NI DAQMX Trigger Attributes

Trigger Attributes

Start
Reference
More
Advanced
- DAQmx_Trigger_SyncType

Start

DAQmx_StartTrig_Type

Data Type:	int32
Description:	Specifies the type of trigger to use to start a task.

Valid values

DAQmx_Val_AnlgEdge	10099	Trigger when an analog signal signal crosses a threshold.
DAQmx_Val_AnlgMultiEdge	16108	Trigger when any of the configured analog signals cross their respective thresholds.
DAQmx_Val_DigEdge	10150	Trigger on the rising or falling edge of a digital signal.
DAQmx_Val_DigPattern	10398	Trigger when digital physical channels match a digital pattern.
DAQmx_Val_AnlgWin	10103	Trigger when an analog signal enters or leaves a range of values. The range is in the units of the measurement.
DAQmx_Val_Time	15996	Trigger when a specified time is reached.
DAQmx_Val_None	10230	Disable triggering for the task.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_Term

Data Type:	char*
Description:	Indicates the name of the internal Start Trigger terminal for the task. This property does not return the name of the trigger source terminal.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Start Digital Edge

DAQmx_DigEdge_StartTrig_Src

Data Type:	char*
Description:	Specifies the name of a terminal where there is a digital signal to use as the source of the Start Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_StartTrig_Edge

Data Type:	int32
Description:	Specifies on which edge of a digital pulse to start acquiring or generating samples.

Valid values

DAQmx_Val_Rising	10280	Rising edge(s).
DAQmx_Val_Falling	10171	Falling edge(s).

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Digital Edge Digital Filter

DAQmx_DigEdge_StartTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the trigger signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_StartTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Digital Edge Timebase

DAQmx_DigEdge_StartTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the input terminal of the signal to use as the timebase of the pulse width filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_StartTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the pulse width filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Digital Edge Digital Synchronization

DAQmx_DigEdge_StartTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device. If you set this property to TRUE, the device does not recognize and act upon the trigger until the next pulse of the internal timebase.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Digital Pattern

DAQmx_DigPattern_StartTrig_Src

Data Type:	char*
Description:	Specifies the physical channels to use for pattern matching. The order of the physical channels determines the order of the pattern. If a port is included, the order of the physical channels within the port is in ascending order.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_StartTrig_Pattern

Data Type:	char*
Description:	Specifies the digital pattern that must be met for the Start Trigger to occur.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_StartTrig_When

Data Type:	int32
Description:	Specifies whether the Start Trigger occurs when the physical channels specified with DAQmx_DigPattern_StartTrig_Src match or differ from the digital pattern specified with DAQmx_DigPattern_StartTrig_Pattern.

Valid values

DAQmx_Val_PatternMatches	10254	Trigger when the physical channels match the specified pattern.
DAQmx_Val_PatternDoesNotMatch	10253	Trigger when the physical channels do not match the specified pattern.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Edge

DAQmx_AnlgEdge_StartTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the Start Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_Slope

Data Type:	int32
Description:	Specifies on which slope of the trigger signal to start acquiring or generating samples.

Valid values

DAQmx_Val_RisingSlope	10280	Trigger on the rising slope of the signal.
DAQmx_Val_FallingSlope	10171	Trigger on the falling slope of the signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_Lvl

Data Type:	float64
Description:	Specifies at what threshold in the units of the measurement or generation to start acquiring or generating samples. Use DAQmx_AnlgEdge_StartTrig_Slope to specify on which slope to trigger on this threshold.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_Hyst

Data Type:	float64
Description:	Specifies a hysteresis level in the units of the measurement or generation. If DAQmx_AnlgEdge_StartTrig_Slope is DAQmx_Val_RisingSlope, the trigger does not deassert until the source signal passes below DAQmx_AnlgEdge_StartTrig_Lvl minus the hysteresis. If DAQmx_AnlgEdge_StartTrig_Slope is DAQmx_Val_FallingSlope, the trigger does not deassert until the source signal passes above DAQmx_AnlgEdge_StartTrig_Lvl plus the hysteresis. Hysteresis is always enabled. Set this property to a non-zero value to use hysteresis.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Edge Digital Filter

DAQmx_AnlgEdge_StartTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay above or below the trigger level for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the hysteresis window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Edge Timebase

DAQmx_AnlgEdge_StartTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_StartTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Edge Digital Synchronization

DAQmx_AnlgEdge_StartTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Multiple Edge

DAQmx_AnlgMultiEdge_StartTrig_Srcs

Data Type:	char*
Description:	Specifies a list and/or range of analog sources that are going to be used for Analog triggering. Each source corresponds to an element in each of the Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_StartTrig_Slopes

