merge from thesofproject #1

bardliao · 2018-09-17T08:58:18Z

No description provided.

This patch adds the handling of snd_soc_dapm_effect that was missing. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

This patch updates the maximum size into the same as used currently in DSP side. Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

This patch updates the definitions and structs to indentical as used on DSP side. It will help using the equalizer setup blobs in user space. Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

This patch adds the binary control into topology parsing and provides for ASoC the SOF ext bytes put and get functions. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

Remove a stray character and add a missing header. The GPIO IRQ is requested as a managed resource during probing, therefore there's no need to explicitly release it during driver unbinding. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

Checking for the IRQ GPIO level once an IRQ has been triggered shouldn't be necessary, once an IRQ has been triggered, so this might end up being superfluous. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

The SOF DT doesn't compile yet, it's only provided as an example, disable it for now to prevent automated builds from failing. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

This reverts commit 41b8f5d and fixes #113. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

The snd_sgbuf_aligned_pages() inline function is currently only defined if CONFIG_SND_DMA_SGBUF is enabled. This isn't needed, the function doesn't need SG DMA to be valid. Move it outside of #ifdef. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

oops case: the snd_card{} would be freed ahead of dynamic kcontrol remove process, in this process, the snd_card{} will be used, then the oops will be hit. the solution: the operation of removing the dynamic kcontrol should be ahead of snd_card{} free. Signed-off-by: Wu Zhigang <zhigang.wu@linux.intel.com>

remove the dynamic object during the topology free stage. to avoid multi remove operation. Signed-off-by: Wu Zhigang <zhigang.wu@linux.intel.com>

This patch adds support for retreiving byte control data after the DSP comes out of D3. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

If use IPC poistion update, read position from IPC position. For Playback, Use DPIB register from HDA space which reflects the actual data transferred. For Capture, Use the position buffer for pointer, as DPIB is not accurate enough, its update may be completed earlier than the data written to DDR. Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

Which will make it possible to retrieve stream_tag and change host_period_bytes in for HDA hs_params(), the latter will make disable position update IPC for HDA stream possbile. Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

In DPIB/posbuf position pointer mode, we don't have position update IPC messages, we may need(depends on if no_irq is set) set different IOC flags for each BDL entry. Without IOC setting for BDL entries, irq mode won't work as there is no interrupt happens at each period finished. Last, we set BDL IOC at DPIB/pos mode only. Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

pcm_runtime is not ready yet at hw_params() stage, so we need to retrieve period settings from params here. Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>

Remove no_pcm check to invoke pcm_new() for backend dai-links too. This fixes crash in hdmi codec driver during hdmi_codec_startup() while accessing chmap_info struct. chmap_info struct memory is allocated in pcm_new() of hdmi codec driver which is not invoked in case of DPCM when hdmi codec driver is part of backend dai-link. Below is the crash stack: [ 61.635493] Unable to handle kernel NULL pointer dereference at virtual address 00000018 .. [ 61.666696] CM = 0, WnR = 1 [ 61.669778] user pgtable: 4k pages, 39-bit VAs, pgd = ffffffc0d6633000 [ 61.676526] [0000000000000018] *pgd=0000000153fc8003, *pud=0000000153fc8003, *pmd=0000000000000000 [ 61.685793] Internal error: Oops: 96000046 [#1] PREEMPT SMP [ 61.722955] CPU: 7 PID: 2238 Comm: aplay Not tainted 4.14.72 thesofproject#21 .. [ 61.740269] PC is at hdmi_codec_startup+0x124/0x164 [ 61.745308] LR is at hdmi_codec_startup+0xe4/0x164 Signed-off-by: Rohit kumar <rohitkr@codeaurora.org> Signed-off-by: Mark Brown <broonie@kernel.org> (cherry picked from commit de17f14)

We can concurrently try to open the same sub-channel from 2 paths: path #1: vmbus_onoffer() -> vmbus_process_offer() -> handle_sc_creation(). path #2: storvsc_probe() -> storvsc_connect_to_vsp() -> -> storvsc_channel_init() -> handle_multichannel_storage() -> -> vmbus_are_subchannels_present() -> handle_sc_creation(). They conflict with each other, but it was not an issue before the recent commit ae6935e ("vmbus: split ring buffer allocation from open"), because at the beginning of vmbus_open() we checked newchannel->state so only one path could succeed, and the other would return with -EINVAL. After ae6935e, the failing path frees the channel's ringbuffer by vmbus_free_ring(), and this causes a panic later. Commit ae6935e itself is good, and it just reveals the longstanding race. We can resolve the issue by removing path #2, i.e. removing the second vmbus_are_subchannels_present() in handle_multichannel_storage(). BTW, the comment "Check to see if sub-channels have already been created" in handle_multichannel_storage() is incorrect: when we unload the driver, we first close the sub-channel(s) and then close the primary channel, next the host sends rescind-offer message(s) so primary->sc_list will become empty. This means the first vmbus_are_subchannels_present() in handle_multichannel_storage() is never useful. Fixes: ae6935e ("vmbus: split ring buffer allocation from open") Cc: stable@vger.kernel.org Cc: Long Li <longli@microsoft.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

__qdisc_drop_all() accesses skb->prev to get to the tail of the segment-list. With commit 68d2f84 ("net: gro: properly remove skb from list") the skb-list handling has been changed to set skb->next to NULL and set the list-poison on skb->prev. With that change, __qdisc_drop_all() will panic when it tries to dereference skb->prev. Since commit 992cba7 ("net: Add and use skb_list_del_init().") __list_del_entry is used, leaving skb->prev unchanged (thus, pointing to the list-head if it's the first skb of the list). This will make __qdisc_drop_all modify the next-pointer of the list-head and result in a panic later on: [ 34.501053] general protection fault: 0000 [#1] SMP KASAN PTI [ 34.501968] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.20.0-rc2.mptcp thesofproject#108 [ 34.502887] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 [ 34.504074] RIP: 0010:dev_gro_receive+0x343/0x1f90 [ 34.504751] Code: e0 48 c1 e8 03 42 80 3c 30 00 0f 85 4a 1c 00 00 4d 8b 24 24 4c 39 65 d0 0f 84 0a 04 00 00 49 8d 7c 24 38 48 89 f8 48 c1 e8 03 <42> 0f b6 04 30 84 c0 74 08 3c 04 [ 34.507060] RSP: 0018:ffff8883af507930 EFLAGS: 00010202 [ 34.507761] RAX: 0000000000000007 RBX: ffff8883970b2c80 RCX: 1ffff11072e165a6 [ 34.508640] RDX: 1ffff11075867008 RSI: ffff8883ac338040 RDI: 0000000000000038 [ 34.509493] RBP: ffff8883af5079d0 R08: ffff8883970b2d40 R09: 0000000000000062 [ 34.510346] R10: 0000000000000034 R11: 0000000000000000 R12: 0000000000000000 [ 34.511215] R13: 0000000000000000 R14: dffffc0000000000 R15: ffff8883ac338008 [ 34.512082] FS: 0000000000000000(0000) GS:ffff8883af500000(0000) knlGS:0000000000000000 [ 34.513036] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 34.513741] CR2: 000055ccc3e9d020 CR3: 00000003abf32000 CR4: 00000000000006e0 [ 34.514593] Call Trace: [ 34.514893] <IRQ> [ 34.515157] napi_gro_receive+0x93/0x150 [ 34.515632] receive_buf+0x893/0x3700 [ 34.516094] ? __netif_receive_skb+0x1f/0x1a0 [ 34.516629] ? virtnet_probe+0x1b40/0x1b40 [ 34.517153] ? __stable_node_chain+0x4d0/0x850 [ 34.517684] ? kfree+0x9a/0x180 [ 34.518067] ? __kasan_slab_free+0x171/0x190 [ 34.518582] ? detach_buf+0x1df/0x650 [ 34.519061] ? lapic_next_event+0x5a/0x90 [ 34.519539] ? virtqueue_get_buf_ctx+0x280/0x7f0 [ 34.520093] virtnet_poll+0x2df/0xd60 [ 34.520533] ? receive_buf+0x3700/0x3700 [ 34.521027] ? qdisc_watchdog_schedule_ns+0xd5/0x140 [ 34.521631] ? htb_dequeue+0x1817/0x25f0 [ 34.522107] ? sch_direct_xmit+0x142/0xf30 [ 34.522595] ? virtqueue_napi_schedule+0x26/0x30 [ 34.523155] net_rx_action+0x2f6/0xc50 [ 34.523601] ? napi_complete_done+0x2f0/0x2f0 [ 34.524126] ? kasan_check_read+0x11/0x20 [ 34.524608] ? _raw_spin_lock+0x7d/0xd0 [ 34.525070] ? _raw_spin_lock_bh+0xd0/0xd0 [ 34.525563] ? kvm_guest_apic_eoi_write+0x6b/0x80 [ 34.526130] ? apic_ack_irq+0x9e/0xe0 [ 34.526567] __do_softirq+0x188/0x4b5 [ 34.527015] irq_exit+0x151/0x180 [ 34.527417] do_IRQ+0xdb/0x150 [ 34.527783] common_interrupt+0xf/0xf [ 34.528223] </IRQ> This patch makes sure that skb->prev is set to NULL when entering netem_enqueue. Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp> Cc: Tyler Hicks <tyhicks@canonical.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Fixes: 68d2f84 ("net: gro: properly remove skb from list") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>

It was observed that a process blocked indefintely in __fscache_read_or_alloc_page(), waiting for FSCACHE_COOKIE_LOOKING_UP to be cleared via fscache_wait_for_deferred_lookup(). At this time, ->backing_objects was empty, which would normaly prevent __fscache_read_or_alloc_page() from getting to the point of waiting. This implies that ->backing_objects was cleared *after* __fscache_read_or_alloc_page was was entered. When an object is "killed" and then "dropped", FSCACHE_COOKIE_LOOKING_UP is cleared in fscache_lookup_failure(), then KILL_OBJECT and DROP_OBJECT are "called" and only in DROP_OBJECT is ->backing_objects cleared. This leaves a window where something else can set FSCACHE_COOKIE_LOOKING_UP and __fscache_read_or_alloc_page() can start waiting, before ->backing_objects is cleared There is some uncertainty in this analysis, but it seems to be fit the observations. Adding the wake in this patch will be handled correctly by __fscache_read_or_alloc_page(), as it checks if ->backing_objects is empty again, after waiting. Customer which reported the hang, also report that the hang cannot be reproduced with this fix. The backtrace for the blocked process looked like: PID: 29360 TASK: ffff881ff2ac0f80 CPU: 3 COMMAND: "zsh" #0 [ffff881ff43efbf8] schedule at ffffffff815e56f1 #1 [ffff881ff43efc58] bit_wait at ffffffff815e64ed #2 [ffff881ff43efc68] __wait_on_bit at ffffffff815e61b8 #3 [ffff881ff43efca0] out_of_line_wait_on_bit at ffffffff815e625e #4 [ffff881ff43efd08] fscache_wait_for_deferred_lookup at ffffffffa04f2e8f [fscache] thesofproject#5 [ffff881ff43efd18] __fscache_read_or_alloc_page at ffffffffa04f2ffe [fscache] thesofproject#6 [ffff881ff43efd58] __nfs_readpage_from_fscache at ffffffffa0679668 [nfs] thesofproject#7 [ffff881ff43efd78] nfs_readpage at ffffffffa067092b [nfs] thesofproject#8 [ffff881ff43efda0] generic_file_read_iter at ffffffff81187a73 thesofproject#9 [ffff881ff43efe50] nfs_file_read at ffffffffa066544b [nfs] thesofproject#10 [ffff881ff43efe70] __vfs_read at ffffffff811fc756 thesofproject#11 [ffff881ff43efee8] vfs_read at ffffffff811fccfa thesofproject#12 [ffff881ff43eff18] sys_read at ffffffff811fda62 thesofproject#13 [ffff881ff43eff50] entry_SYSCALL_64_fastpath at ffffffff815e986e Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: David Howells <dhowells@redhat.com>

There are actually two kinds of discard merge: - one is the normal discard merge, just like normal read/write request, and call it single-range discard - another is the multi-range discard, queue_max_discard_segments(rq->q) > 1 For the former case, queue_max_discard_segments(rq->q) is 1, and we should handle this kind of discard merge like the normal read/write request. This patch fixes the following kernel panic issue[1], which is caused by not removing the single-range discard request from elevator queue. Guangwu has one raid discard test case, in which this issue is a bit easier to trigger, and I verified that this patch can fix the kernel panic issue in Guangwu's test case. [1] kernel panic log from Jens's report BUG: unable to handle kernel NULL pointer dereference at 0000000000000148 PGD 0 P4D 0. Oops: 0000 [#1] SMP PTI CPU: 37 PID: 763 Comm: kworker/37:1H Not tainted \ 4.20.0-rc3-00649-ge64d9a554a91-dirty thesofproject#14 Hardware name: Wiwynn \ Leopard-Orv2/Leopard-DDR BW, BIOS LBM08 03/03/2017 Workqueue: kblockd \ blk_mq_run_work_fn RIP: \ 0010:blk_mq_get_driver_tag+0x81/0x120 Code: 24 \ 10 48 89 7c 24 20 74 21 83 fa ff 0f 95 c0 48 8b 4c 24 28 65 48 33 0c 25 28 00 00 00 \ 0f 85 96 00 00 00 48 83 c4 30 5b 5d c3 <48> 8b 87 48 01 00 00 8b 40 04 39 43 20 72 37 \ f6 87 b0 00 00 00 02 RSP: 0018:ffffc90004aabd30 EFLAGS: 00010246 \ RAX: 0000000000000003 RBX: ffff888465ea1300 RCX: ffffc90004aabde8 RDX: 00000000ffffffff RSI: ffffc90004aabde8 RDI: 0000000000000000 RBP: 0000000000000000 R08: ffff888465ea1348 R09: 0000000000000000 R10: 0000000000001000 R11: 00000000ffffffff R12: ffff888465ea1300 R13: 0000000000000000 R14: ffff888465ea1348 R15: ffff888465d10000 FS: 0000000000000000(0000) GS:ffff88846f9c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000148 CR3: 000000000220a003 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: blk_mq_dispatch_rq_list+0xec/0x480 ? elv_rb_del+0x11/0x30 blk_mq_do_dispatch_sched+0x6e/0xf0 blk_mq_sched_dispatch_requests+0xfa/0x170 __blk_mq_run_hw_queue+0x5f/0xe0 process_one_work+0x154/0x350 worker_thread+0x46/0x3c0 kthread+0xf5/0x130 ? process_one_work+0x350/0x350 ? kthread_destroy_worker+0x50/0x50 ret_from_fork+0x1f/0x30 Modules linked in: sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel \ kvm switchtec irqbypass iTCO_wdt iTCO_vendor_support efivars cdc_ether usbnet mii \ cdc_acm i2c_i801 lpc_ich mfd_core ipmi_si ipmi_devintf ipmi_msghandler acpi_cpufreq \ button sch_fq_codel nfsd nfs_acl lockd grace auth_rpcgss oid_registry sunrpc nvme \ nvme_core fuse sg loop efivarfs autofs4 CR2: 0000000000000148 \ ---[ end trace 340a1fb996df1b9b ]--- RIP: 0010:blk_mq_get_driver_tag+0x81/0x120 Code: 24 10 48 89 7c 24 20 74 21 83 fa ff 0f 95 c0 48 8b 4c 24 28 65 48 33 0c 25 28 \ 00 00 00 0f 85 96 00 00 00 48 83 c4 30 5b 5d c3 <48> 8b 87 48 01 00 00 8b 40 04 39 43 \ 20 72 37 f6 87 b0 00 00 00 02 Fixes: 445251d ("blk-mq: fix discard merge with scheduler attached") Reported-by: Jens Axboe <axboe@kernel.dk> Cc: Guangwu Zhang <guazhang@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>

