffffff 0000000000000000 [ 101.413799] page dumped because: kasan: bad access detected [ 101.414213] [ 101.414427] Memory state around the buggy address: [ 101.414991] ffff888008cc9e80: fc fc fc fc 00 00 00 00 00 00 00 00 00 00 00 00 [ 101.415785] ffff888008cc9f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 101.416933] >ffff888008cc9f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 101.417857] ^ [ 101.418566] ffff888008cca000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 101.419704] ffff888008cca080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Signed-off-by: Edward Lo <edward.lo@ambergroup.io> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bdc1c5f ] In binder_transaction_buffer_release() the 'failed_at' offset indicates the number of objects to clean up. However, this function was changed by commit 44d8047 ("binder: use standard functions to allocate fds"), to release all the objects in the buffer when 'failed_at' is zero. This introduced an issue when a transaction buffer is released without any objects having been processed so far. In this case, 'failed_at' is indeed zero yet it is misinterpreted as releasing the entire buffer. This leads to use-after-free errors where nodes are incorrectly freed and subsequently accessed. Such is the case in the following KASAN report: ================================================================== BUG: KASAN: slab-use-after-free in binder_thread_read+0xc40/0x1f30 Read of size 8 at addr ffff4faf037cfc58 by task poc/474 CPU: 6 PID: 474 Comm: poc Not tainted 6.3.0-12570-g7df047b3f0aa STMicroelectronics#5 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0x94/0xec show_stack+0x18/0x24 dump_stack_lvl+0x48/0x60 print_report+0xf8/0x5b8 kasan_report+0xb8/0xfc __asan_load8+0x9c/0xb8 binder_thread_read+0xc40/0x1f30 binder_ioctl+0xd9c/0x1768 __arm64_sys_ioctl+0xd4/0x118 invoke_syscall+0x60/0x188 [...] Allocated by task 474: kasan_save_stack+0x3c/0x64 kasan_set_track+0x2c/0x40 kasan_save_alloc_info+0x24/0x34 __kasan_kmalloc+0xb8/0xbc kmalloc_trace+0x48/0x5c binder_new_node+0x3c/0x3a4 binder_transaction+0x2b58/0x36f0 binder_thread_write+0x8e0/0x1b78 binder_ioctl+0x14a0/0x1768 __arm64_sys_ioctl+0xd4/0x118 invoke_syscall+0x60/0x188 [...] Freed by task 475: kasan_save_stack+0x3c/0x64 kasan_set_track+0x2c/0x40 kasan_save_free_info+0x38/0x5c __kasan_slab_free+0xe8/0x154 __kmem_cache_free+0x128/0x2bc kfree+0x58/0x70 binder_dec_node_tmpref+0x178/0x1fc binder_transaction_buffer_release+0x430/0x628 binder_transaction+0x1954/0x36f0 binder_thread_write+0x8e0/0x1b78 binder_ioctl+0x14a0/0x1768 __arm64_sys_ioctl+0xd4/0x118 invoke_syscall+0x60/0x188 [...] ================================================================== In order to avoid these issues, let's always calculate the intended 'failed_at' offset beforehand. This is renamed and wrapped in a helper function to make it clear and convenient. Fixes: 32e9f56 ("binder: don't detect sender/target during buffer cleanup") Reported-by: Zi Fan Tan <zifantan@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20230505203020.4101154-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