Data Type:	int32*
Description:	Specifies an array of slopes on which to trigger task to start generating or acquiring samples. Each element of the array corresponds to a source in Start.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

Valid values

DAQmx_Val_RisingSlope	10280	Trigger on the rising slope of the signal.
DAQmx_Val_FallingSlope	10171	Trigger on the falling slope of the signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_StartTrig_Lvls

Data Type:	float64*
Description:	Specifies an array of thresholds in the units of the measurement or generation to start acquiring or generating samples. Each element of the array corresponds to a source in Start.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_StartTrig_Hysts

Data Type:	float64*
Description:	Specifies an array of hysteresis levels in the units of the measurement or generation. If the corresponding element of Start.AnlgMultiEdge.Slopes is Rising, the trigger does not deassert until the source signal passes below the corresponding element of Start.AnlgMultiEdge.Lvls minus the hysteresis. If Start.AnlgEdge.Slope is Falling, the trigger does not deassert until the source signal passes above Start.AnlgEdge.Lvl plus the hysteresis. Hysteresis is always enabled. Set this property to a non-zero value to use hysteresis. Each element of the array corresponds to a source in Start.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_StartTrig_Couplings

Data Type:	int32*
Description:	Specifies an array that describes the couplings for the corresponding source signal of the trigger if the source is a terminal rather than a virtual channel. Each element of the array corresponds to a source in Start.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Window

DAQmx_AnlgWin_StartTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the Start Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_When

Data Type:	int32
Description:	Specifies whether the task starts acquiring or generating samples when the signal enters or leaves the window you specify with DAQmx_AnlgWin_StartTrig_Btm and DAQmx_AnlgWin_StartTrig_Top.

Valid values

DAQmx_Val_EnteringWin	10163	Trigger when the signal enters the window.
DAQmx_Val_LeavingWin	10208	Trigger when the signal leaves the window.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_Top

Data Type:	float64
Description:	Specifies the upper limit of the window. Specify this value in the units of the measurement or generation.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_Btm

Data Type:	float64
Description:	Specifies the lower limit of the window. Specify this value in the units of the measurement or generation.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Window Digital Filter

DAQmx_AnlgWin_StartTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay within the trigger window for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Window Timebase

DAQmx_AnlgWin_StartTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_StartTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Analog Window Digital Synchronization

DAQmx_AnlgWin_StartTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Time

DAQmx_StartTrig_TrigWhen

Data Type:	CVIAbsoluteTime
Description:	Specifies when to trigger the start trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_Timescale

Data Type:	int32
Description:	Specifies the timescale to be used for timestamps used in a time trigger.

Valid values

DAQmx_Val_HostTime	16126	Use the host device.
DAQmx_Val_IODeviceTime	16127	Use the I/O device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Start Timestamp

DAQmx_StartTrig_TimestampEnable

Data Type:	bool32
Description:	Specifies whether the start trigger timestamp is enabled. If the timestamp is enabled but no resources are available, an error will be returned at run time.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_TimestampTimescale

Data Type:	int32
Description:	Specifies the start trigger timestamp timescale.

Valid values

DAQmx_Val_HostTime	16126	Use the host device.
DAQmx_Val_IODeviceTime	16127	Use the I/O device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_TimestampVal

Data Type:	CVIAbsoluteTime
Description:	Indicates the start trigger timestamp value.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Start More

DAQmx_StartTrig_Delay

Data Type:	float64
Description:	Specifies an amount of time to wait after the Start Trigger is received before acquiring or generating the first sample. This value is in the units you specify with DAQmx_StartTrig_DelayUnits.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_DelayUnits

Data Type:	int32
Description:	Specifies the units of DAQmx_StartTrig_Delay.

Valid values

DAQmx_Val_SampClkPeriods	10286	Complete periods of the Sample Clock.
DAQmx_Val_Seconds	10364	Seconds.
DAQmx_Val_Ticks	10304	Timebase ticks.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_Retriggerable

Data Type:	bool32
Description:	Specifies whether a finite task resets and waits for another Start Trigger after the task completes. When you set this property to TRUE, the device performs a finite acquisition or generation each time the Start Trigger occurs until the task stops. The device ignores a trigger if it is in the process of acquiring or generating signals.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_TrigWin

Data Type:	float64
Description:	Specifies the period of time in seconds after the task starts during which the device may trigger. Once the window has expired, the device stops detecting triggers, and the task will finish after the device finishes acquiring post-trigger samples for any triggers detected. If no triggers are detected during the entire period, then no data will be returned. Ensure the period of time specified covers the entire time span desired for trigger detection to avoid missed triggers. Specifying a Trigger Window of -1 causes the window to be infinite.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_RetriggerWin