When we use direct_IO with an NFS backing store, we can trigger a WARNING in __set_page_dirty(), as below, since we're dirtying the page unnecessarily in nfs_direct_read_completion(). To fix, replicate the logic in commit 53cbf3b ("fs: direct-io: don't dirtying pages for ITER_BVEC/ITER_KVEC direct read"). Other filesystems that implement direct_IO handle this; most use blockdev_direct_IO(). ceph and cifs have similar logic. mount 127.0.0.1:/export /nfs dd if=/dev/zero of=/nfs/image bs=1M count=200 losetup --direct-io=on -f /nfs/image mkfs.btrfs /dev/loop0 mount -t btrfs /dev/loop0 /mnt/ kernel: WARNING: CPU: 0 PID: 8067 at fs/buffer.c:580 __set_page_dirty+0xaf/0xd0 kernel: Modules linked in: loop(E) nfsv3(E) rpcsec_gss_krb5(E) nfsv4(E) dns_resolver(E) nfs(E) fscache(E) nfsd(E) auth_rpcgss(E) nfs_acl(E) lockd(E) grace(E) fuse(E) tun(E) ip6t_rpfilter(E) ipt_REJECT(E) nf_ kernel: snd_seq(E) snd_seq_device(E) snd_pcm(E) video(E) snd_timer(E) snd(E) soundcore(E) ip_tables(E) xfs(E) libcrc32c(E) sd_mod(E) sr_mod(E) cdrom(E) ata_generic(E) pata_acpi(E) crc32c_intel(E) ahci(E) li kernel: CPU: 0 PID: 8067 Comm: kworker/0:2 Tainted: G E 4.20.0-rc1.master.20181111.ol7.x86_64 #1 kernel: Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 kernel: Workqueue: nfsiod rpc_async_release [sunrpc] kernel: RIP: 0010:__set_page_dirty+0xaf/0xd0 kernel: Code: c3 48 8b 02 f6 c4 04 74 d4 48 89 df e8 ba 05 f7 ff 48 89 c6 eb cb 48 8b 43 08 a8 01 75 1f 48 89 d8 48 8b 00 a8 04 74 02 eb 87 <0f> 0b eb 83 48 83 e8 01 eb 9f 48 83 ea 01 0f 1f 00 eb 8b 48 83 e8 kernel: RSP: 0000:ffffc1c8825b7d78 EFLAGS: 00013046 kernel: RAX: 000fffffc0020089 RBX: fffff2b603308b80 RCX: 0000000000000001 kernel: RDX: 0000000000000001 RSI: ffff9d11478115c8 RDI: ffff9d11478115d0 kernel: RBP: ffffc1c8825b7da0 R08: 0000646f6973666e R09: 8080808080808080 kernel: R10: 0000000000000001 R11: 0000000000000000 R12: ffff9d11478115d0 kernel: R13: ffff9d11478115c8 R14: 0000000000003246 R15: 0000000000000001 kernel: FS: 0000000000000000(0000) GS:ffff9d115ba00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00007f408686f640 CR3: 0000000104d8e004 CR4: 00000000000606f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: Call Trace: kernel: __set_page_dirty_buffers+0xb6/0x110 kernel: set_page_dirty+0x52/0xb0 kernel: nfs_direct_read_completion+0xc4/0x120 [nfs] kernel: nfs_pgio_release+0x10/0x20 [nfs] kernel: rpc_free_task+0x30/0x70 [sunrpc] kernel: rpc_async_release+0x12/0x20 [sunrpc] kernel: process_one_work+0x174/0x390 kernel: worker_thread+0x4f/0x3e0 kernel: kthread+0x102/0x140 kernel: ? drain_workqueue+0x130/0x130 kernel: ? kthread_stop+0x110/0x110 kernel: ret_from_fork+0x35/0x40 kernel: ---[ end trace 01341980905412c9 ]--- Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> [forward-ported to v4.20] Signed-off-by: Calum Mackay <calum.mackay@oracle.com> Reviewed-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>

Frank Schreiner reported, that since kernel 4.18 he faces sysfs-warnings when loading modules on a 32-bit kernel. Here is one such example: sysfs: cannot create duplicate filename '/module/nfs/sections/.text' CPU: 0 PID: 98 Comm: modprobe Not tainted 4.18.0-2-parisc #1 Debian 4.18.10-2 Backtrace: [<1017ce2c>] show_stack+0x3c/0x50 [<107a7210>] dump_stack+0x28/0x38 [<103f900c>] sysfs_warn_dup+0x88/0xac [<103f8b1c>] sysfs_add_file_mode_ns+0x164/0x1d0 [<103f9e70>] internal_create_group+0x11c/0x304 [<103fa0a0>] sysfs_create_group+0x48/0x60 [<1022abe8>] load_module.constprop.35+0x1f9c/0x23b8 [<1022b278>] sys_finit_module+0xd0/0x11c [<101831dc>] syscall_exit+0x0/0x14 This warning gets triggered by the fact, that due to commit 24b6c22 ("parisc: Build kernel without -ffunction-sections") we now get multiple .text sections in the kernel modules for which sysfs_create_group() can't create multiple virtual files. This patch works around the problem by re-enabling the -ffunction-sections compiler option for modules, while keeping it disabled for the non-module kernel code. Reported-by: Frank Scheiner <frank.scheiner@web.de> Fixes: 24b6c22 ("parisc: Build kernel without -ffunction-sections") Cc: <stable@vger.kernel.org> # v4.18+ Signed-off-by: Helge Deller <deller@gmx.de>

The intermediate variable in the PERCPU_PTR() macro results in a kernel panic on boot [1] due to a compiler bug seen when compiling the kernel (+ KASAN) with gcc 11.3.1, but not when compiling with latest gcc (v14.2)/clang(v18.1). To solve it, remove the intermediate variable (which is not needed) and keep the casting that resolves the address space checks. [1] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] CPU: 0 UID: 0 PID: 547 Comm: iptables Not tainted 6.13.0-rc1_external_tested-master #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:nf_ct_netns_do_get+0x139/0x540 Code: 03 00 00 48 81 c4 88 00 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 4d 8d 75 08 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e 27 03 00 00 41 8b 45 08 83 c0 RSP: 0018:ffff888116df75e8 EFLAGS: 00010207 RAX: dffffc0000000000 RBX: 1ffff11022dbeebe RCX: ffffffff839a2382 RDX: 0000000000000003 RSI: 0000000000000008 RDI: ffff88842ec46d10 RBP: 0000000000000002 R08: 0000000000000000 R09: fffffbfff0b0860c R10: ffff888116df75e8 R11: 0000000000000001 R12: ffffffff879d6a80 R13: 0000000000000016 R14: 000000000000001e R15: ffff888116df7908 FS: 00007fba01646740(0000) GS:ffff88842ec00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055bd901800d8 CR3: 00000001205f0003 CR4: 0000000000172eb0 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? __mutex_lock+0x2c2/0x1d70 ? nf_ct_netns_do_get+0x139/0x540 ? nf_ct_netns_do_get+0xb5/0x540 ? net_generic+0x1f0/0x1f0 ? __create_object+0x5e/0x80 xt_check_target+0x1f0/0x930 ? textify_hooks.constprop.0+0x110/0x110 ? pcpu_alloc_noprof+0x7cd/0xcf0 ? xt_find_target+0x148/0x1e0 find_check_entry.constprop.0+0x6c0/0x920 ? get_info+0x380/0x380 ? __virt_addr_valid+0x1df/0x3b0 ? kasan_quarantine_put+0xe3/0x200 ? kfree+0x13e/0x3d0 ? translate_table+0xaf5/0x1750 translate_table+0xbd8/0x1750 ? ipt_unregister_table_exit+0x30/0x30 ? __might_fault+0xbb/0x170 do_ipt_set_ctl+0x408/0x1340 ? nf_sockopt_find.constprop.0+0x17b/0x1f0 ? lock_downgrade+0x680/0x680 ? lockdep_hardirqs_on_prepare+0x284/0x400 ? ipt_register_table+0x440/0x440 ? bit_wait_timeout+0x160/0x160 nf_setsockopt+0x6f/0xd0 raw_setsockopt+0x7e/0x200 ? raw_bind+0x590/0x590 ? do_user_addr_fault+0x812/0xd20 do_sock_setsockopt+0x1e2/0x3f0 ? move_addr_to_user+0x90/0x90 ? lock_downgrade+0x680/0x680 __sys_setsockopt+0x9e/0x100 __x64_sys_setsockopt+0xb9/0x150 ? do_syscall_64+0x33/0x140 do_syscall_64+0x6d/0x140 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7fba015134ce Code: 0f 1f 40 00 48 8b 15 59 69 0e 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b1 0f 1f 00 f3 0f 1e fa 49 89 ca b8 36 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 0a c3 66 0f 1f 84 00 00 00 00 00 48 8b 15 21 RSP: 002b:00007ffd9de6f388 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: ffffffffffffffda RBX: 000055bd9017f490 RCX: 00007fba015134ce RDX: 0000000000000040 RSI: 0000000000000000 RDI: 0000000000000004 RBP: 0000000000000500 R08: 0000000000000560 R09: 0000000000000052 R10: 000055bd901800e0 R11: 0000000000000246 R12: 000055bd90180140 R13: 000055bd901800e0 R14: 000055bd9017f498 R15: 000055bd9017ff10 </TASK> Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc mlx4_ib mlx4_en mlx4_core rpcrdma rdma_ucm ib_uverbs ib_iser libiscsi scsi_transport_iscsi fuse ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_core ---[ end trace 0000000000000000 ]--- [akpm@linux-foundation.org: simplification, per Uros] Link: https://lkml.kernel.org/r/20241219121828.2120780-1-gal@nvidia.com Fixes: dabddd6 ("percpu: cast percpu pointer in PERCPU_PTR() via unsigned long") Signed-off-by: Gal Pressman <gal@nvidia.com> Closes: https://lore.kernel.org/all/7590f546-4021-4602-9252-0d525de35b52@nvidia.com Cc: Uros Bizjak <ubizjak@gmail.com> Cc: Bill Wendling <morbo@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dennis Zhou <dennis@kernel.org> Cc: Justin Stitt <justinstitt@google.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

When driver processes the internal state change command, it use an asynchronous thread to process the command operation. If the main thread detects that the task has timed out, the asynchronous thread will panic when executing the completion notification because the main thread completion object has been released. BUG: unable to handle page fault for address: fffffffffffffff8 PGD 1f283a067 P4D 1f283a067 PUD 1f283c067 PMD 0 Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:complete_all+0x3e/0xa0 [...] Call Trace: <TASK> ? __die_body+0x68/0xb0 ? page_fault_oops+0x379/0x3e0 ? exc_page_fault+0x69/0xa0 ? asm_exc_page_fault+0x22/0x30 ? complete_all+0x3e/0xa0 fsm_main_thread+0xa3/0x9c0 [mtk_t7xx (HASH:1400 5)] ? __pfx_autoremove_wake_function+0x10/0x10 kthread+0xd8/0x110 ? __pfx_fsm_main_thread+0x10/0x10 [mtk_t7xx (HASH:1400 5)] ? __pfx_kthread+0x10/0x10 ret_from_fork+0x38/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> [...] CR2: fffffffffffffff8 ---[ end trace 0000000000000000 ]--- Use the reference counter to ensure safe release as Sergey suggests: https://lore.kernel.org/all/da90f64c-260a-4329-87bf-1f9ff20a5951@gmail.com/ Fixes: 13e920d ("net: wwan: t7xx: Add core components") Signed-off-by: Jinjian Song <jinjian.song@fibocom.com> Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Link: https://patch.msgid.link/20241224041552.8711-1-jinjian.song@fibocom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found by syzbot. Rework vlan_get_tci() to not touch skb at all, so that it can be used from many cpus on the same skb. Add a const qualifier to skb argument. [1] skbuff: skb_under_panic: text:ffffffff8a8da482 len:32 put:14 head:ffff88807a1d5800 data:ffff88807a1d5810 tail:0x14 end:0x140 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:206 ! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 0 UID: 0 PID: 5880 Comm: syz-executor172 Not tainted 6.13.0-rc3-syzkaller-00762-g9268abe611b0 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:skb_panic net/core/skbuff.c:206 [inline] RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216 Code: 0b 8d 48 c7 c6 9e 6c 26 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 3a 5a 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 RSP: 0018:ffffc90003baf5b8 EFLAGS: 00010286 RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 8565c1eec37aa000 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: ffff88802616fb50 R08: ffffffff817f0a4c R09: 1ffff92000775e50 R10: dffffc0000000000 R11: fffff52000775e51 R12: 0000000000000140 R13: ffff88807a1d5800 R14: ffff88807a1d5810 R15: 0000000000000014 FS: 00007fa03261f6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffd65753000 CR3: 0000000031720000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> skb_push+0xe5/0x100 net/core/skbuff.c:2636 vlan_get_tci+0x272/0x550 net/packet/af_packet.c:565 packet_recvmsg+0x13c9/0x1ef0 net/packet/af_packet.c:3616 sock_recvmsg_nosec net/socket.c:1044 [inline] sock_recvmsg+0x22f/0x280 net/socket.c:1066 ____sys_recvmsg+0x1c6/0x480 net/socket.c:2814 ___sys_recvmsg net/socket.c:2856 [inline] do_recvmmsg+0x426/0xab0 net/socket.c:2951 __sys_recvmmsg net/socket.c:3025 [inline] __do_sys_recvmmsg net/socket.c:3048 [inline] __se_sys_recvmmsg net/socket.c:3041 [inline] __x64_sys_recvmmsg+0x199/0x250 net/socket.c:3041 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 Fixes: 79eecf6 ("af_packet: Handle outgoing VLAN packets without hardware offloading") Reported-by: syzbot+8400677f3fd43f37d3bc@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/6772c485.050a0220.2f3838.04c6.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Chengen Du <chengen.du@canonical.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20241230161004.2681892-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found by syzbot. Rework vlan_get_protocol_dgram() to not touch skb at all, so that it can be used from many cpus on the same skb. Add a const qualifier to skb argument. [1] skbuff: skb_under_panic: text:ffffffff8a8ccd05 len:29 put:14 head:ffff88807fc8e400 data:ffff88807fc8e3f4 tail:0x11 end:0x140 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:206 ! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 UID: 0 PID: 5892 Comm: syz-executor883 Not tainted 6.13.0-rc4-syzkaller-00054-gd6ef8b40d075 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:skb_panic net/core/skbuff.c:206 [inline] RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216 Code: 0b 8d 48 c7 c6 86 d5 25 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 5a 69 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 RSP: 0018:ffffc900038d7638 EFLAGS: 00010282 RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 609ffd18ea660600 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: ffff88802483c8d0 R08: ffffffff817f0a8c R09: 1ffff9200071ae60 R10: dffffc0000000000 R11: fffff5200071ae61 R12: 0000000000000140 R13: ffff88807fc8e400 R14: ffff88807fc8e3f4 R15: 0000000000000011 FS: 00007fbac5e006c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fbac5e00d58 CR3: 000000001238e000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> skb_push+0xe5/0x100 net/core/skbuff.c:2636 vlan_get_protocol_dgram+0x165/0x290 net/packet/af_packet.c:585 packet_recvmsg+0x948/0x1ef0 net/packet/af_packet.c:3552 sock_recvmsg_nosec net/socket.c:1033 [inline] sock_recvmsg+0x22f/0x280 net/socket.c:1055 ____sys_recvmsg+0x1c6/0x480 net/socket.c:2803 ___sys_recvmsg net/socket.c:2845 [inline] do_recvmmsg+0x426/0xab0 net/socket.c:2940 __sys_recvmmsg net/socket.c:3014 [inline] __do_sys_recvmmsg net/socket.c:3037 [inline] __se_sys_recvmmsg net/socket.c:3030 [inline] __x64_sys_recvmmsg+0x199/0x250 net/socket.c:3030 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Fixes: 79eecf6 ("af_packet: Handle outgoing VLAN packets without hardware offloading") Reported-by: syzbot+74f70bb1cb968bf09e4f@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/6772c485.050a0220.2f3838.04c5.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Chengen Du <chengen.du@canonical.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20241230161004.2681892-2-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

