Merge branch 'gianfar-next'

Claudiu Manoil says:

====================
gianfar: Tx timeout issue

There's an older Tx timeout issue showing up on etsec2 devices
with 2 CPUs.  I pinned this issue down to processing overhead
incurred by supporting multiple Tx/Rx rings, as explained in
the 2nd patch below.  But before this, there's also a concurency
issue leading to Rx/Tx spurrious interrupts, addressed by the
'Tx NAPI' patch below.
The Tx timeout can be triggered with multiple Tx flows,
'iperf -c -N 8' commands, on a 2 CPUs etsec2 based (P1020) board.

Before the patches:
"""
root@p1020rdb-pc:~# iperf -c 172.16.1.3 -n 1000M -P 8 &
[...]
root@p1020rdb-pc:~# NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue 1 timed out
WARNING: at net/sched/sch_generic.c:279
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.13.0-rc3-03386-g89ea59c #23
task: ed84ef40 ti: ed868000 task.ti: ed868000
NIP: c04627a8 LR: c04627a8 CTR: c02fb270
REGS: ed869d00 TRAP: 0700   Not tainted  (3.13.0-rc3-03386-g89ea59c)
MSR: 00029000 <CE,EE,ME>  CR: 44000022  XER: 20000000
[...]

root@p1020rdb-pc:~# [ ID] Interval       Transfer     Bandwidth
[  5]  0.0-19.3 sec  1000 MBytes    434 Mbits/sec
[  8]  0.0-39.7 sec  1000 MBytes    211 Mbits/sec
[  9]  0.0-40.1 sec  1000 MBytes    209 Mbits/sec
[  3]  0.0-40.2 sec  1000 MBytes    209 Mbits/sec
[ 10]  0.0-59.0 sec  1000 MBytes    142 Mbits/sec
[  7]  0.0-74.6 sec  1000 MBytes    112 Mbits/sec
[  6]  0.0-74.7 sec  1000 MBytes    112 Mbits/sec
[  4]  0.0-74.7 sec  1000 MBytes    112 Mbits/sec
[SUM]  0.0-74.7 sec  7.81 GBytes    898 Mbits/sec

root@p1020rdb-pc:~# ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:04:9f:00:13:01
          inet addr:172.16.1.1  Bcast:172.16.255.255  Mask:255.255.0.0
          inet6 addr: fe80::204:9fff:fe00:1301/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:708722 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8717849 errors:6 dropped:0 overruns:1470 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:58118018 (55.4 MiB)  TX bytes:274069482 (261.3 MiB)
          Base address:0xa000

"""

After applying the patches:
"""
root@p1020rdb-pc:~# iperf -c 172.16.1.3 -n 1000M -P 8 &
[...]
root@p1020rdb-pc:~# [ ID] Interval       Transfer     Bandwidth
[  9]  0.0-70.5 sec  1000 MBytes    119 Mbits/sec
[  5]  0.0-70.5 sec  1000 MBytes    119 Mbits/sec
[  6]  0.0-70.7 sec  1000 MBytes    119 Mbits/sec
[  4]  0.0-71.0 sec  1000 MBytes    118 Mbits/sec
[  8]  0.0-71.1 sec  1000 MBytes    118 Mbits/sec
[  3]  0.0-71.2 sec  1000 MBytes    118 Mbits/sec
[ 10]  0.0-71.3 sec  1000 MBytes    118 Mbits/sec
[  7]  0.0-71.3 sec  1000 MBytes    118 Mbits/sec
[SUM]  0.0-71.3 sec  7.81 GBytes    942 Mbits/sec

root@p1020rdb-pc:~# ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:04:9f:00:13:01
          inet addr:172.16.1.1  Bcast:172.16.255.255  Mask:255.255.0.0
          inet6 addr: fe80::204:9fff:fe00:1301/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:728446 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8690057 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:59732650 (56.9 MiB)  TX bytes:271554306 (258.9 MiB)
          Base address:0xa000
"""
v2: PATCH 2:
    Replaced CPP check with run-time condition to
    limit the number of queues. Updated comments.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>