Hou Tao says: ==================== The patch set fixes several issues in bits iterator. Patch STMicroelectronics#1 fixes the kmemleak problem of bits iterator. Patch STMicroelectronics#2~STMicroelectronics#3 fix the overflow problem of nr_bits. Patch STMicroelectronics#4 fixes the potential stack corruption when bits iterator is used on 32-bit host. Patch STMicroelectronics#5 adds more test cases for bits iterator. Please see the individual patches for more details. And comments are always welcome. --- v4: * patch STMicroelectronics#1: add ack from Yafang * patch STMicroelectronics#3: revert code-churn like changes: (1) compute nr_bytes and nr_bits before the check of nr_words. (2) use nr_bits == 64 to check for single u64, preventing build warning on 32-bit hosts. * patch STMicroelectronics#4: use "BITS_PER_LONG == 32" instead of "!defined(CONFIG_64BIT)" v3: https://lore.kernel.org/bpf/20241025013233.804027-1-houtao@huaweicloud.com/T/#t * split the bits-iterator related patches from "Misc fixes for bpf" patch set * patch STMicroelectronics#1: use "!nr_bits || bits >= nr_bits" to stop the iteration * patch STMicroelectronics#2: add a new helper for the overflow problem * patch STMicroelectronics#3: decrease the limitation from 512 to 511 and check whether nr_bytes is too large for bpf memory allocator explicitly * patch STMicroelectronics#5: add two more test cases for bit iterator v2: http://lore.kernel.org/bpf/d49fa2f4-f743-c763-7579-c3cab4dd88cb@huaweicloud.com ==================== Link: https://lore.kernel.org/r/20241030100516.3633640-1-houtao@huaweicloud.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Petr Machata says: ==================== mlxsw: Fixes In this patchset: - Tx header should be pushed for each packet which is transmitted via Spectrum ASICs. Patch STMicroelectronics#1 adds a missing call to skb_cow_head() to make sure that there is both enough room to push the Tx header and that the SKB header is not cloned and can be modified. - Commit b5b60bb ("mlxsw: pci: Use page pool for Rx buffers allocation") converted mlxsw to use page pool for Rx buffers allocation. Sync for CPU and for device should be done for Rx pages. In patches STMicroelectronics#2 and STMicroelectronics#3, add the missing calls to sync pages for, respectively, CPU and the device. - Patch STMicroelectronics#4 then fixes a bug to IPv6 GRE forwarding offload. Patch STMicroelectronics#5 adds a generic forwarding test that fails with mlxsw ports prior to the fix. ==================== Link: https://patch.msgid.link/cover.1729866134.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Disable strict aliasing, as has been done in the kernel proper for decades (literally since before git history) to fix issues where gcc will optimize away loads in code that looks 100% correct, but is _technically_ undefined behavior, and thus can be thrown away by the compiler. E.g. arm64's vPMU counter access test casts a uint64_t (unsigned long) pointer to a u64 (unsigned long long) pointer when setting PMCR.N via u64p_replace_bits(), which gcc-13 detects and optimizes away, i.e. ignores the result and uses the original PMCR. The issue is most easily observed by making set_pmcr_n() noinline and wrapping the call with printf(), e.g. sans comments, for this code: printf("orig = %lx, next = %lx, want = %lu\n", pmcr_orig, pmcr, pmcr_n); set_pmcr_n(&pmcr, pmcr_n); printf("orig = %lx, next = %lx, want = %lu\n", pmcr_orig, pmcr, pmcr_n); gcc-13 generates: 0000000000401c90 <set_pmcr_n>: 401c90: f9400002 ldr x2, [x0] 401c94: b3751022 bfi x2, x1, STMicroelectronics#11, STMicroelectronics#5 401c98: f9000002 str x2, [x0] 401c9c: d65f03c0 ret 0000000000402660 <test_create_vpmu_vm_with_pmcr_n>: 402724: aa1403e3 mov x3, x20 402728: aa1503e2 mov x2, x21 40272c: aa1603e0 mov x0, x22 402730: aa1503e1 mov x1, x21 402734: 940060ff bl 41ab30 <_IO_printf> 402738: aa1403e1 mov x1, x20 40273c: 910183e0 add x0, sp, #0x60 402740: 97fffd54 bl 401c90 <set_pmcr_n> 402744: aa1403e3 mov x3, x20 402748: aa1503e2 mov x2, x21 40274c: aa1503e1 mov x1, x21 402750: aa1603e0 mov x0, x22 402754: 940060f7 bl 41ab30 <_IO_printf> with the value stored in [sp + 0x60] ignored by both printf() above and in the test proper, resulting in a false failure due to vcpu_set_reg() simply storing the original value, not the intended value. $ ./vpmu_counter_access Random seed: 0x6b8b4567 orig = 3040, next = 3040, want = 0 orig = 3040, next = 3040, want = 0 ==== Test Assertion Failure ==== aarch64/vpmu_counter_access.c:505: pmcr_n == get_pmcr_n(pmcr) pid=71578 tid=71578 errno=9 - Bad file descriptor 1 0x400673: run_access_test at vpmu_counter_access.c:522 2 (inlined by) main at vpmu_counter_access.c:643 3 0x4132d7: __libc_start_call_main at libc-start.o:0 4 0x413653: __libc_start_main at ??:0 5 0x40106f: _start at ??:0 Failed to update PMCR.N to 0 (received: 6) Somewhat bizarrely, gcc-11 also exhibits the same behavior, but only if set_pmcr_n() is marked noinline, whereas gcc-13 fails even if set_pmcr_n() is inlined in its sole caller. Cc: stable@vger.kernel.org Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=116912 Signed-off-by: Sean Christopherson <seanjc@google.com>