[BUG] Syzbot reported a crash with the following call trace: BTRFS info (device loop0): scrub: started on devid 1 BUG: kernel NULL pointer dereference, address: 0000000000000208 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 106e70067 P4D 106e70067 PUD 107143067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 UID: 0 PID: 689 Comm: repro Kdump: loaded Tainted: G O 6.13.0-rc4-custom+ thesofproject#206 Tainted: [O]=OOT_MODULE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022 RIP: 0010:find_first_extent_item+0x26/0x1f0 [btrfs] Call Trace: <TASK> scrub_find_fill_first_stripe+0x13d/0x3b0 [btrfs] scrub_simple_mirror+0x175/0x260 [btrfs] scrub_stripe+0x5d4/0x6c0 [btrfs] scrub_chunk+0xbb/0x170 [btrfs] scrub_enumerate_chunks+0x2f4/0x5f0 [btrfs] btrfs_scrub_dev+0x240/0x600 [btrfs] btrfs_ioctl+0x1dc8/0x2fa0 [btrfs] ? do_sys_openat2+0xa5/0xf0 __x64_sys_ioctl+0x97/0xc0 do_syscall_64+0x4f/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> [CAUSE] The reproducer is using a corrupted image where extent tree root is corrupted, thus forcing to use "rescue=all,ro" mount option to mount the image. Then it triggered a scrub, but since scrub relies on extent tree to find where the data/metadata extents are, scrub_find_fill_first_stripe() relies on an non-empty extent root. But unfortunately scrub_find_fill_first_stripe() doesn't really expect an NULL pointer for extent root, it use extent_root to grab fs_info and triggered a NULL pointer dereference. [FIX] Add an extra check for a valid extent root at the beginning of scrub_find_fill_first_stripe(). The new error path is introduced by 42437a6 ("btrfs: introduce mount option rescue=ignorebadroots"), but that's pretty old, and later commit b979547 ("btrfs: scrub: introduce helper to find and fill sector info for a scrub_stripe") changed how we do scrub. So for kernels older than 6.6, the fix will need manual backport. Reported-by: syzbot+339e9dbe3a2ca419b85d@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/67756935.050a0220.25abdd.0a12.GAE@google.com/ Fixes: 42437a6 ("btrfs: introduce mount option rescue=ignorebadroots") Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>

Since the input data length passed to zlib_compress_folios() can be arbitrary, always setting strm.avail_in to a multiple of PAGE_SIZE may cause read-in bytes to exceed the input range. Currently this triggers an assert in btrfs_compress_folios() on the debug kernel (see below). Fix strm.avail_in calculation for S390 hardware acceleration path. assertion failed: *total_in <= orig_len, in fs/btrfs/compression.c:1041 ------------[ cut here ]------------ kernel BUG at fs/btrfs/compression.c:1041! monitor event: 0040 ilc:2 [#1] PREEMPT SMP CPU: 16 UID: 0 PID: 325 Comm: kworker/u273:3 Not tainted 6.13.0-20241204.rc1.git6.fae3b21430ca.300.fc41.s390x+debug #1 Hardware name: IBM 3931 A01 703 (z/VM 7.4.0) Workqueue: btrfs-delalloc btrfs_work_helper Krnl PSW : 0704d00180000000 0000021761df6538 (btrfs_compress_folios+0x198/0x1a0) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: 0000000080000000 0000000000000001 0000000000000047 0000000000000000 0000000000000006 ffffff01757bb000 000001976232fcc0 000000000000130c 000001976232fcd0 000001976232fcc8 00000118ff4a0e30 0000000000000001 00000111821ab400 0000011100000000 0000021761df6534 000001976232fb58 Krnl Code: 0000021761df6528: c020006f5ef4 larl %r2,0000021762be2310 0000021761df652e: c0e5ffbd09d5 brasl %r14,00000217615978d8 #0000021761df6534: af000000 mc 0,0 >0000021761df6538: 0707 bcr 0,%r7 0000021761df653a: 0707 bcr 0,%r7 0000021761df653c: 0707 bcr 0,%r7 0000021761df653e: 0707 bcr 0,%r7 0000021761df6540: c004004bb7ec brcl 0,000002176276d518 Call Trace: [<0000021761df6538>] btrfs_compress_folios+0x198/0x1a0 ([<0000021761df6534>] btrfs_compress_folios+0x194/0x1a0) [<0000021761d97788>] compress_file_range+0x3b8/0x6d0 [<0000021761dcee7c>] btrfs_work_helper+0x10c/0x160 [<0000021761645760>] process_one_work+0x2b0/0x5d0 [<000002176164637e>] worker_thread+0x20e/0x3e0 [<000002176165221a>] kthread+0x15a/0x170 [<00000217615b859c>] __ret_from_fork+0x3c/0x60 [<00000217626e72d2>] ret_from_fork+0xa/0x38 INFO: lockdep is turned off. Last Breaking-Event-Address: [<0000021761597924>] _printk+0x4c/0x58 Kernel panic - not syncing: Fatal exception: panic_on_oops Fixes: fd1e75d ("btrfs: make compression path to be subpage compatible") CC: stable@vger.kernel.org # 6.12+ Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com> Signed-off-by: David Sterba <dsterba@suse.com>

DC driver is using two different values to define the maximum number of surfaces: MAX_SURFACES and MAX_SURFACE_NUM. Consolidate MAX_SURFACES as the unique definition for surface updates across DC. It fixes page fault faced by Cosmic users on AMD display versions that support two overlay planes, since the introduction of cursor overlay mode. [Nov26 21:33] BUG: unable to handle page fault for address: 0000000051d0f08b [ +0.000015] #PF: supervisor read access in kernel mode [ +0.000006] #PF: error_code(0x0000) - not-present page [ +0.000005] PGD 0 P4D 0 [ +0.000007] Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI [ +0.000006] CPU: 4 PID: 71 Comm: kworker/u32:6 Not tainted 6.10.0+ thesofproject#300 [ +0.000006] Hardware name: Valve Jupiter/Jupiter, BIOS F7A0131 01/30/2024 [ +0.000007] Workqueue: events_unbound commit_work [drm_kms_helper] [ +0.000040] RIP: 0010:copy_stream_update_to_stream.isra.0+0x30d/0x750 [amdgpu] [ +0.000847] Code: 8b 10 49 89 94 24 f8 00 00 00 48 8b 50 08 49 89 94 24 00 01 00 00 8b 40 10 41 89 84 24 08 01 00 00 49 8b 45 78 48 85 c0 74 0b <0f> b6 00 41 88 84 24 90 64 00 00 49 8b 45 60 48 85 c0 74 3b 48 8b [ +0.000010] RSP: 0018:ffffc203802f79a0 EFLAGS: 00010206 [ +0.000009] RAX: 0000000051d0f08b RBX: 0000000000000004 RCX: ffff9f964f0a8070 [ +0.000004] RDX: ffff9f9710f90e40 RSI: ffff9f96600c8000 RDI: ffff9f964f000000 [ +0.000004] RBP: ffffc203802f79f8 R08: 0000000000000000 R09: 0000000000000000 [ +0.000005] R10: 0000000000000000 R11: 0000000000000000 R12: ffff9f96600c8000 [ +0.000004] R13: ffff9f9710f90e40 R14: ffff9f964f000000 R15: ffff9f96600c8000 [ +0.000004] FS: 0000000000000000(0000) GS:ffff9f9970000000(0000) knlGS:0000000000000000 [ +0.000005] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000005] CR2: 0000000051d0f08b CR3: 00000002e6a20000 CR4: 0000000000350ef0 [ +0.000005] Call Trace: [ +0.000011] <TASK> [ +0.000010] ? __die_body.cold+0x19/0x27 [ +0.000012] ? page_fault_oops+0x15a/0x2d0 [ +0.000014] ? exc_page_fault+0x7e/0x180 [ +0.000009] ? asm_exc_page_fault+0x26/0x30 [ +0.000013] ? copy_stream_update_to_stream.isra.0+0x30d/0x750 [amdgpu] [ +0.000739] ? dc_commit_state_no_check+0xd6c/0xe70 [amdgpu] [ +0.000470] update_planes_and_stream_state+0x49b/0x4f0 [amdgpu] [ +0.000450] ? srso_return_thunk+0x5/0x5f [ +0.000009] ? commit_minimal_transition_state+0x239/0x3d0 [amdgpu] [ +0.000446] update_planes_and_stream_v2+0x24a/0x590 [amdgpu] [ +0.000464] ? srso_return_thunk+0x5/0x5f [ +0.000009] ? sort+0x31/0x50 [ +0.000007] ? amdgpu_dm_atomic_commit_tail+0x159f/0x3a30 [amdgpu] [ +0.000508] ? srso_return_thunk+0x5/0x5f [ +0.000009] ? amdgpu_crtc_get_scanout_position+0x28/0x40 [amdgpu] [ +0.000377] ? srso_return_thunk+0x5/0x5f [ +0.000009] ? drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x160/0x390 [drm] [ +0.000058] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? dma_fence_default_wait+0x8c/0x260 [ +0.000010] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? wait_for_completion_timeout+0x13b/0x170 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? dma_fence_wait_timeout+0x108/0x140 [ +0.000010] ? commit_tail+0x94/0x130 [drm_kms_helper] [ +0.000024] ? process_one_work+0x177/0x330 [ +0.000008] ? worker_thread+0x266/0x3a0 [ +0.000006] ? __pfx_worker_thread+0x10/0x10 [ +0.000004] ? kthread+0xd2/0x100 [ +0.000006] ? __pfx_kthread+0x10/0x10 [ +0.000006] ? ret_from_fork+0x34/0x50 [ +0.000004] ? __pfx_kthread+0x10/0x10 [ +0.000005] ? ret_from_fork_asm+0x1a/0x30 [ +0.000011] </TASK> Fixes: 1b04dcc ("drm/amd/display: Introduce overlay cursor mode") Suggested-by: Leo Li <sunpeng.li@amd.com> Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3693 Signed-off-by: Melissa Wen <mwen@igalia.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> (cherry picked from commit 1c86c81) Cc: stable@vger.kernel.org