Data Type:	float64
Description:	Specifies the period of time in seconds after each trigger during which the device may trigger. Once the window has expired, the device stops detecting triggers, and the task will finish after the device finishes acquiring post-trigger samples that it already started. Ensure the period of time specified covers the entire time span desired for retrigger detection to avoid missed triggers. Specifying a Retrigger Window of -1 causes the window to be infinite.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_StartTrig_MaxNumTrigsToDetect

Data Type:	uInt32
Description:	Specifies the maximum number of times the task will detect a start trigger during the task. The number of times a trigger is detected and acted upon by the module may be less than the specified amount if the task stops early because of trigger/retrigger window expiration. Specifying the Maximum Number of Triggers to Detect to be 0 causes the driver to automatically set this value to the maximum possible number of triggers detectable by the device and configuration combination. Note: The number of detected triggers may be less than number of trigger events occurring, because the devices were unable to respond to the trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference

DAQmx_RefTrig_Type

Data Type:	int32
Description:	Specifies the type of trigger to use to mark a reference point for the measurement.

Valid values

DAQmx_Val_AnlgEdge	10099	Trigger when an analog signal signal crosses a threshold.
DAQmx_Val_AnlgMultiEdge	16108	Trigger when any of the configured analog signals cross their respective thresholds.
DAQmx_Val_DigEdge	10150	Trigger on the rising or falling edge of a digital signal.
DAQmx_Val_DigPattern	10398	Trigger when digital physical channels match a digital pattern.
DAQmx_Val_AnlgWin	10103	Trigger when an analog signal enters or leaves a range of values. The range is in the units of the measurement.
DAQmx_Val_Time	15996	Trigger when a specified time is reached.
DAQmx_Val_None	10230	Disable triggering for the task.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_PretrigSamples

Data Type:	uInt32
Description:	Specifies the minimum number of pretrigger samples to acquire from each channel before recognizing the reference trigger. Post-trigger samples per channel are equal to DAQmx_SampQuant_SampPerChan minus the number of pretrigger samples per channel.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_Term

Data Type:	char*
Description:	Indicates the name of the internal Reference Trigger terminal for the task. This property does not return the name of the trigger source terminal.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Reference Digital Edge

DAQmx_DigEdge_RefTrig_Src

Data Type:	char*
Description:	Specifies the name of a terminal where there is a digital signal to use as the source of the Reference Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_RefTrig_Edge

Data Type:	int32
Description:	Specifies on what edge of a digital pulse the Reference Trigger occurs.

Valid values

DAQmx_Val_Rising	10280	Rising edge(s).
DAQmx_Val_Falling	10171	Falling edge(s).

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Digital Edge Digital Filter

DAQmx_DigEdge_RefTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the trigger signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_RefTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Digital Edge Timebase

DAQmx_DigEdge_RefTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_RefTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Digital Edge Digital Synchronization

DAQmx_DigEdge_RefTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Digital Pattern

DAQmx_DigPattern_RefTrig_Src

Data Type:	char*
Description:	Specifies the physical channels to use for pattern matching. The order of the physical channels determines the order of the pattern. If a port is included, the order of the physical channels within the port is in ascending order.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_RefTrig_Pattern

Data Type:	char*
Description:	Specifies the digital pattern that must be met for the Reference Trigger to occur.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_RefTrig_When

Data Type:	int32
Description:	Specifies whether the Reference Trigger occurs when the physical channels specified with DAQmx_DigPattern_RefTrig_Src match or differ from the digital pattern specified with DAQmx_DigPattern_RefTrig_Pattern.

Valid values

DAQmx_Val_PatternMatches	10254	Trigger when the physical channels match the specified pattern.
DAQmx_Val_PatternDoesNotMatch	10253	Trigger when the physical channels do not match the specified pattern.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Edge

DAQmx_AnlgEdge_RefTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the Reference Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_Slope

Data Type:	int32
Description:	Specifies on which slope of the source signal the Reference Trigger occurs.

Valid values

DAQmx_Val_RisingSlope	10280	Trigger on the rising slope of the signal.
DAQmx_Val_FallingSlope	10171	Trigger on the falling slope of the signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_Lvl

Data Type:	float64
Description:	Specifies in the units of the measurement the threshold at which the Reference Trigger occurs. Use DAQmx_AnlgEdge_RefTrig_Slope to specify on which slope to trigger at this threshold.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_Hyst

Data Type:	float64
Description:	Specifies a hysteresis level in the units of the measurement. If DAQmx_AnlgEdge_RefTrig_Slope is DAQmx_Val_RisingSlope, the trigger does not deassert until the source signal passes below DAQmx_AnlgEdge_RefTrig_Lvl minus the hysteresis. If DAQmx_AnlgEdge_RefTrig_Slope is DAQmx_Val_FallingSlope, the trigger does not deassert until the source signal passes above DAQmx_AnlgEdge_RefTrig_Lvl plus the hysteresis. Hysteresis is always enabled. Set this property to a non-zero value to use hysteresis.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Edge Digital Filter