Blackrose added 30 commits June 22, 2019 01:15

dts: pangu: Add PanGu board from i2SOM

5dd76a0

The PanGu board use STM32MP157 SoC, and support more functions. Such as HDMI, ethernet, USB host, USB OTG, LCD, MIPI, Camera etc..

dts: pangu: PanGu board only one QSPI flash

170d155

removed the unused flash section

dts: pangu: move camera to i2c5

ff1fafe

Move camera(ov5640) into i2c5 section. Fix the clock pinmux of i2s2.

dts: panguboard: disable HDMI when LCD using

d2d1303

1. disable HDMI when LCD is using 2. fix the IRQ line of ft5316 chip conflict with same number, so switch the IRQ and reset line 3. The DCMI using 8bit data line

dts: panguboard: move ft5x06 section to lcd file

fa4d374

config: panguboard: enable TSC2007 touch chip

b267941

dts: panguboard: disable the TSC2007 touch chip

59ba0fc

dts: panguboard: add support more LCD and touch panel

b11249b

support LCDs size are 4.3inch and 7inch. support touch IC is GT9147.

pinctrl: stm32: remove the strict flag

82388b5

The stm32mp1 can not configre a pin with pinctrl and gpio framework at same time. We need disable it to configure the irq pin of gt9147 use pull-down setting.

driver:usb support Quectel EC20 LTE module

5419316

The host use QMI method to communicate with LTE module.

config:panguboard: enable 4G LTE module config

9f4a734

arm:dts: support LCD modules

ef13b6f

i2M-LCD043P800C i2M-LCD070P1024C

arm:dts: fix panguboard mipi use wrong node id

440c9a8

arm:dts: add i2C-MP15X-B nand and emmc variant

cc9cf59

NAND variant stm32mp157a-i2cmp15xbn.dts eMMC variant stm32mp157a-i2cmp15xbe.dts

arm:dts:i2som: add lcd070 for i2cmp15xb board

8d52028

arm:configs: enable more features

0e77c2e

enable gpio watchdog enalbe load HDMI EDID firmware enable USB HID devices

arm:dts: fix wrong include dts file

c3652d5

arm:config enable more function driver

c4a2289

usb serial driver usb rndis driver

usb:serial add YUGA CLM920 AC3 4G module

a677e3e

sound:codecs: add depend config for wm8904

1775619

sound:generic: use sysclk for wm8904

a2dfcf2

arm:dts: configure periphery for i2C-MP15X-B board

82a3041

arm:dts add i2M-GiantAxe board with PanGu Board

9ffcccb

The i2M-GiantAxe board is a extension board for PanGu board. It's adds 4G LTE slot, WiFi & BT module, RS232, RS485, CAN, I2C, SPI and TIM1 signal.

arm:dts: add dts for i2M-GiantAxe board

b170efd

arm:configs: enable some kernel driver

cd86c75

The i2C-MP15X-B board has wm8904 and ksz9301 chip.

arm:dts: add property for sdmmc3

ed7600b

arm:dts: add i2M-GiantAxe module with different modes

7ef93b8

tty:serial: add rs485 txen-gpio

67625ba

arm:dts adjust value for KSZ9031

aa9b43e

ST-dot-com closed this May 28, 2020

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

V4.19 r1.4 pangu #5

V4.19 r1.4 pangu #5

jyorin commented May 28, 2020

ST-dot-com commented May 28, 2020

V4.19 r1.4 pangu #5

V4.19 r1.4 pangu #5

Conversation

jyorin commented May 28, 2020

ST-dot-com commented May 28, 2020