dm_get_plane_scale doesn't take into account plane scaled size equal to zero, leading to a kernel oops due to division by zero. Fix by setting out-scale size as zero when the dst size is zero, similar to what is done by drm_calc_scale(). This issue started with the introduction of cursor ovelay mode that uses this function to assess cursor mode changes via dm_crtc_get_cursor_mode() before checking plane state. [Dec17 17:14] Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI [ +0.000018] CPU: 5 PID: 1660 Comm: surface-DP-1 Not tainted 6.10.0+ thesofproject#231 [ +0.000007] Hardware name: Valve Jupiter/Jupiter, BIOS F7A0131 01/30/2024 [ +0.000004] RIP: 0010:dm_get_plane_scale+0x3f/0x60 [amdgpu] [ +0.000553] Code: 44 0f b7 41 3a 44 0f b7 49 3e 83 e0 0f 48 0f a3 c2 73 21 69 41 28 e8 03 00 00 31 d2 41 f7 f1 31 d2 89 06 69 41 2c e8 03 00 00 <41> f7 f0 89 07 e9 d7 d8 7e e9 44 89 c8 45 89 c1 41 89 c0 eb d4 66 [ +0.000005] RSP: 0018:ffffa8df0de6b8a0 EFLAGS: 00010246 [ +0.000006] RAX: 00000000000003e8 RBX: ffff9ac65c1f6e00 RCX: ffff9ac65d055500 [ +0.000003] RDX: 0000000000000000 RSI: ffffa8df0de6b8b0 RDI: ffffa8df0de6b8b4 [ +0.000004] RBP: ffff9ac64e7a5800 R08: 0000000000000000 R09: 0000000000000a00 [ +0.000003] R10: 00000000000000ff R11: 0000000000000054 R12: ffff9ac6d0700010 [ +0.000003] R13: ffff9ac65d054f00 R14: ffff9ac65d055500 R15: ffff9ac64e7a60a0 [ +0.000004] FS: 00007f869ea00640(0000) GS:ffff9ac970080000(0000) knlGS:0000000000000000 [ +0.000004] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000003] CR2: 000055ca701becd0 CR3: 000000010e7f2000 CR4: 0000000000350ef0 [ +0.000004] Call Trace: [ +0.000007] <TASK> [ +0.000006] ? __die_body.cold+0x19/0x27 [ +0.000009] ? die+0x2e/0x50 [ +0.000007] ? do_trap+0xca/0x110 [ +0.000007] ? do_error_trap+0x6a/0x90 [ +0.000006] ? dm_get_plane_scale+0x3f/0x60 [amdgpu] [ +0.000504] ? exc_divide_error+0x38/0x50 [ +0.000005] ? dm_get_plane_scale+0x3f/0x60 [amdgpu] [ +0.000488] ? asm_exc_divide_error+0x1a/0x20 [ +0.000011] ? dm_get_plane_scale+0x3f/0x60 [amdgpu] [ +0.000593] dm_crtc_get_cursor_mode+0x33f/0x430 [amdgpu] [ +0.000562] amdgpu_dm_atomic_check+0x2ef/0x1770 [amdgpu] [ +0.000501] drm_atomic_check_only+0x5e1/0xa30 [drm] [ +0.000047] drm_mode_atomic_ioctl+0x832/0xcb0 [drm] [ +0.000050] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 [drm] [ +0.000047] drm_ioctl_kernel+0xb3/0x100 [drm] [ +0.000062] drm_ioctl+0x27a/0x4f0 [drm] [ +0.000049] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 [drm] [ +0.000055] amdgpu_drm_ioctl+0x4e/0x90 [amdgpu] [ +0.000360] __x64_sys_ioctl+0x97/0xd0 [ +0.000010] do_syscall_64+0x82/0x190 [ +0.000008] ? __pfx_drm_mode_createblob_ioctl+0x10/0x10 [drm] [ +0.000044] ? srso_return_thunk+0x5/0x5f [ +0.000006] ? drm_ioctl_kernel+0xb3/0x100 [drm] [ +0.000040] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? __check_object_size+0x50/0x220 [ +0.000007] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? drm_ioctl+0x2a4/0x4f0 [drm] [ +0.000039] ? __pfx_drm_mode_createblob_ioctl+0x10/0x10 [drm] [ +0.000043] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? __pm_runtime_suspend+0x69/0xc0 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? amdgpu_drm_ioctl+0x71/0x90 [amdgpu] [ +0.000366] ? srso_return_thunk+0x5/0x5f [ +0.000006] ? syscall_exit_to_user_mode+0x77/0x210 [ +0.000007] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? do_syscall_64+0x8e/0x190 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000006] ? do_syscall_64+0x8e/0x190 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000007] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000008] RIP: 0033:0x55bb7cd962bc [ +0.000007] Code: 4c 89 6c 24 18 4c 89 64 24 20 4c 89 74 24 28 0f 57 c0 0f 11 44 24 30 89 c7 48 8d 54 24 08 b8 10 00 00 00 be bc 64 38 c0 0f 05 <49> 89 c7 48 83 3b 00 74 09 4c 89 c7 ff 15 62 64 99 00 48 83 7b 18 [ +0.000005] RSP: 002b:00007f869e9f4da0 EFLAGS: 00000217 ORIG_RAX: 0000000000000010 [ +0.000007] RAX: ffffffffffffffda RBX: 00007f869e9f4fb8 RCX: 000055bb7cd962bc [ +0.000004] RDX: 00007f869e9f4da8 RSI: 00000000c03864bc RDI: 000000000000003b [ +0.000003] RBP: 000055bb9ddcbcc0 R08: 00007f86541b9920 R09: 0000000000000009 [ +0.000004] R10: 0000000000000004 R11: 0000000000000217 R12: 00007f865406c6b0 [ +0.000003] R13: 00007f86541b5290 R14: 00007f865410b700 R15: 000055bb9ddcbc18 [ +0.000009] </TASK> Fixes: 1b04dcc ("drm/amd/display: Introduce overlay cursor mode") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3729 Reported-by: Fabio Scaccabarozzi <fsvm88@gmail.com> Co-developed-by: Fabio Scaccabarozzi <fsvm88@gmail.com> Signed-off-by: Fabio Scaccabarozzi <fsvm88@gmail.com> Signed-off-by: Melissa Wen <mwen@igalia.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> (cherry picked from commit ab75a0d) Cc: stable@vger.kernel.org

die() can be called in exception handler, and therefore cannot sleep. However, die() takes spinlock_t which can sleep with PREEMPT_RT enabled. That causes the following warning: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 285, name: mutex preempt_count: 110001, expected: 0 RCU nest depth: 0, expected: 0 CPU: 0 UID: 0 PID: 285 Comm: mutex Not tainted 6.12.0-rc7-00022-ge19049cf7d56-dirty thesofproject#234 Hardware name: riscv-virtio,qemu (DT) Call Trace: dump_backtrace+0x1c/0x24 show_stack+0x2c/0x38 dump_stack_lvl+0x5a/0x72 dump_stack+0x14/0x1c __might_resched+0x130/0x13a rt_spin_lock+0x2a/0x5c die+0x24/0x112 do_trap_insn_illegal+0xa0/0xea _new_vmalloc_restore_context_a0+0xcc/0xd8 Oops - illegal instruction [#1] Switch to use raw_spinlock_t, which does not sleep even with PREEMPT_RT enabled. Fixes: 76d2a04 ("RISC-V: Init and Halt Code") Signed-off-by: Nam Cao <namcao@linutronix.de> Cc: stable@vger.kernel.org Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20241118091333.1185288-1-namcao@linutronix.de Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>

If GuC fails to load, the driver wedges, but in the process it tries to do stuff that may not be initialized yet. This moves the xe_gt_tlb_invalidation_init() to be done earlier: as its own doc says, it's a software-only initialization and should had been named with the _early() suffix. Move it to be called by xe_gt_init_early(), so the locks and seqno are initialized, avoiding a NULL ptr deref when wedging: xe 0000:03:00.0: [drm] *ERROR* GT0: load failed: status: Reset = 0, BootROM = 0x50, UKernel = 0x00, MIA = 0x00, Auth = 0x01 xe 0000:03:00.0: [drm] *ERROR* GT0: firmware signature verification failed xe 0000:03:00.0: [drm] *ERROR* CRITICAL: Xe has declared device 0000:03:00.0 as wedged. ... BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 9 UID: 0 PID: 3908 Comm: modprobe Tainted: G U W 6.13.0-rc4-xe+ #3 Tainted: [U]=USER, [W]=WARN Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-S ADP-S DDR5 UDIMM CRB, BIOS ADLSFWI1.R00.3275.A00.2207010640 07/01/2022 RIP: 0010:xe_gt_tlb_invalidation_reset+0x75/0x110 [xe] This can be easily triggered by poking the GuC binary to force a signature failure. There will still be an extra message, xe 0000:03:00.0: [drm] *ERROR* GT0: GuC mmio request 0x4100: no reply 0x4100 but that's better than a NULL ptr deref. Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/3956 Fixes: c9474b7 ("drm/xe: Wedge the entire device") Reviewed-by: Matthew Brost <matthew.brost@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20250103001111.331684-2-lucas.demarchi@intel.com Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> (cherry picked from commit 5001ef3) Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>

We found a timeout problem with the pldm command on our system. The reason is that the MCTP-I3C driver has a race condition when receiving multiple-packet messages in multi-thread, resulting in a wrong packet order problem. We identified this problem by adding a debug message to the mctp_i3c_read function. According to the MCTP spec, a multiple-packet message must be composed in sequence, and if there is a wrong sequence, the whole message will be discarded and wait for the next SOM. For example, SOM → Pkt Seq #2 → Pkt Seq #1 → Pkt Seq #3 → EOM. Therefore, we try to solve this problem by adding a mutex to the mctp_i3c_read function. Before the modification, when a command requesting a multiple-packet message response is sent consecutively, an error usually occurs within 100 loops. After the mutex, it can go through 40000 loops without any error, and it seems to run well. Fixes: c8755b2 ("mctp i3c: MCTP I3C driver") Signed-off-by: Leo Yang <Leo-Yang@quantatw.com> Link: https://patch.msgid.link/20250107031529.3296094-1-Leo-Yang@quantatw.com [pabeni@redhat.com: dropped already answered question from changelog] Signed-off-by: Paolo Abeni <pabeni@redhat.com>

When cmd_alloc_index(), fails cmd_work_handler() needs to complete ent->slotted before returning early. Otherwise the task which issued the command may hang: mlx5_core 0000:01:00.0: cmd_work_handler:877:(pid 3880418): failed to allocate command entry INFO: task kworker/13:2:4055883 blocked for more than 120 seconds. Not tainted 4.19.90-25.44.v2101.ky10.aarch64 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kworker/13:2 D 0 4055883 2 0x00000228 Workqueue: events mlx5e_tx_dim_work [mlx5_core] Call trace: __switch_to+0xe8/0x150 __schedule+0x2a8/0x9b8 schedule+0x2c/0x88 schedule_timeout+0x204/0x478 wait_for_common+0x154/0x250 wait_for_completion+0x28/0x38 cmd_exec+0x7a0/0xa00 [mlx5_core] mlx5_cmd_exec+0x54/0x80 [mlx5_core] mlx5_core_modify_cq+0x6c/0x80 [mlx5_core] mlx5_core_modify_cq_moderation+0xa0/0xb8 [mlx5_core] mlx5e_tx_dim_work+0x54/0x68 [mlx5_core] process_one_work+0x1b0/0x448 worker_thread+0x54/0x468 kthread+0x134/0x138 ret_from_fork+0x10/0x18 Fixes: 485d65e ("net/mlx5: Add a timeout to acquire the command queue semaphore") Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Acked-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20250108030009.68520-1-zhaochenguang@kylinos.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using the 'net' structure via 'current' is not recommended for different reasons. First, if the goal is to use it to read or write per-netns data, this is inconsistent with how the "generic" sysctl entries are doing: directly by only using pointers set to the table entry, e.g. table->data. Linked to that, the per-netns data should always be obtained from the table linked to the netns it had been created for, which may not coincide with the reader's or writer's netns. Another reason is that access to current->nsproxy->netns can oops if attempted when current->nsproxy had been dropped when the current task is exiting. This is what syzbot found, when using acct(2): Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] CPU: 1 UID: 0 PID: 5924 Comm: syz-executor Not tainted 6.13.0-rc5-syzkaller-00004-gccb98ccef0e5 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:proc_scheduler+0xc6/0x3c0 net/mptcp/ctrl.c:125 Code: 03 42 80 3c 38 00 0f 85 fe 02 00 00 4d 8b a4 24 08 09 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7c 24 28 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 02 00 00 4d 8b 7c 24 28 48 8d 84 24 c8 00 00 RSP: 0018:ffffc900034774e8 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 1ffff9200068ee9e RCX: ffffc90003477620 RDX: 0000000000000005 RSI: ffffffff8b08f91e RDI: 0000000000000028 RBP: 0000000000000001 R08: ffffc90003477710 R09: 0000000000000040 R10: 0000000000000040 R11: 00000000726f7475 R12: 0000000000000000 R13: ffffc90003477620 R14: ffffc90003477710 R15: dffffc0000000000 FS: 0000000000000000(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fee3cd452d8 CR3: 000000007d116000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> proc_sys_call_handler+0x403/0x5d0 fs/proc/proc_sysctl.c:601 __kernel_write_iter+0x318/0xa80 fs/read_write.c:612 __kernel_write+0xf6/0x140 fs/read_write.c:632 do_acct_process+0xcb0/0x14a0 kernel/acct.c:539 acct_pin_kill+0x2d/0x100 kernel/acct.c:192 pin_kill+0x194/0x7c0 fs/fs_pin.c:44 mnt_pin_kill+0x61/0x1e0 fs/fs_pin.c:81 cleanup_mnt+0x3ac/0x450 fs/namespace.c:1366 task_work_run+0x14e/0x250 kernel/task_work.c:239 exit_task_work include/linux/task_work.h:43 [inline] do_exit+0xad8/0x2d70 kernel/exit.c:938 do_group_exit+0xd3/0x2a0 kernel/exit.c:1087 get_signal+0x2576/0x2610 kernel/signal.c:3017 arch_do_signal_or_restart+0x90/0x7e0 arch/x86/kernel/signal.c:337 exit_to_user_mode_loop kernel/entry/common.c:111 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x150/0x2a0 kernel/entry/common.c:218 do_syscall_64+0xda/0x250 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fee3cb87a6a Code: Unable to access opcode bytes at 0x7fee3cb87a40. RSP: 002b:00007fffcccac688 EFLAGS: 00000202 ORIG_RAX: 0000000000000037 RAX: 0000000000000000 RBX: 00007fffcccac710 RCX: 00007fee3cb87a6a RDX: 0000000000000041 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000003 R08: 00007fffcccac6ac R09: 00007fffcccacac7 R10: 00007fffcccac710 R11: 0000000000000202 R12: 00007fee3cd49500 R13: 00007fffcccac6ac R14: 0000000000000000 R15: 00007fee3cd4b000 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:proc_scheduler+0xc6/0x3c0 net/mptcp/ctrl.c:125 Code: 03 42 80 3c 38 00 0f 85 fe 02 00 00 4d 8b a4 24 08 09 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d 7c 24 28 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 02 00 00 4d 8b 7c 24 28 48 8d 84 24 c8 00 00 RSP: 0018:ffffc900034774e8 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 1ffff9200068ee9e RCX: ffffc90003477620 RDX: 0000000000000005 RSI: ffffffff8b08f91e RDI: 0000000000000028 RBP: 0000000000000001 R08: ffffc90003477710 R09: 0000000000000040 R10: 0000000000000040 R11: 00000000726f7475 R12: 0000000000000000 R13: ffffc90003477620 R14: ffffc90003477710 R15: dffffc0000000000 FS: 0000000000000000(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fee3cd452d8 CR3: 000000007d116000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 ---------------- Code disassembly (best guess), 1 bytes skipped: 0: 42 80 3c 38 00 cmpb $0x0,(%rax,%r15,1) 5: 0f 85 fe 02 00 00 jne 0x309 b: 4d 8b a4 24 08 09 00 mov 0x908(%r12),%r12 12: 00 13: 48 b8 00 00 00 00 00 movabs $0xdffffc0000000000,%rax 1a: fc ff df 1d: 49 8d 7c 24 28 lea 0x28(%r12),%rdi 22: 48 89 fa mov %rdi,%rdx 25: 48 c1 ea 03 shr $0x3,%rdx * 29: 80 3c 02 00 cmpb $0x0,(%rdx,%rax,1) <-- trapping instruction 2d: 0f 85 cc 02 00 00 jne 0x2ff 33: 4d 8b 7c 24 28 mov 0x28(%r12),%r15 38: 48 rex.W 39: 8d .byte 0x8d 3a: 84 24 c8 test %ah,(%rax,%rcx,8) Here with 'net.mptcp.scheduler', the 'net' structure is not really needed, because the table->data already has a pointer to the current scheduler, the only thing needed from the per-netns data. Simply use 'data', instead of getting (most of the time) the same thing, but from a longer and indirect way. Fixes: 6963c50 ("mptcp: only allow set existing scheduler for net.mptcp.scheduler") Cc: stable@vger.kernel.org Reported-by: syzbot+e364f774c6f57f2c86d1@syzkaller.appspotmail.com Closes: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-2-5df34b2083e8@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Max Makarov reported kernel panic [1] in perf user callchain code. The reason for that is the race between uprobe_free_utask and bpf profiler code doing the perf user stack unwind and is triggered within uprobe_free_utask function: - after current->utask is freed and - before current->utask is set to NULL general protection fault, probably for non-canonical address 0x9e759c37ee555c76: 0000 [#1] SMP PTI RIP: 0010:is_uprobe_at_func_entry+0x28/0x80 ... ? die_addr+0x36/0x90 ? exc_general_protection+0x217/0x420 ? asm_exc_general_protection+0x26/0x30 ? is_uprobe_at_func_entry+0x28/0x80 perf_callchain_user+0x20a/0x360 get_perf_callchain+0x147/0x1d0 bpf_get_stackid+0x60/0x90 bpf_prog_9aac297fb833e2f5_do_perf_event+0x434/0x53b ? __smp_call_single_queue+0xad/0x120 bpf_overflow_handler+0x75/0x110 ... asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:__kmem_cache_free+0x1cb/0x350 ... ? uprobe_free_utask+0x62/0x80 ? acct_collect+0x4c/0x220 uprobe_free_utask+0x62/0x80 mm_release+0x12/0xb0 do_exit+0x26b/0xaa0 __x64_sys_exit+0x1b/0x20 do_syscall_64+0x5a/0x80 It can be easily reproduced by running following commands in separate terminals: # while :; do bpftrace -e 'uprobe:/bin/ls:_start { printf("hit\n"); }' -c ls; done # bpftrace -e 'profile:hz:100000 { @[ustack()] = count(); }' Fixing this by making sure current->utask pointer is set to NULL before we start to release the utask object. [1] grafana/pyroscope#3673 Fixes: cfa7f3d ("perf,x86: avoid missing caller address in stack traces captured in uprobe") Reported-by: Max Makarov <maxpain@linux.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/r/20250109141440.2692173-1-jolsa@kernel.org