DAQmx_AnlgEdge_RefTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay above or below the trigger level for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the hysteresis window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width thefilter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Edge Timebase

DAQmx_AnlgEdge_RefTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgEdge_RefTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Edge Digital Synchronization

DAQmx_AnlgEdge_RefTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Multiple Edge

DAQmx_AnlgMultiEdge_RefTrig_Srcs

Data Type:	char*
Description:	Specifies a List and/or range of analog sources that are going to be used for Analog triggering. Each source corresponds to an element in each of the Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_RefTrig_Slopes

Data Type:	int32*
Description:	Specifies an array of slopes on which to trigger task to start generating or acquiring samples. Each element of the array corresponds to a source in Ref.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

Valid values

DAQmx_Val_RisingSlope	10280	Trigger on the rising slope of the signal.
DAQmx_Val_FallingSlope	10171	Trigger on the falling slope of the signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_RefTrig_Lvls

Data Type:	float64*
Description:	Specifies an array of thresholds in the units of the measurement or generation to start acquiring or generating samples. Each element of the array corresponds to a source in Ref.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_RefTrig_Hysts

Data Type:	float64*
Description:	Specifies an array of hysteresis levels in the units of the measurement or generation. If the corresponding element of Ref.AnlgMultiEdge.Slopes is Rising, the trigger does not deassert until the source signal passes below the corresponding element of Ref.AnlgMultiEdge.Lvls minus the hysteresis. If Ref.AnlgEdge.Slope is Falling, the trigger does not deassert until the source signal passes above Ref.AnlgEdge.Lvl plus the hysteresis. Hysteresis is always enabled. Set this property to a non-zero value to use hysteresis. Each element of the array corresponds to a source in Ref.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgMultiEdge_RefTrig_Couplings

Data Type:	int32*
Description:	Specifies an array that describes the couplings for the corresponding source signal of the trigger if the source is a terminal rather than a virtual channel. Each element of the array corresponds to a source in Ref.AnlgMultiEdge.Srcs and an element in each of the other Analog Multi Edge property arrays, if they are not empty.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Window

DAQmx_AnlgWin_RefTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the Reference Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_When

Data Type:	int32
Description:	Specifies whether the Reference Trigger occurs when the source signal enters the window or when it leaves the window. Use DAQmx_AnlgWin_RefTrig_Btm and DAQmx_AnlgWin_RefTrig_Top to specify the window.

Valid values

DAQmx_Val_EnteringWin	10163	Trigger when the signal enters the window.
DAQmx_Val_LeavingWin	10208	Trigger when the signal leaves the window.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_Top

Data Type:	float64
Description:	Specifies the upper limit of the window. Specify this value in the units of the measurement.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_Btm

Data Type:	float64
Description:	Specifies the lower limit of the window. Specify this value in the units of the measurement.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Window Digital Filter

DAQmx_AnlgWin_RefTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay within the trigger window for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Window Timebase

DAQmx_AnlgWin_RefTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_RefTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Reference Analog Window Digital Synchronization

DAQmx_AnlgWin_RefTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Auto Trigger

DAQmx_RefTrig_AutoTrigEnable

Data Type:	bool32
Description:	Specifies whether to send a software trigger to the device when a hardware trigger is no longer active in order to prevent a timeout.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_AutoTriggered

Data Type:	bool32
Description:	Indicates whether a completed acquisition was triggered by the auto trigger. If an acquisition has not completed after the task starts, this property returns FALSE. This property is only applicable when DAQmx_RefTrig_AutoTrigEnable is TRUE.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Reference Timestamp

DAQmx_RefTrig_TimestampEnable

Data Type:	bool32
Description:	Specifies whether the reference trigger timestamp is enabled. If the timestamp is enabled but no resources are available, an error will be returned at run time.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_TimestampTimescale

Data Type:	int32
Description:	Specifies the reference trigger timestamp timescale.

