dmaengine: pl330: _prep_dma_memcpy: Fix wrong burst size

Actually, burst size is equal to '1 << desc->rqcfg.brst_size'.
we should use burst size, not desc->rqcfg.brst_size.

dma memcpy performance on Rockchip RV1126
@ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA:

dmatest:

/# echo dma0chan0 > /sys/module/dmatest/parameters/channel
/# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size
/# echo 8 > /sys/module/dmatest/parameters/iterations
/# echo y > /sys/module/dmatest/parameters/norandom
/# echo y > /sys/module/dmatest/parameters/verbose
/# echo 1 > /sys/module/dmatest/parameters/run

dmatest: dma0chan0-copy0: result andy-shev#1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result andy-shev#8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000

Before:

  dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0)

After this patch:

  dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0)

After this patch and increase dma clk to 400MHz:

  dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0)

Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Link: https://lore.kernel.org/r/1605326106-55681-1-git-send-email-sugar.zhang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

drivers/dma/pl330.c

@@ -2799,7 +2799,7 @@ pl330_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dst,
 	 * If burst size is smaller than bus width then make sure we only
 	 * transfer one at a time to avoid a burst stradling an MFIFO entry.
 	 */
-	if (desc->rqcfg.brst_size * 8 < pl330->pcfg.data_bus_width)
+	if (burst * 8 < pl330->pcfg.data_bus_width)
 		desc->rqcfg.brst_len = 1;
 
 	desc->bytes_requested = len;