When COWing a relocation tree path, at relocation.c:replace_path(), we can trigger a lockdep splat while we are in the btrfs_search_slot() call against the relocation root. This happens in that callchain at ctree.c:read_block_for_search() when we happen to find a child extent buffer already loaded through the fs tree with a lockdep class set to the fs tree. So when we attempt to lock that extent buffer through a relocation tree we have to reset the lockdep class to the class for a relocation tree, since a relocation tree has extent buffers that used to belong to a fs tree and may currently be already loaded (we swap extent buffers between the two trees at the end of replace_path()). However we are missing calls to btrfs_maybe_reset_lockdep_class() to reset the lockdep class at ctree.c:read_block_for_search() before we read lock an extent buffer, just like we did for btrfs_search_slot() in commit b40130b ("btrfs: fix lockdep splat with reloc root extent buffers"). So add the missing btrfs_maybe_reset_lockdep_class() calls before the attempts to read lock an extent buffer at ctree.c:read_block_for_search(). The lockdep splat was reported by syzbot and it looks like this: ====================================================== WARNING: possible circular locking dependency detected 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Not tainted ------------------------------------------------------ syz.0.0/5335 is trying to acquire lock: ffff8880545dbc38 (btrfs-tree-01){++++}-{4:4}, at: btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 but task is already holding lock: ffff8880545dba58 (btrfs-treloc-02/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (btrfs-treloc-02/1){+.+.}-{4:4}: reacquire_held_locks+0x3eb/0x690 kernel/locking/lockdep.c:5374 __lock_release kernel/locking/lockdep.c:5563 [inline] lock_release+0x396/0xa30 kernel/locking/lockdep.c:5870 up_write+0x79/0x590 kernel/locking/rwsem.c:1629 btrfs_force_cow_block+0x14b3/0x1fd0 fs/btrfs/ctree.c:660 btrfs_cow_block+0x371/0x830 fs/btrfs/ctree.c:755 btrfs_search_slot+0xc01/0x3180 fs/btrfs/ctree.c:2153 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #1 (btrfs-tree-01/1){+.+.}-{4:4}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_write_nested+0xa2/0x220 kernel/locking/rwsem.c:1693 btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 btrfs_init_new_buffer fs/btrfs/extent-tree.c:5052 [inline] btrfs_alloc_tree_block+0x41c/0x1440 fs/btrfs/extent-tree.c:5132 btrfs_force_cow_block+0x526/0x1fd0 fs/btrfs/ctree.c:573 btrfs_cow_block+0x371/0x830 fs/btrfs/ctree.c:755 btrfs_search_slot+0xc01/0x3180 fs/btrfs/ctree.c:2153 btrfs_insert_empty_items+0x9c/0x1a0 fs/btrfs/ctree.c:4351 btrfs_insert_empty_item fs/btrfs/ctree.h:688 [inline] btrfs_insert_inode_ref+0x2bb/0xf80 fs/btrfs/inode-item.c:330 btrfs_rename_exchange fs/btrfs/inode.c:7990 [inline] btrfs_rename2+0xcb7/0x2b90 fs/btrfs/inode.c:8374 vfs_rename+0xbdb/0xf00 fs/namei.c:5067 do_renameat2+0xd94/0x13f0 fs/namei.c:5224 __do_sys_renameat2 fs/namei.c:5258 [inline] __se_sys_renameat2 fs/namei.c:5255 [inline] __x64_sys_renameat2+0xce/0xe0 fs/namei.c:5255 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (btrfs-tree-01){++++}-{4:4}: check_prev_add kernel/locking/lockdep.c:3161 [inline] check_prevs_add kernel/locking/lockdep.c:3280 [inline] validate_chain+0x18ef/0x5920 kernel/locking/lockdep.c:3904 __lock_acquire+0x1397/0x2100 kernel/locking/lockdep.c:5226 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_read_nested+0xb5/0xa50 kernel/locking/rwsem.c:1649 btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 btrfs_tree_read_lock fs/btrfs/locking.h:188 [inline] read_block_for_search+0x718/0xbb0 fs/btrfs/ctree.c:1610 btrfs_search_slot+0x1274/0x3180 fs/btrfs/ctree.c:2237 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Chain exists of: btrfs-tree-01 --> btrfs-tree-01/1 --> btrfs-treloc-02/1 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(btrfs-treloc-02/1); lock(btrfs-tree-01/1); lock(btrfs-treloc-02/1); rlock(btrfs-tree-01); *** DEADLOCK *** 8 locks held by syz.0.0/5335: #0: ffff88801e3ae420 (sb_writers#13){.+.+}-{0:0}, at: mnt_want_write_file+0x5e/0x200 fs/namespace.c:559 #1: ffff888052c760d0 (&fs_info->reclaim_bgs_lock){+.+.}-{4:4}, at: __btrfs_balance+0x4c2/0x26b0 fs/btrfs/volumes.c:4183 #2: ffff888052c74850 (&fs_info->cleaner_mutex){+.+.}-{4:4}, at: btrfs_relocate_block_group+0x775/0xd90 fs/btrfs/relocation.c:4086 #3: ffff88801e3ae610 (sb_internal#2){.+.+}-{0:0}, at: merge_reloc_root+0xf11/0x1ad0 fs/btrfs/relocation.c:1659 #4: ffff888052c76470 (btrfs_trans_num_writers){++++}-{0:0}, at: join_transaction+0x405/0xda0 fs/btrfs/transaction.c:288 thesofproject#5: ffff888052c76498 (btrfs_trans_num_extwriters){++++}-{0:0}, at: join_transaction+0x405/0xda0 fs/btrfs/transaction.c:288 thesofproject#6: ffff8880545db878 (btrfs-tree-01/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 thesofproject#7: ffff8880545dba58 (btrfs-treloc-02/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 stack backtrace: CPU: 0 UID: 0 PID: 5335 Comm: syz.0.0 Not tainted 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_circular_bug+0x13a/0x1b0 kernel/locking/lockdep.c:2074 check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2206 check_prev_add kernel/locking/lockdep.c:3161 [inline] check_prevs_add kernel/locking/lockdep.c:3280 [inline] validate_chain+0x18ef/0x5920 kernel/locking/lockdep.c:3904 __lock_acquire+0x1397/0x2100 kernel/locking/lockdep.c:5226 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_read_nested+0xb5/0xa50 kernel/locking/rwsem.c:1649 btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 btrfs_tree_read_lock fs/btrfs/locking.h:188 [inline] read_block_for_search+0x718/0xbb0 fs/btrfs/ctree.c:1610 btrfs_search_slot+0x1274/0x3180 fs/btrfs/ctree.c:2237 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1ac6985d29 Code: ff ff c3 (...) RSP: 002b:00007f1ac63fe038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f1ac6b76160 RCX: 00007f1ac6985d29 RDX: 0000000020000180 RSI: 00000000c4009420 RDI: 0000000000000007 RBP: 00007f1ac6a01b08 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000001 R14: 00007f1ac6b76160 R15: 00007fffda145a88 </TASK> Reported-by: syzbot+63913e558c084f7f8fdc@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/677b3014.050a0220.3b53b0.0064.GAE@google.com/ Fixes: 9978599 ("btrfs: reduce lock contention when eb cache miss for btree search") Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>

…saction abort If while we are doing a direct IO write a transaction abort happens, we mark all existing ordered extents with the BTRFS_ORDERED_IOERR flag (done at btrfs_destroy_ordered_extents()), and then after that if we enter btrfs_split_ordered_extent() and the ordered extent has bytes left (meaning we have a bio that doesn't cover the whole ordered extent, see details at btrfs_extract_ordered_extent()), we will fail on the following assertion at btrfs_split_ordered_extent(): ASSERT(!(flags & ~BTRFS_ORDERED_TYPE_FLAGS)); because the BTRFS_ORDERED_IOERR flag is set and the definition of BTRFS_ORDERED_TYPE_FLAGS is just the union of all flags that identify the type of write (regular, nocow, prealloc, compressed, direct IO, encoded). Fix this by returning an error from btrfs_extract_ordered_extent() if we find the BTRFS_ORDERED_IOERR flag in the ordered extent. The error will be the error that resulted in the transaction abort or -EIO if no transaction abort happened. This was recently reported by syzbot with the following trace: FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 CPU: 0 UID: 0 PID: 5321 Comm: syz.0.0 Not tainted 6.13.0-rc5-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 fail_dump lib/fault-inject.c:53 [inline] should_fail_ex+0x3b0/0x4e0 lib/fault-inject.c:154 should_failslab+0xac/0x100 mm/failslab.c:46 slab_pre_alloc_hook mm/slub.c:4072 [inline] slab_alloc_node mm/slub.c:4148 [inline] __do_kmalloc_node mm/slub.c:4297 [inline] __kmalloc_noprof+0xdd/0x4c0 mm/slub.c:4310 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1037 [inline] btrfs_chunk_alloc_add_chunk_item+0x244/0x1100 fs/btrfs/volumes.c:5742 reserve_chunk_space+0x1ca/0x2c0 fs/btrfs/block-group.c:4292 check_system_chunk fs/btrfs/block-group.c:4319 [inline] do_chunk_alloc fs/btrfs/block-group.c:3891 [inline] btrfs_chunk_alloc+0x77b/0xf80 fs/btrfs/block-group.c:4187 find_free_extent_update_loop fs/btrfs/extent-tree.c:4166 [inline] find_free_extent+0x42d1/0x5810 fs/btrfs/extent-tree.c:4579 btrfs_reserve_extent+0x422/0x810 fs/btrfs/extent-tree.c:4672 btrfs_new_extent_direct fs/btrfs/direct-io.c:186 [inline] btrfs_get_blocks_direct_write+0x706/0xfa0 fs/btrfs/direct-io.c:321 btrfs_dio_iomap_begin+0xbb7/0x1180 fs/btrfs/direct-io.c:525 iomap_iter+0x697/0xf60 fs/iomap/iter.c:90 __iomap_dio_rw+0xeb9/0x25b0 fs/iomap/direct-io.c:702 btrfs_dio_write fs/btrfs/direct-io.c:775 [inline] btrfs_direct_write+0x610/0xa30 fs/btrfs/direct-io.c:880 btrfs_do_write_iter+0x2a0/0x760 fs/btrfs/file.c:1397 do_iter_readv_writev+0x600/0x880 vfs_writev+0x376/0xba0 fs/read_write.c:1050 do_pwritev fs/read_write.c:1146 [inline] __do_sys_pwritev2 fs/read_write.c:1204 [inline] __se_sys_pwritev2+0x196/0x2b0 fs/read_write.c:1195 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1281f85d29 RSP: 002b:00007f12819fe038 EFLAGS: 00000246 ORIG_RAX: 0000000000000148 RAX: ffffffffffffffda RBX: 00007f1282176080 RCX: 00007f1281f85d29 RDX: 0000000000000001 RSI: 0000000020000240 RDI: 0000000000000005 RBP: 00007f12819fe090 R08: 0000000000000000 R09: 0000000000000003 R10: 0000000000007000 R11: 0000000000000246 R12: 0000000000000002 R13: 0000000000000000 R14: 00007f1282176080 R15: 00007ffcb9e23328 </TASK> BTRFS error (device loop0 state A): Transaction aborted (error -12) BTRFS: error (device loop0 state A) in btrfs_chunk_alloc_add_chunk_item:5745: errno=-12 Out of memory BTRFS info (device loop0 state EA): forced readonly assertion failed: !(flags & ~BTRFS_ORDERED_TYPE_FLAGS), in fs/btrfs/ordered-data.c:1234 ------------[ cut here ]------------ kernel BUG at fs/btrfs/ordered-data.c:1234! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI CPU: 0 UID: 0 PID: 5321 Comm: syz.0.0 Not tainted 6.13.0-rc5-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:btrfs_split_ordered_extent+0xd8d/0xe20 fs/btrfs/ordered-data.c:1234 RSP: 0018:ffffc9000d1df2b8 EFLAGS: 00010246 RAX: 0000000000000057 RBX: 000000000006a000 RCX: 9ce21886c4195300 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: 0000000000000091 R08: ffffffff817f0a3c R09: 1ffff92001a3bdf4 R10: dffffc0000000000 R11: fffff52001a3bdf5 R12: 1ffff1100a45f401 R13: ffff8880522fa018 R14: dffffc0000000000 R15: 000000000006a000 FS: 00007f12819fe6c0(0000) GS:ffff88801fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000557750bd7da8 CR3: 00000000400ea000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> btrfs_extract_ordered_extent fs/btrfs/direct-io.c:702 [inline] btrfs_dio_submit_io+0x4be/0x6d0 fs/btrfs/direct-io.c:737 iomap_dio_submit_bio fs/iomap/direct-io.c:85 [inline] iomap_dio_bio_iter+0x1022/0x1740 fs/iomap/direct-io.c:447 __iomap_dio_rw+0x13b7/0x25b0 fs/iomap/direct-io.c:703 btrfs_dio_write fs/btrfs/direct-io.c:775 [inline] btrfs_direct_write+0x610/0xa30 fs/btrfs/direct-io.c:880 btrfs_do_write_iter+0x2a0/0x760 fs/btrfs/file.c:1397 do_iter_readv_writev+0x600/0x880 vfs_writev+0x376/0xba0 fs/read_write.c:1050 do_pwritev fs/read_write.c:1146 [inline] __do_sys_pwritev2 fs/read_write.c:1204 [inline] __se_sys_pwritev2+0x196/0x2b0 fs/read_write.c:1195 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1281f85d29 RSP: 002b:00007f12819fe038 EFLAGS: 00000246 ORIG_RAX: 0000000000000148 RAX: ffffffffffffffda RBX: 00007f1282176080 RCX: 00007f1281f85d29 RDX: 0000000000000001 RSI: 0000000020000240 RDI: 0000000000000005 RBP: 00007f12819fe090 R08: 0000000000000000 R09: 0000000000000003 R10: 0000000000007000 R11: 0000000000000246 R12: 0000000000000002 R13: 0000000000000000 R14: 00007f1282176080 R15: 00007ffcb9e23328 </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:btrfs_split_ordered_extent+0xd8d/0xe20 fs/btrfs/ordered-data.c:1234 RSP: 0018:ffffc9000d1df2b8 EFLAGS: 00010246 RAX: 0000000000000057 RBX: 000000000006a000 RCX: 9ce21886c4195300 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: 0000000000000091 R08: ffffffff817f0a3c R09: 1ffff92001a3bdf4 R10: dffffc0000000000 R11: fffff52001a3bdf5 R12: 1ffff1100a45f401 R13: ffff8880522fa018 R14: dffffc0000000000 R15: 000000000006a000 FS: 00007f12819fe6c0(0000) GS:ffff88801fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000557750bd7da8 CR3: 00000000400ea000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 In this case the transaction abort was due to (an injected) memory allocation failure when attempting to allocate a new chunk. Reported-by: syzbot+f60d8337a5c8e8d92a77@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/6777f2dd.050a0220.178762.0045.GAE@google.com/ Fixes: 52b1fdc ("btrfs: handle completed ordered extents in btrfs_split_ordered_extent") Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>