Valid values

DAQmx_Val_HostTime	16126	Use the host device.
DAQmx_Val_IODeviceTime	16127	Use the I/O device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_TimestampVal

Data Type:	CVIAbsoluteTime
Description:	Indicates the reference trigger timestamp value.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Reference More

DAQmx_RefTrig_Delay

Data Type:	float64
Description:	Specifies in seconds the time to wait after the device receives the Reference Trigger before switching from pretrigger to posttrigger samples.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_Retriggerable

Data Type:	bool32
Description:	Specifies whether a finite task resets, acquires pretrigger samples, and waits for another Reference Trigger after the task completes. When you set this property to TRUE, the device will acquire post-trigger samples, reset, and acquire pretrigger samples each time the Reference Trigger occurs until the task stops. The device ignores a trigger if it is in the process of acquiring signals.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_TrigWin

Data Type:	float64
Description:	Specifies the duration in seconds after the task starts during which the device may trigger. Once the window has passed, the device stops detecting triggers, and the task will stop after the device finishes acquiring post-trigger samples that it already started. If no triggers are detected during the entire period, then no data will be returned. Specifying a Trigger Window of -1 causes the window to be infinite.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_RetriggerWin

Data Type:	float64
Description:	Specifies the duration in seconds after each trigger during which the device may trigger. Once the window has passed, the device stops detecting triggers, and the task will stop after the device finishes acquiring post-trigger samples that it already started. Specifying a Retrigger Window of -1 causes the window to be infinite.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_RefTrig_MaxNumTrigsToDetect

Data Type:	uInt32
Description:	Specifies the maximum number of times the task will detect a reference trigger during the task. The number of times a trigger is detected and acted upon by the module may be less than the specified amount if the task stops early because of trigger/retrigger window expiration. Specifying the Maximum Number of Triggers to Detect to be 0 causes the driver to automatically set this value to the maximum possible number of triggers detectable by the device and configuration combination. Note: The number of detected triggers may be less than number of trigger events occurring, because the devices were unable to respond to the trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

More

Handshake

DAQmx_HshkTrig_Type

Data Type:	int32
Description:	Specifies the type of Handshake Trigger to use.

Valid values

DAQmx_Val_Interlocked	12549	Use the Handshake Trigger as a control signal for asynchronous handshaking, such as 8255 handshaking.
DAQmx_Val_None	10230	Start the measurement or generation immediately when you start the task.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Interlocked

DAQmx_Interlocked_HshkTrig_Src

Data Type:	char*
Description:	Specifies the source terminal of the Handshake Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_Interlocked_HshkTrig_AssertedLvl

Data Type:	int32
Description:	Specifies the asserted level of the Handshake Trigger.

Valid values

DAQmx_Val_High	10192	High state.
DAQmx_Val_Low	10214	Low state.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause

DAQmx_PauseTrig_Type

Data Type:	int32
Description:	Specifies the type of trigger to use to pause a task.

Valid values

DAQmx_Val_AnlgLvl	10101	Pause the measurement or generation while an analog signal is above or below a level.
DAQmx_Val_AnlgWin	10103	Pause the measurement or generation while an analog signal is either inside or outside of a range of values.
DAQmx_Val_DigLvl	10152	Pause the measurement or generation while a digital signal is at either a high or low state.
DAQmx_Val_DigPattern	10398	Pause the measurement or generation while digital physical channels either match or do not match a digital pattern.
DAQmx_Val_None	10230	Do not pause the measurement or generation.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_PauseTrig_Term

Data Type:	char*
Description:	Indicates the name of the internal Pause Trigger terminal for the task. This property does not return the name of the trigger source terminal.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Analog Level

DAQmx_AnlgLvl_PauseTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_When

Data Type:	int32
Description:	Specifies whether the task pauses above or below the threshold you specify with DAQmx_AnlgLvl_PauseTrig_Lvl.

Valid values

DAQmx_Val_AboveLvl	10093	Pause the measurement or generation while the signal is above the threshold.
DAQmx_Val_BelowLvl	10107	Pause the measurement or generation while the signal is below the threshold.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_Lvl

Data Type:	float64
Description:	Specifies the threshold at which to pause the task. Specify this value in the units of the measurement or generation. Use DAQmx_AnlgLvl_PauseTrig_When to specify whether the task pauses above or below this threshold.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_Hyst

Data Type:	float64
Description:	Specifies a hysteresis level in the units of the measurement or generation. If DAQmx_AnlgLvl_PauseTrig_When is DAQmx_Val_AboveLvl, the trigger does not deassert until the source signal passes below DAQmx_AnlgLvl_PauseTrig_Lvl minus the hysteresis. If DAQmx_AnlgLvl_PauseTrig_When is DAQmx_Val_BelowLvl, the trigger does not deassert until the source signal passes above DAQmx_AnlgLvl_PauseTrig_Lvl plus the hysteresis. Hysteresis is always enabled. Set this property to a non-zero value to use hysteresis.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the trigger if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Level Digital Filter

DAQmx_AnlgLvl_PauseTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay above or below the trigger level for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the hysteresis window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Level Timebase

DAQmx_AnlgLvl_PauseTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgLvl_PauseTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Level Digital Synchronization

DAQmx_AnlgLvl_PauseTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Analog Window

DAQmx_AnlgWin_PauseTrig_Src

Data Type:	char*
Description:	Specifies the name of a virtual channel or terminal where there is an analog signal to use as the source of the trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_When

Data Type:	int32
Description:	Specifies whether the task pauses while the trigger signal is inside or outside the window you specify with DAQmx_AnlgWin_PauseTrig_Btm and DAQmx_AnlgWin_PauseTrig_Top.

Valid values

DAQmx_Val_InsideWin	10199	Pause the measurement or generation while the trigger is inside the window.
DAQmx_Val_OutsideWin	10251	Pause the measurement or generation while the signal is outside the window.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_Top

Data Type:	float64
Description:	Specifies the upper limit of the window. Specify this value in the units of the measurement or generation.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_Btm

Data Type:	float64
Description:	Specifies the lower limit of the window. Specify this value in the units of the measurement or generation.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_Coupling

Data Type:	int32
Description:	Specifies the coupling for the source signal of the terminal if the source is a terminal rather than a virtual channel.

Valid values

DAQmx_Val_AC	10045	Alternating Current.
DAQmx_Val_DC	10050	Direct Current.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Window Digital Filter

DAQmx_AnlgWin_PauseTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the digital output of the analog triggering circuitry (the Analog Comparison Event). When enabled, the analog signal must stay within the trigger window for the minimum pulse width before being recognized. Use filtering for noisy trigger signals that transition in and out of the window rapidly.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Window Timebase

DAQmx_AnlgWin_PauseTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the terminal of the signal to use as the timebase of the digital filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_AnlgWin_PauseTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the digital filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Analog Window Digital Synchronization

DAQmx_AnlgWin_PauseTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Digital Level

DAQmx_DigLvl_PauseTrig_Src

Data Type:	char*
Description:	Specifies the name of a terminal where there is a digital signal to use as the source of the Pause Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigLvl_PauseTrig_When

Data Type:	int32
Description:	Specifies whether the task pauses while the signal is high or low.

Valid values

DAQmx_Val_High	10192	High state.
DAQmx_Val_Low	10214	Low state.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Digital Level Digital Filter

DAQmx_DigLvl_PauseTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply a digital filter to the trigger signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigLvl_PauseTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Digital Level Timebase

DAQmx_DigLvl_PauseTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the input terminal of the signal to use as the timebase of the pulse width filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigLvl_PauseTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the pulse width filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Digital Level Digital Synchronization

DAQmx_DigLvl_PauseTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Pause Digital Pattern

DAQmx_DigPattern_PauseTrig_Src

Data Type:	char*
Description:	Specifies the physical channels to use for pattern matching. The order of the physical channels determines the order of the pattern. If a port is included, the lines within the port are in ascending order.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_PauseTrig_Pattern

Data Type:	char*
Description:	Specifies the digital pattern that must be met for the Pause Trigger to occur.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigPattern_PauseTrig_When

Data Type:	int32
Description:	Specifies if the Pause Trigger occurs when the physical channels specified with DAQmx_DigPattern_PauseTrig_Src match or differ from the digital pattern specified with DAQmx_DigPattern_PauseTrig_Pattern.

Valid values

DAQmx_Val_PatternMatches	10254	Trigger when the physical channels match the specified pattern.
DAQmx_Val_PatternDoesNotMatch	10253	Trigger when the physical channels do not match the specified pattern.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start

DAQmx_ArmStartTrig_Type

Data Type:	int32
Description:	Specifies the type of trigger to use to arm the task for a Start Trigger. If you configure an Arm Start Trigger, the task does not respond to a Start Trigger until the device receives the Arm Start Trigger.

Valid values

DAQmx_Val_DigEdge	10150	Trigger on a rising or falling edge of a digital signal.
DAQmx_Val_Time	15996	Trigger when a specified time is reached.
DAQmx_Val_None	10230	Disable the trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_ArmStart_Term

Data Type:	char*
Description:	Indicates the name of the internal Arm Start Trigger terminal for the task. This property does not return the name of the trigger source terminal.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Arm Start Digital Edge

DAQmx_DigEdge_ArmStartTrig_Src

Data Type:	char*
Description:	Specifies the name of a terminal where there is a digital signal to use as the source of the Arm Start Trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_ArmStartTrig_Edge

Data Type:	int32
Description:	Specifies on which edge of a digital signal to arm the task for a Start Trigger.

Valid values

DAQmx_Val_Rising	10280	Rising edge(s).
DAQmx_Val_Falling	10171	Falling edge(s).