devm_platform_profile_register() expects a pointer to the private driver data but instead an address of the pointer variable is passed due to a typo. This leads to the crashes later: BUG: unable to handle page fault for address: 00000000fe0d0044 PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 6 UID: 0 PID: 1284 Comm: tuned Tainted: G W 6.13.0+ thesofproject#7 Tainted: [W]=WARN Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023 RIP: 0010:__mutex_lock.constprop.0+0x6bf/0x7f0 Call Trace: <TASK> dytc_profile_set+0x4a/0x140 [ideapad_laptop] _store_and_notify+0x13/0x40 [platform_profile] class_for_each_device+0x145/0x180 platform_profile_store+0xc0/0x130 [platform_profile] kernfs_fop_write_iter+0x13e/0x1f0 vfs_write+0x290/0x450 ksys_write+0x6c/0xe0 do_syscall_64+0x82/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e Found by Linux Verification Center (linuxtesting.org). Fixes: 249c576 ("ACPI: platform_profile: Let drivers set drvdata to the class device") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Reviewed-by: Kurt Borja <kuurtb@gmail.com> Link: https://lore.kernel.org/r/20250127210202.568691-1-pchelkin@ispras.ru Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

…faces Robert Morris created a test program which can cause usb_hub_to_struct_hub() to dereference a NULL or inappropriate pointer: Oops: general protection fault, probably for non-canonical address 0xcccccccccccccccc: 0000 [#1] SMP DEBUG_PAGEALLOC PTI CPU: 7 UID: 0 PID: 117 Comm: kworker/7:1 Not tainted 6.13.0-rc3-00017-gf44d154d6e3d thesofproject#14 Hardware name: FreeBSD BHYVE/BHYVE, BIOS 14.0 10/17/2021 Workqueue: usb_hub_wq hub_event RIP: 0010:usb_hub_adjust_deviceremovable+0x78/0x110 ... Call Trace: <TASK> ? die_addr+0x31/0x80 ? exc_general_protection+0x1b4/0x3c0 ? asm_exc_general_protection+0x26/0x30 ? usb_hub_adjust_deviceremovable+0x78/0x110 hub_probe+0x7c7/0xab0 usb_probe_interface+0x14b/0x350 really_probe+0xd0/0x2d0 ? __pfx___device_attach_driver+0x10/0x10 __driver_probe_device+0x6e/0x110 driver_probe_device+0x1a/0x90 __device_attach_driver+0x7e/0xc0 bus_for_each_drv+0x7f/0xd0 __device_attach+0xaa/0x1a0 bus_probe_device+0x8b/0xa0 device_add+0x62e/0x810 usb_set_configuration+0x65d/0x990 usb_generic_driver_probe+0x4b/0x70 usb_probe_device+0x36/0xd0 The cause of this error is that the device has two interfaces, and the hub driver binds to interface 1 instead of interface 0, which is where usb_hub_to_struct_hub() looks. We can prevent the problem from occurring by refusing to accept hub devices that violate the USB spec by having more than one configuration or interface. Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…t/tnguy/net-queue Tony Nguyen says: ==================== ice: fix Rx data path for heavy 9k MTU traffic Maciej Fijalkowski says: This patchset fixes a pretty nasty issue that was reported by RedHat folks which occurred after ~30 minutes (this value varied, just trying here to state that it was not observed immediately but rather after a considerable longer amount of time) when ice driver was tortured with jumbo frames via mix of iperf traffic executed simultaneously with wrk/nginx on client/server sides (HTTP and TCP workloads basically). The reported splats were spanning across all the bad things that can happen to the state of page - refcount underflow, use-after-free, etc. One of these looked as follows: [ 2084.019891] BUG: Bad page state in process swapper/34 pfn:97fcd0 [ 2084.025990] page:00000000a60ee772 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x97fcd0 [ 2084.035462] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ 2084.041990] raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000 [ 2084.049730] raw: 0000000000000000 0000000000000000 ffffffffffffffff 0000000000000000 [ 2084.057468] page dumped because: nonzero _refcount [ 2084.062260] Modules linked in: bonding tls sunrpc intel_rapl_msr intel_rapl_common intel_uncore_frequency intel_uncore_frequency_common i10nm_edac nfit libnvdimm x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm mgag200 irqd [ 2084.137829] CPU: 34 PID: 0 Comm: swapper/34 Kdump: loaded Not tainted 5.14.0-427.37.1.el9_4.x86_64 #1 [ 2084.147039] Hardware name: Dell Inc. PowerEdge R750/0216NK, BIOS 1.13.2 12/19/2023 [ 2084.154604] Call Trace: [ 2084.157058] <IRQ> [ 2084.159080] dump_stack_lvl+0x34/0x48 [ 2084.162752] bad_page.cold+0x63/0x94 [ 2084.166333] check_new_pages+0xb3/0xe0 [ 2084.170083] rmqueue_bulk+0x2d2/0x9e0 [ 2084.173749] ? ktime_get+0x35/0xa0 [ 2084.177159] rmqueue_pcplist+0x13b/0x210 [ 2084.181081] rmqueue+0x7d3/0xd40 [ 2084.184316] ? xas_load+0x9/0xa0 [ 2084.187547] ? xas_find+0x183/0x1d0 [ 2084.191041] ? xa_find_after+0xd0/0x130 [ 2084.194879] ? intel_iommu_iotlb_sync_map+0x89/0xe0 [ 2084.199759] get_page_from_freelist+0x11f/0x530 [ 2084.204291] __alloc_pages+0xf2/0x250 [ 2084.207958] ice_alloc_rx_bufs+0xcc/0x1c0 [ice] [ 2084.212543] ice_clean_rx_irq+0x631/0xa20 [ice] [ 2084.217111] ice_napi_poll+0xdf/0x2a0 [ice] [ 2084.221330] __napi_poll+0x27/0x170 [ 2084.224824] net_rx_action+0x233/0x2f0 [ 2084.228575] __do_softirq+0xc7/0x2ac [ 2084.232155] __irq_exit_rcu+0xa1/0xc0 [ 2084.235821] common_interrupt+0x80/0xa0 [ 2084.239662] </IRQ> [ 2084.241768] <TASK> The fix is mostly about reverting what was done in commit 1dc1a7e ("ice: Centrallize Rx buffer recycling") followed by proper timing on page_count() storage and then removing the ice_rx_buf::act related logic (which was mostly introduced for purposes from cited commit). Special thanks to Xu Du for providing reproducer and Jacob Keller for initial extensive analysis. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: stop storing XDP verdict within ice_rx_buf ice: gather page_count()'s of each frag right before XDP prog call ice: put Rx buffers after being done with current frame ==================== Link: https://patch.msgid.link/20250131185415.3741532-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Filesystems can write to disk from page reclaim with __GFP_FS set. Marc found a case where scsi_realloc_sdev_budget_map() ends up in page reclaim with GFP_KERNEL, where it could try to take filesystem locks again, leading to a deadlock. WARNING: possible circular locking dependency detected 6.13.0 #1 Not tainted ------------------------------------------------------ kswapd0/70 is trying to acquire lock: ffff8881025d5d78 (&q->q_usage_counter(io)){++++}-{0:0}, at: blk_mq_submit_bio+0x461/0x6e0 but task is already holding lock: ffffffff81ef5f40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x9f/0x760 The full lockdep splat can be found in Marc's report: https://lkml.org/lkml/2025/1/24/1101 Avoid the potential deadlock by doing the allocation with GFP_NOIO, which prevents both filesystem and block layer recursion. Reported-by: Marc Aurèle La France <tsi@tuyoix.net> Signed-off-by: Rik van Riel <riel@surriel.com> Link: https://lore.kernel.org/r/20250129104525.0ae8421e@fangorn Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Protected mode assumes that at minimum vgic-v3 is present, however KVM fails to actually enforce this at the time of initialization. As such, when running protected mode in a half-baked state on GICv2 hardware we see the hyp go belly up at vcpu_load() when it tries to restore the vgic-v3 cpuif: $ ./arch_timer_edge_cases [ 130.599140] kvm [4518]: nVHE hyp panic at: [<ffff800081102b58>] __kvm_nvhe___vgic_v3_restore_vmcr_aprs+0x8/0x84! [ 130.603685] kvm [4518]: Cannot dump pKVM nVHE stacktrace: !CONFIG_PROTECTED_NVHE_STACKTRACE [ 130.611962] kvm [4518]: Hyp Offset: 0xfffeca95ed000000 [ 130.617053] Kernel panic - not syncing: HYP panic: [ 130.617053] PS:800003c9 PC:0000b56a94102b58 ESR:0000000002000000 [ 130.617053] FAR:ffff00007b98d4d0 HPFAR:00000000007b98d0 PAR:0000000000000000 [ 130.617053] VCPU:0000000000000000 [ 130.638013] CPU: 0 UID: 0 PID: 4518 Comm: arch_timer_edge Tainted: G C 6.13.0-rc3-00009-gf7d03fcbf1f4 #1 [ 130.648790] Tainted: [C]=CRAP [ 130.651721] Hardware name: Libre Computer AML-S905X-CC (DT) [ 130.657242] Call trace: [ 130.659656] show_stack+0x18/0x24 (C) [ 130.663279] dump_stack_lvl+0x38/0x90 [ 130.666900] dump_stack+0x18/0x24 [ 130.670178] panic+0x388/0x3e8 [ 130.673196] nvhe_hyp_panic_handler+0x104/0x208 [ 130.677681] kvm_arch_vcpu_load+0x290/0x548 [ 130.681821] vcpu_load+0x50/0x80 [ 130.685013] kvm_arch_vcpu_ioctl_run+0x30/0x868 [ 130.689498] kvm_vcpu_ioctl+0x2e0/0x974 [ 130.693293] __arm64_sys_ioctl+0xb4/0xec [ 130.697174] invoke_syscall+0x48/0x110 [ 130.700883] el0_svc_common.constprop.0+0x40/0xe0 [ 130.705540] do_el0_svc+0x1c/0x28 [ 130.708818] el0_svc+0x30/0xd0 [ 130.711837] el0t_64_sync_handler+0x10c/0x138 [ 130.716149] el0t_64_sync+0x198/0x19c [ 130.719774] SMP: stopping secondary CPUs [ 130.723660] Kernel Offset: disabled [ 130.727103] CPU features: 0x000,00000800,02800000,0200421b [ 130.732537] Memory Limit: none [ 130.735561] ---[ end Kernel panic - not syncing: HYP panic: [ 130.735561] PS:800003c9 PC:0000b56a94102b58 ESR:0000000002000000 [ 130.735561] FAR:ffff00007b98d4d0 HPFAR:00000000007b98d0 PAR:0000000000000000 [ 130.735561] VCPU:0000000000000000 ]--- Fix it by failing KVM initialization if the system doesn't implement vgic-v3, as protected mode will never do anything useful on such hardware. Reported-by: Mark Brown <broonie@kernel.org> Closes: https://lore.kernel.org/kvmarm/5ca7588c-7bf2-4352-8661-e4a56a9cd9aa@sirena.org.uk/ Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20250203231543.233511-1-oliver.upton@linux.dev Signed-off-by: Marc Zyngier <maz@kernel.org>

…/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.14, take #1 - Correctly clean the BSS to the PoC before allowing EL2 to access it on nVHE/hVHE/protected configurations - Propagate ownership of debug registers in protected mode after the rework that landed in 6.14-rc1 - Stop pretending that we can run the protected mode without a GICv3 being present on the host - Fix a use-after-free situation that can occur if a vcpu fails to initialise the NV shadow S2 MMU contexts - Always evaluate the need to arm a background timer for fully emulated guest timers - Fix the emulation of EL1 timers in the absence of FEAT_ECV - Correctly handle the EL2 virtual timer, specially when HCR_EL2.E2H==0

commit c8347f9 ("gpu: host1x: Fix boot regression for Tegra") caused a use of uninitialized mutex leading to below warning when CONFIG_DEBUG_MUTEXES and CONFIG_DEBUG_LOCK_ALLOC are enabled. [ 41.662843] ------------[ cut here ]------------ [ 41.663012] DEBUG_LOCKS_WARN_ON(lock->magic != lock) [ 41.663035] WARNING: CPU: 4 PID: 794 at kernel/locking/mutex.c:587 __mutex_lock+0x670/0x878 [ 41.663458] Modules linked in: rtw88_8822c(+) bluetooth(+) rtw88_pci rtw88_core mac80211 aquantia libarc4 crc_itu_t cfg80211 tegra194_cpufreq dwmac_tegra(+) arm_dsu_pmu stmmac_platform stmmac pcs_xpcs rfkill at24 host1x(+) tegra_bpmp_thermal ramoops reed_solomon fuse loop nfnetlink xfs mmc_block rpmb_core ucsi_ccg ina3221 crct10dif_ce xhci_tegra ghash_ce lm90 sha2_ce sha256_arm64 sha1_ce sdhci_tegra pwm_fan sdhci_pltfm sdhci gpio_keys rtc_tegra cqhci mmc_core phy_tegra_xusb i2c_tegra tegra186_gpc_dma i2c_tegra_bpmp spi_tegra114 dm_mirror dm_region_hash dm_log dm_mod [ 41.665078] CPU: 4 UID: 0 PID: 794 Comm: (udev-worker) Not tainted 6.11.0-29.31_1538613708.el10.aarch64+debug #1 [ 41.665838] Hardware name: NVIDIA NVIDIA Jetson AGX Orin Developer Kit/Jetson, BIOS 36.3.0-gcid-35594366 02/26/2024 [ 41.672555] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 41.679636] pc : __mutex_lock+0x670/0x878 [ 41.683834] lr : __mutex_lock+0x670/0x878 [ 41.688035] sp : ffff800084b77090 [ 41.691446] x29: ffff800084b77160 x28: ffffdd4bebf7b000 x27: ffffdd4be96b1000 [ 41.698799] x26: 1fffe0002308361c x25: 1ffff0001096ee18 x24: 0000000000000000 [ 41.706149] x23: 0000000000000000 x22: 0000000000000002 x21: ffffdd4be6e3c7a0 [ 41.713500] x20: ffff800084b770f0 x19: ffff00011841b1e8 x18: 0000000000000000 [ 41.720675] x17: 0000000000000000 x16: 0000000000000000 x15: 0720072007200720 [ 41.728023] x14: 0000000000000000 x13: 0000000000000001 x12: ffff6001a96eaab3 [ 41.735375] x11: 1fffe001a96eaab2 x10: ffff6001a96eaab2 x9 : ffffdd4be4838bbc [ 41.742723] x8 : 00009ffe5691554e x7 : ffff000d4b755593 x6 : 0000000000000001 [ 41.749985] x5 : ffff000d4b755590 x4 : 1fffe0001d88f001 x3 : dfff800000000000 [ 41.756988] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0000ec478000 [ 41.764251] Call trace: [ 41.766695] __mutex_lock+0x670/0x878 [ 41.770373] mutex_lock_nested+0x2c/0x40 [ 41.774134] host1x_intr_start+0x54/0xf8 [host1x] [ 41.778863] host1x_runtime_resume+0x150/0x228 [host1x] [ 41.783935] pm_generic_runtime_resume+0x84/0xc8 [ 41.788485] __rpm_callback+0xa0/0x478 [ 41.792422] rpm_callback+0x15c/0x1a8 [ 41.795922] rpm_resume+0x698/0xc08 [ 41.799597] __pm_runtime_resume+0xa8/0x140 [ 41.803621] host1x_probe+0x810/0xbc0 [host1x] [ 41.807909] platform_probe+0xcc/0x1a8 [ 41.811845] really_probe+0x188/0x800 [ 41.815347] __driver_probe_device+0x164/0x360 [ 41.819810] driver_probe_device+0x64/0x1a8 [ 41.823834] __driver_attach+0x180/0x490 [ 41.827773] bus_for_each_dev+0x104/0x1a0 [ 41.831797] driver_attach+0x44/0x68 [ 41.835296] bus_add_driver+0x23c/0x4e8 [ 41.839235] driver_register+0x15c/0x3a8 [ 41.843170] __platform_register_drivers+0xa4/0x208 [ 41.848159] tegra_host1x_init+0x4c/0xff8 [host1x] [ 41.853147] do_one_initcall+0xd4/0x380 [ 41.856997] do_init_module+0x1dc/0x698 [ 41.860758] load_module+0xc70/0x1300 [ 41.864435] __do_sys_init_module+0x1a8/0x1d0 [ 41.868721] __arm64_sys_init_module+0x74/0xb0 [ 41.873183] invoke_syscall.constprop.0+0xdc/0x1e8 [ 41.877997] do_el0_svc+0x154/0x1d0 [ 41.881671] el0_svc+0x54/0x140 [ 41.884820] el0t_64_sync_handler+0x120/0x130 [ 41.889285] el0t_64_sync+0x1a4/0x1a8 [ 41.892960] irq event stamp: 69737 [ 41.896370] hardirqs last enabled at (69737): [<ffffdd4be6d7768c>] _raw_spin_unlock_irqrestore+0x44/0xe8 [ 41.905739] hardirqs last disabled at (69736): [<ffffdd4be59dcd40>] clk_enable_lock+0x98/0x198 [ 41.914314] softirqs last enabled at (68082): [<ffffdd4be466b1d0>] handle_softirqs+0x4c8/0x890 [ 41.922977] softirqs last disabled at (67945): [<ffffdd4be44f02a4>] __do_softirq+0x1c/0x28 [ 41.931289] ---[ end trace 0000000000000000 ]--- Inside the probe function when pm_runtime_enable() is called, the PM core invokes a resume callback if the device Host1x is in a suspended state. As it can be seen in the logs above, this leads to host1x_intr_start() function call which is trying to acquire a mutex lock. But, the function host_intr_init() only gets called after the pm_runtime_enable() where mutex is initialised leading to the use of mutex prior to its initialisation. Fix this by moving the mutex initialisation prior to the runtime PM enablement function pm_runtime_enable() in probe. Fixes: c8347f9 ("gpu: host1x: Fix boot regression for Tegra") Signed-off-by: Rupinderjit Singh <rusingh@redhat.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Link: https://patchwork.ozlabs.org/project/linux-tegra/patch/20250206155803.201942-1-rusingh@redhat.com/

vxlan_init() must check vxlan_vnigroup_init() success otherwise a crash happens later, spotted by syzbot. Oops: general protection fault, probably for non-canonical address 0xdffffc000000002c: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000160-0x0000000000000167] CPU: 0 UID: 0 PID: 7313 Comm: syz-executor147 Not tainted 6.14.0-rc1-syzkaller-00276-g69b54314c975 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:vxlan_vnigroup_uninit+0x89/0x500 drivers/net/vxlan/vxlan_vnifilter.c:912 Code: 00 48 8b 44 24 08 4c 8b b0 98 41 00 00 49 8d 86 60 01 00 00 48 89 c2 48 89 44 24 10 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 4d 04 00 00 49 8b 86 60 01 00 00 48 ba 00 00 00 RSP: 0018:ffffc9000cc1eea8 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000001 RCX: ffffffff8672effb RDX: 000000000000002c RSI: ffffffff8672ecb9 RDI: ffff8880461b4f18 RBP: ffff8880461b4ef4 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000020000 R13: ffff8880461b0d80 R14: 0000000000000000 R15: dffffc0000000000 FS: 00007fecfa95d6c0(0000) GS:ffff88806a600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fecfa95cfb8 CR3: 000000004472c000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> vxlan_uninit+0x1ab/0x200 drivers/net/vxlan/vxlan_core.c:2942 unregister_netdevice_many_notify+0x12d6/0x1f30 net/core/dev.c:11824 unregister_netdevice_many net/core/dev.c:11866 [inline] unregister_netdevice_queue+0x307/0x3f0 net/core/dev.c:11736 register_netdevice+0x1829/0x1eb0 net/core/dev.c:10901 __vxlan_dev_create+0x7c6/0xa30 drivers/net/vxlan/vxlan_core.c:3981 vxlan_newlink+0xd1/0x130 drivers/net/vxlan/vxlan_core.c:4407 rtnl_newlink_create net/core/rtnetlink.c:3795 [inline] __rtnl_newlink net/core/rtnetlink.c:3906 [inline] Fixes: f9c4bb0 ("vxlan: vni filtering support on collect metadata device") Reported-by: syzbot+6a9624592218c2c5e7aa@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/67a9d9b4.050a0220.110943.002d.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Roopa Prabhu <roopa@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20250210105242.883482-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

bch2_nocow_write_convert_unwritten is already in transaction context: 00191 ========= TEST generic/648 00242 kernel BUG at fs/bcachefs/btree_iter.c:3332! 00242 Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP 00242 Modules linked in: 00242 CPU: 4 UID: 0 PID: 2593 Comm: fsstress Not tainted 6.13.0-rc3-ktest-g345af8f855b7 #14403 00242 Hardware name: linux,dummy-virt (DT) 00242 pstate: 60001005 (nZCv daif -PAN -UAO -TCO -DIT +SSBS BTYPE=--) 00242 pc : __bch2_trans_get+0x120/0x410 00242 lr : __bch2_trans_get+0xcc/0x410 00242 sp : ffffff80d89af600 00242 x29: ffffff80d89af600 x28: ffffff80ddb23000 x27: 00000000fffff705 00242 x26: ffffff80ddb23028 x25: ffffff80d8903fe0 x24: ffffff80ebb30168 00242 x23: ffffff80c8aeb500 x22: 000000000000005d x21: ffffff80d8904078 00242 x20: ffffff80d8900000 x19: ffffff80da9e8000 x18: 0000000000000000 00242 x17: 64747568735f6c61 x16: 6e72756f6a20726f x15: 0000000000000028 00242 x14: 0000000000000004 x13: 000000000000f787 x12: ffffffc081bbcdc8 00242 x11: 0000000000000000 x10: 0000000000000003 x9 : ffffffc08094efbc 00242 x8 : 000000001092c111 x7 : 000000000000000c x6 : ffffffc083c31fc4 00242 x5 : ffffffc083c31f28 x4 : ffffff80c8aeb500 x3 : ffffff80ebb30000 00242 x2 : 0000000000000001 x1 : 0000000000000a21 x0 : 000000000000028e 00242 Call trace: 00242 __bch2_trans_get+0x120/0x410 (P) 00242 bch2_inum_offset_err_msg+0x48/0xb0 00242 bch2_nocow_write_convert_unwritten+0x3d0/0x530 00242 bch2_nocow_write+0xeb0/0x1000 00242 __bch2_write+0x330/0x4e8 00242 bch2_write+0x1f0/0x530 00242 bch2_direct_write+0x530/0xc00 00242 bch2_write_iter+0x160/0xbe0 00242 vfs_write+0x1cc/0x360 00242 ksys_write+0x5c/0xf0 00242 __arm64_sys_write+0x20/0x30 00242 invoke_syscall.constprop.0+0x54/0xe8 00242 do_el0_svc+0x44/0xc0 00242 el0_svc+0x34/0xa0 00242 el0t_64_sync_handler+0x104/0x130 00242 el0t_64_sync+0x154/0x158 00242 Code: 6b01001f 54ffff01 79408460 3617fec0 (d4210000) 00242 ---[ end trace 0000000000000000 ]--- 00242 Kernel panic - not syncing: Oops - BUG: Fatal exception Signed-off-by: Alan Huang <mmpgouride@gmail.com> Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

We have several places across the kernel where we want to access another task's syscall arguments, such as ptrace(2), seccomp(2), etc., by making a call to syscall_get_arguments(). This works for register arguments right away by accessing the task's `regs' member of `struct pt_regs', however for stack arguments seen with 32-bit/o32 kernels things are more complicated. Technically they ought to be obtained from the user stack with calls to an access_remote_vm(), but we have an easier way available already. So as to be able to access syscall stack arguments as regular function arguments following the MIPS calling convention we copy them over from the user stack to the kernel stack in arch/mips/kernel/scall32-o32.S, in handle_sys(), to the current stack frame's outgoing argument space at the top of the stack, which is where the handler called expects to see its incoming arguments. This area is also pointed at by the `pt_regs' pointer obtained by task_pt_regs(). Make the o32 stack argument space a proper member of `struct pt_regs' then, by renaming the existing member from `pad0' to `args' and using generated offsets to access the space. No functional change though. With the change in place the o32 kernel stack frame layout at the entry to a syscall handler invoked by handle_sys() is therefore as follows: $sp + 68 -> | ... | <- pt_regs.regs[9] +---------------------+ $sp + 64 -> | $t0 | <- pt_regs.regs[8] +---------------------+ $sp + 60 -> | $a3/argument #4 | <- pt_regs.regs[7] +---------------------+ $sp + 56 -> | $a2/argument #3 | <- pt_regs.regs[6] +---------------------+ $sp + 52 -> | $a1/argument #2 | <- pt_regs.regs[5] +---------------------+ $sp + 48 -> | $a0/argument #1 | <- pt_regs.regs[4] +---------------------+ $sp + 44 -> | $v1 | <- pt_regs.regs[3] +---------------------+ $sp + 40 -> | $v0 | <- pt_regs.regs[2] +---------------------+ $sp + 36 -> | $at | <- pt_regs.regs[1] +---------------------+ $sp + 32 -> | $zero | <- pt_regs.regs[0] +---------------------+ $sp + 28 -> | stack argument thesofproject#8 | <- pt_regs.args[7] +---------------------+ $sp + 24 -> | stack argument thesofproject#7 | <- pt_regs.args[6] +---------------------+ $sp + 20 -> | stack argument thesofproject#6 | <- pt_regs.args[5] +---------------------+ $sp + 16 -> | stack argument thesofproject#5 | <- pt_regs.args[4] +---------------------+ $sp + 12 -> | psABI space for $a3 | <- pt_regs.args[3] +---------------------+ $sp + 8 -> | psABI space for $a2 | <- pt_regs.args[2] +---------------------+ $sp + 4 -> | psABI space for $a1 | <- pt_regs.args[1] +---------------------+ $sp + 0 -> | psABI space for $a0 | <- pt_regs.args[0] +---------------------+ holding user data received and with the first 4 frame slots reserved by the psABI for the compiler to spill the incoming arguments from $a0-$a3 registers (which it sometimes does according to its needs) and the next 4 frame slots designated by the psABI for any stack function arguments that follow. This data is also available for other tasks to peek/poke at as reqired and where permitted. Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