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start Digital Edge Digital Filter

DAQmx_DigEdge_ArmStartTrig_DigFltr_Enable

Data Type:	bool32
Description:	Specifies whether to apply the pulse width filter to the signal.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_ArmStartTrig_DigFltr_MinPulseWidth

Data Type:	float64
Description:	Specifies in seconds the minimum pulse width the filter recognizes.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start Digital Edge Timebase

DAQmx_DigEdge_ArmStartTrig_DigFltr_TimebaseSrc

Data Type:	char*
Description:	Specifies the input terminal of the signal to use as the timebase of the pulse width filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_DigEdge_ArmStartTrig_DigFltr_TimebaseRate

Data Type:	float64
Description:	Specifies in hertz the rate of the pulse width filter timebase. NI-DAQmx uses this value to compute settings for the filter.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start Digital Edge Digital Synchronization

DAQmx_DigEdge_ArmStartTrig_DigSync_Enable

Data Type:	bool32
Description:	Specifies whether to synchronize recognition of transitions in the signal to the internal timebase of the device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start Time

DAQmx_ArmStartTrig_TrigWhen

Data Type:	CVIAbsoluteTime
Description:	Specifies when to trigger the arm start trigger.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_ArmStartTrig_Timescale

Data Type:	int32
Description:	Specifies the timescale to be used for timestamps used in an arm start time trigger.

Valid values

DAQmx_Val_HostTime	16126	Use the host device.
DAQmx_Val_IODeviceTime	16127	Use the I/O device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

Arm Start Timestamp

DAQmx_ArmStartTrig_TimestampEnable

Data Type:	bool32
Description:	Specifies whether the arm start trigger timestamp is enabled. If the timestamp is enabled but no resources are available, an error will be returned at run time.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_ArmStartTrig_TimestampTimescale

Data Type:	int32
Description:	Specifies the arm start trigger timestamp timescale.

Valid values

DAQmx_Val_HostTime	16126	Use the host device.
DAQmx_Val_IODeviceTime	16127	Use the I/O device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

DAQmx_ArmStartTrig_TimestampVal

Data Type:	CVIAbsoluteTime
Description:	Indicates the arm start trigger timestamp value.
Restrictions:	Not Settable

You can get this attribute using: DAQmxGetTrigAttribute

Advanced

DAQmx_Trigger_SyncType

Data Type:	int32
Description:	Specifies the role of the device in a synchronized system. Setting this value to DAQmx_Val_Master or DAQmx_Val_Slave enables trigger skew correction. If you enable trigger skew correction, set this property to DAQmx_Val_Master on only one device, and set this property to DAQmx_Val_Slave on the other devices.

Valid values

DAQmx_Val_None	10230	Disables trigger skew correction.
DAQmx_Val_Master	15888	Device is the source for shared clocks and triggers.
DAQmx_Val_Slave	15889	Device uses clocks and triggers from the master device.

You can get/set/reset this attribute using: DAQmxGetTrigAttribute DAQmxSetTrigAttribute DAQmxResetTrigAttribute