This makes ptrace/get_syscall_info selftest pass on mips o32 and mips64 o32 by fixing the following two test assertions: 1. get_syscall_info test assertion on mips o32: # get_syscall_info.c:218:get_syscall_info:Expected exp_args[5] (3134521044) == info.entry.args[4] (4911432) # get_syscall_info.c:219:get_syscall_info:wait #1: entry stop mismatch 2. get_syscall_info test assertion on mips64 o32: # get_syscall_info.c:209:get_syscall_info:Expected exp_args[2] (3134324433) == info.entry.args[1] (18446744072548908753) # get_syscall_info.c:210:get_syscall_info:wait #1: entry stop mismatch The first assertion happens due to mips_get_syscall_arg() trying to access another task's context but failing to do it properly because get_user() it calls just peeks at the current task's context. It usually does not crash because the default user stack always gets assigned the same VMA, but it is pure luck which mips_get_syscall_arg() wouldn't have if e.g. the stack was switched (via setcontext(3) or however) or a non-default process's thread peeked at, and in any case irrelevant data is obtained just as observed with the test case. mips_get_syscall_arg() ought to be using access_remote_vm() instead to retrieve the other task's stack contents, but given that the data has been already obtained and saved in `struct pt_regs' it would be an overkill. The first assertion is fixed for mips o32 by using struct pt_regs.args instead of get_user() to obtain syscall arguments. This approach works due to this piece in arch/mips/kernel/scall32-o32.S: /* * Ok, copy the args from the luser stack to the kernel stack. */ .set push .set noreorder .set nomacro load_a4: user_lw(t5, 16(t0)) # argument thesofproject#5 from usp load_a5: user_lw(t6, 20(t0)) # argument thesofproject#6 from usp load_a6: user_lw(t7, 24(t0)) # argument thesofproject#7 from usp load_a7: user_lw(t8, 28(t0)) # argument thesofproject#8 from usp loads_done: sw t5, PT_ARG4(sp) # argument thesofproject#5 to ksp sw t6, PT_ARG5(sp) # argument thesofproject#6 to ksp sw t7, PT_ARG6(sp) # argument thesofproject#7 to ksp sw t8, PT_ARG7(sp) # argument thesofproject#8 to ksp .set pop .section __ex_table,"a" PTR_WD load_a4, bad_stack_a4 PTR_WD load_a5, bad_stack_a5 PTR_WD load_a6, bad_stack_a6 PTR_WD load_a7, bad_stack_a7 .previous arch/mips/kernel/scall64-o32.S has analogous code for mips64 o32 that allows fixing the issue by obtaining syscall arguments from struct pt_regs.regs[4..11] instead of the erroneous use of get_user(). The second assertion is fixed by truncating 64-bit values to 32-bit syscall arguments. Fixes: c0ff3c5 ("MIPS: Enable HAVE_ARCH_TRACEHOOK.") Signed-off-by: Dmitry V. Levin <ldv@strace.io> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

This fixes the following trace by reworking the locking of l2cap_conn so instead of only locking when changing the chan_l list this promotes chan_lock to a general lock of l2cap_conn so whenever it is being held it would prevents the likes of l2cap_conn_del to run: list_del corruption, ffff888021297e00->prev is LIST_POISON2 (dead000000000122) ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:61! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 UID: 0 PID: 5896 Comm: syz-executor213 Not tainted 6.14.0-rc1-next-20250204-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 12/27/2024 RIP: 0010:__list_del_entry_valid_or_report+0x12c/0x190 lib/list_debug.c:59 Code: 8c 4c 89 fe 48 89 da e8 32 8c 37 fc 90 0f 0b 48 89 df e8 27 9f 14 fd 48 c7 c7 a0 c0 60 8c 4c 89 fe 48 89 da e8 15 8c 37 fc 90 <0f> 0b 4c 89 e7 e8 0a 9f 14 fd 42 80 3c 2b 00 74 08 4c 89 e7 e8 cb RSP: 0018:ffffc90003f6f998 EFLAGS: 00010246 RAX: 000000000000004e RBX: dead000000000122 RCX: 01454d423f7fbf00 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: dffffc0000000000 R08: ffffffff819f077c R09: 1ffff920007eded0 R10: dffffc0000000000 R11: fffff520007eded1 R12: dead000000000122 R13: dffffc0000000000 R14: ffff8880352248d8 R15: ffff888021297e00 FS: 00007f7ace6686c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7aceeeb1d0 CR3: 000000003527c000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __list_del_entry_valid include/linux/list.h:124 [inline] __list_del_entry include/linux/list.h:215 [inline] list_del_rcu include/linux/rculist.h:168 [inline] hci_chan_del+0x70/0x1b0 net/bluetooth/hci_conn.c:2858 l2cap_conn_free net/bluetooth/l2cap_core.c:1816 [inline] kref_put include/linux/kref.h:65 [inline] l2cap_conn_put+0x70/0xe0 net/bluetooth/l2cap_core.c:1830 l2cap_sock_shutdown+0xa8a/0x1020 net/bluetooth/l2cap_sock.c:1377 l2cap_sock_release+0x79/0x1d0 net/bluetooth/l2cap_sock.c:1416 __sock_release net/socket.c:642 [inline] sock_close+0xbc/0x240 net/socket.c:1393 __fput+0x3e9/0x9f0 fs/file_table.c:448 task_work_run+0x24f/0x310 kernel/task_work.c:227 ptrace_notify+0x2d2/0x380 kernel/signal.c:2522 ptrace_report_syscall include/linux/ptrace.h:415 [inline] ptrace_report_syscall_exit include/linux/ptrace.h:477 [inline] syscall_exit_work+0xc7/0x1d0 kernel/entry/common.c:173 syscall_exit_to_user_mode_prepare kernel/entry/common.c:200 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:205 [inline] syscall_exit_to_user_mode+0x24a/0x340 kernel/entry/common.c:218 do_syscall_64+0x100/0x230 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f7aceeaf449 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 41 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f7ace668218 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: fffffffffffffffc RBX: 00007f7acef39328 RCX: 00007f7aceeaf449 RDX: 000000000000000e RSI: 0000000020000100 RDI: 0000000000000004 RBP: 00007f7acef39320 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000003 R13: 0000000000000004 R14: 00007f7ace668670 R15: 000000000000000b </TASK> Modules linked in: ---[ end trace 0000000000000000 ]--- RIP: 0010:__list_del_entry_valid_or_report+0x12c/0x190 lib/list_debug.c:59 Code: 8c 4c 89 fe 48 89 da e8 32 8c 37 fc 90 0f 0b 48 89 df e8 27 9f 14 fd 48 c7 c7 a0 c0 60 8c 4c 89 fe 48 89 da e8 15 8c 37 fc 90 <0f> 0b 4c 89 e7 e8 0a 9f 14 fd 42 80 3c 2b 00 74 08 4c 89 e7 e8 cb RSP: 0018:ffffc90003f6f998 EFLAGS: 00010246 RAX: 000000000000004e RBX: dead000000000122 RCX: 01454d423f7fbf00 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: dffffc0000000000 R08: ffffffff819f077c R09: 1ffff920007eded0 R10: dffffc0000000000 R11: fffff520007eded1 R12: dead000000000122 R13: dffffc0000000000 R14: ffff8880352248d8 R15: ffff888021297e00 FS: 00007f7ace6686c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7acef05b08 CR3: 000000003527c000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Reported-by: syzbot+10bd8fe6741eedd2be2e@syzkaller.appspotmail.com Tested-by: syzbot+10bd8fe6741eedd2be2e@syzkaller.appspotmail.com Fixes: b4f82f9 ("Bluetooth: L2CAP: Fix slab-use-after-free Read in l2cap_send_cmd") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>

The behaviour of kthread_create_worker() was recently changed to align with the one of kthread_create(). The kthread worker is created but not awaken by default. This is to allow the use of kthread_affine_preferred() and kthread_bind[_mask]() with kthread workers. In order to keep the old behaviour and wake the kthread up, kthread_run_worker() must be used. All the pre-existing users have been converted, except for UVC that was introduced in the same merge window as the API change. This results in hangs: INFO: task UVCG:82 blocked for more than 491 seconds. Tainted: G T 6.13.0-rc2-00014-gb04e317b5226 #1 task:UVCG state:D stack:0 pid:82 Call Trace: __schedule schedule schedule_preempt_disabled kthread ? kthread_flush_work ret_from_fork ret_from_fork_asm entry_INT80_32 Fix this with converting UVCG kworker to the new API. Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202502121025.55bfa801-lkp@intel.com Fixes: f0bbfbd ("usb: gadget: uvc: rework to enqueue in pump worker from encoded queue") Cc: stable <stable@kernel.org> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lore.kernel.org/r/20250212135514.30539-1-frederic@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When trying to mmap a trace instance buffer that is attached to reserve_mem, it would crash: BUG: unable to handle page fault for address: ffffe97bd00025c8 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 2862f3067 P4D 2862f3067 PUD 0 Oops: Oops: 0000 [#1] PREEMPT_RT SMP PTI CPU: 4 UID: 0 PID: 981 Comm: mmap-rb Not tainted 6.14.0-rc2-test-00003-g7f1a5e3fbf9e-dirty thesofproject#233 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:validate_page_before_insert+0x5/0xb0 Code: e2 01 89 d0 c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 <48> 8b 46 08 a8 01 75 67 66 90 48 89 f0 8b 50 34 85 d2 74 76 48 89 RSP: 0018:ffffb148c2f3f968 EFLAGS: 00010246 RAX: ffff9fa5d3322000 RBX: ffff9fa5ccff9c08 RCX: 00000000b879ed29 RDX: ffffe97bd00025c0 RSI: ffffe97bd00025c0 RDI: ffff9fa5ccff9c08 RBP: ffffb148c2f3f9f0 R08: 0000000000000004 R09: 0000000000000004 R10: 0000000000000000 R11: 0000000000000200 R12: 0000000000000000 R13: 00007f16a18d5000 R14: ffff9fa5c48db6a8 R15: 0000000000000000 FS: 00007f16a1b54740(0000) GS:ffff9fa73df00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffe97bd00025c8 CR3: 00000001048c6006 CR4: 0000000000172ef0 Call Trace: <TASK> ? __die_body.cold+0x19/0x1f ? __die+0x2e/0x40 ? page_fault_oops+0x157/0x2b0 ? search_module_extables+0x53/0x80 ? validate_page_before_insert+0x5/0xb0 ? kernelmode_fixup_or_oops.isra.0+0x5f/0x70 ? __bad_area_nosemaphore+0x16e/0x1b0 ? bad_area_nosemaphore+0x16/0x20 ? do_kern_addr_fault+0x77/0x90 ? exc_page_fault+0x22b/0x230 ? asm_exc_page_fault+0x2b/0x30 ? validate_page_before_insert+0x5/0xb0 ? vm_insert_pages+0x151/0x400 __rb_map_vma+0x21f/0x3f0 ring_buffer_map+0x21b/0x2f0 tracing_buffers_mmap+0x70/0xd0 __mmap_region+0x6f0/0xbd0 mmap_region+0x7f/0x130 do_mmap+0x475/0x610 vm_mmap_pgoff+0xf2/0x1d0 ksys_mmap_pgoff+0x166/0x200 __x64_sys_mmap+0x37/0x50 x64_sys_call+0x1670/0x1d70 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f The reason was that the code that maps the ring buffer pages to user space has: page = virt_to_page((void *)cpu_buffer->subbuf_ids[s]); And uses that in: vm_insert_pages(vma, vma->vm_start, pages, &nr_pages); But virt_to_page() does not work with vmap()'d memory which is what the persistent ring buffer has. It is rather trivial to allow this, but for now just disable mmap() of instances that have their ring buffer from the reserve_mem option. If an mmap() is performed on a persistent buffer it will return -ENODEV just like it would if the .mmap field wasn't defined in the file_operations structure. Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Link: https://lore.kernel.org/20250214115547.0d7287d3@gandalf.local.home Fixes: 9b7bdf6 ("tracing: Have trace_printk not use binary prints if boot buffer") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

singalsu and others added 22 commits September 7, 2018 09:39

ASoC: dapm: fix kcontrols for effect widgets

aa9b276

This patch adds the handling of snd_soc_dapm_effect that was missing. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

SOF: Increase DSP maximum IPC size to 384

fcb87ed

This patch updates the maximum size into the same as used currently in DSP side. Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

SOF: Update EQ IPC header file

f0cc5ea

This patch updates the definitions and structs to indentical as used on DSP side. It will help using the equalizer setup blobs in user space. Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

sof: add a check for the IRQ GPIO level

0f9af23

Checking for the IRQ GPIO level once an IRQ has been triggered shouldn't be necessary, once an IRQ has been triggered, so this might end up being superfluous. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

rpi: temporarily disable SOF DT

9f93a3a

The SOF DT doesn't compile yet, it's only provided as an example, disable it for now to prevent automated builds from failing. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

Revert "sof: fix compilation on non X86 platforms"

2170a56

This reverts commit 41b8f5d and fixes #113. Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>

ASoC:topology:delete dynamic object during widget remove

64cf3e3

remove the dynamic object during the topology free stage. to avoid multi remove operation. Signed-off-by: Wu Zhigang <zhigang.wu@linux.intel.com>

ASoC: SOF: restore byte control data after resume

ae5f868

This patch adds support for retreiving byte control data after the DSP comes out of D3. Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>

ASoC: SOF: Kconfig: add an item to force IPC position update for debug

b0266de

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: Intel: add no_ipc_position flag for position update

09bb006

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: add pointer callback for dsp_ops

d582fbe

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: Intel: correct period settings for hdac_stream

3e80cfb

pcm_runtime is not ready yet at hw_params() stage, so we need to retrieve period settings from params here. Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: apl: add pcm_pointer callback to dsp_ops

540aea4

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: only elapse/inform ALSA for irq mode

a224ab2

Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>

ASoC: SOF: skl enable the skl/kbl ops, instead of using apl_ops v2

50792bc

Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>

bardliao merged this pull request into bardliao:topic/sof-dev Sep 17, 2018

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

merge from thesofproject #1

merge from thesofproject #1

bardliao commented Sep 17, 2018

merge from thesofproject #1

merge from thesofproject #1

Conversation

bardliao commented Sep 17, 2018