NI-DAQmx

gRPC API Differences From C API

Task Configuration And Control

Channel Configuration And Creation

Timing

Triggering

Read Functions

Write Functions

Export Hardware Signals

Scale Configuration

Internal Buffer Configuration

Advanced Functions

System Configuration

Error Handling

Buffer Attributes

Calibration Info Attributes

Channel Attributes

Device Attributes

Export Signal Attributes

Persisted Channel Attributes

Persisted Scale Attributes

Persisted Task Attributes

Physical Channel Attributes

Read Attributes

Scale Attributes

System Attributes

Task Attributes

Timing Attributes

Trigger Attributes

Watchdog Attributes

Write Attributes

NI-DCPOWER

Setup Functions

Configure Functions

Measurement Functions

Control Functions

Trigger And Event
Attribute Functions

Query Functions

Calibration Functions

Utility Functions

Supported Device
Source Attributes

Transient Attributes

Voltage Attributes

Current Attributes

Pulse Voltage Attributes

Pulse Current Attributes

Cutoff Attributes

Measurement Attributes

Trigger Attributes Functions

Event Attributes

Advanced Attributes

Inherent Ivi Attributes

Supported Device Attributes

NI-DIGITAL PATTERN DRIVER

Init And Close Functions

Session Locking Functions

Utility Functions

Error Handling Functions

Calibration Functions

Attributes Functions

Pin Map Functions

Low Level Functions

Low Level Action Functions

Pin Control Functions

Static IO Functions

Clock Generator Functions

Levels And Timing Functions

TDR Functions

PPMU Configuration Functions

DC Voltage Functions

DC Current Functions

PPMU Action Functions

Pattern Configuration Functions

Pattern Action Functions

History Ram Functions

Source Memory Functions

Capture Memory Functions

Triggers And Events Functions

Conditional Jump Trigger Functions

Sequencer Flag Functions

Sequencer Register Functions

Match Fail Combination Functions

Pattern Results Functions

Sort Results Functions

Frequency Measurement Functions

IVI Inherent Attributes

Specific Driver Information Attributes, Read Only

Driver Setup Information Attributes

Device Attributes

Pin Control Attributes

Level Configuration Attributes

Trigger Configuration Attributes

PPMU Attributes

Patterns Attributes

Pattern Opcode Event Attributes

Timing Offset Attributes

Keep Alive Attributes

Frequency Measurement Attributes

Clock Generator Attributes

History RAM

Synchronization Attributes

TDR Endpoint Termination Attributes

NI-DMM

Setup Functions

Configuration Functions

Measurement Functions

Trigger Functions

Values And Attribute Functions

Acquisition Functions

Calibration Functions

Utility Functions

Configuration Attributes

Inherent IVI Attributes

Multi Point Acquisition Attributes

NI-FGEN

Setup Functions

Configuration Functions

Standard Output Functions

Arbitrary Waveform Output Functions

Arbitrary Sequence Output Functions

Incremental Waveform Write Functions

Configure Clock Functions

Trigger And Syncronizations Functions

5404 Routing Functions

Script Output Functions

Configure Onboard Signal Processing Functions

Configure Peer To Peer Functions

Attribute Functions

Waveform Control Functions

Error Functions

Output Attributes

Arbitrary Waveform Attributes

Data Transfer Attributes

Onboard Signal Processing Attributes

Peer To Peer Attributes

Standard Function Attributes

Clock Attributes

Event Attributes

Triggering Attributes

Instrument Specific Attributes

Inherent IVI Attributes

5401 5411 5431

NI-FPGA

gRPC API Differences From C API

NI FPGA C Functions

NI-RFmx Bluetooth

gRPC API Differences From C API

General Functions

Configuration Functions

Set And Get Attribute Functions

Fetch Results Functions

Utility Functions

Build String Functions

Advanced Functions

General Attributes

Trigger Attributes

Packet Attributes

Auto Detect Signal Attributes

Modacc Attributes

ACP Attributes

Twenty dB Attributes

Frequency Range Attributes

TXP Attributes

Advanced Attributes

NI-RFmx NR

gRPC API Differences From C API

General Functions

Configuration Functions

Set And Get Attributes Functions

Fetch Results Functions

Utility Functions

Build String Functions

Advanced Functions

General Attributes

Trigger Attributes

Signal Detection Attributes

Component Carrier Attributes

List Attributes

Modacc Attributes

ACP Attributes

CHP Attributes

OBW Attributes

SEM Attributes

TXP Attributes

Pvt Attributes

Advanced Attributes

NI-RFmx WCDMA

gRPC API Differences From C API

NI RFmx WCDMA C Functions

NI-RFmx GSM

gRPC API Differences From C API

NI RFmx GSM C Functions

NI-RFmx CDMA2k

gRPC API Differences From C API

NI RFmx CDMA2k C Functions

NI-RFmx Instr

General Functions

Configuration Functions

Set And Get Attributes Functions

Utility

Build String

Calibration

Attributes

Advanced Attributes

NI-RFmx LTE

gRPC API Differences From C API

General Functions

Configuration Functions

Ch Configuration Functions

NB IoT Configuration Functions

ModAcc Configuration Functions

ACP Configuration Functions

CHP Configuration Functions

OBW Configuration Functions

SEM Configuration Functions

PVT Configuration Functions

SlotPhase Configuration Functions

SlotPower Configuration Functions

Set And Get Attribute Functions

ModAcc Fetch Functions

ACP Fetch Functions

CHP Fetch Functions

OBW Fetch Functions

SEM Fetch Functions

PVT Fetch Functions

SlotPhase Fetch Functions

SlotPower Fetch Functions

Utility Functions

Build String Functions

Advanced Functions

General Attributes

Trigger Attributes

Component Carrier Attributes

ModAcc Attributes

ACP Attributes

CHP Attributes

OBW Attributes

SEM Attributes

PVT Attributes

SlotPhase Attributes

SlotPower Attributes

Advanced Attributes

NI-RFmx SpecAn

gRPC API Differences From C API

General Functions

Configuration Functions

Set And Get Attribute Functions

Read Functions

Fetch Functions

Utility Functions

Marker Functions

Build String Functions

Advanced Functions

General Attributes

Trigger Attributes

ACP Attributes

Cdf Attributes

CHP Attributes

Fcnt Attributes

Harm Attributes

OBW Attributes

SEM Attributes

Spectrum Attributes

Spur Attributes

TXP Attributes

AMPM Attributes

Dpd Attributes

IQ Attributes

IM Attributes

NF Attributes

Phasenoise Attributes

PAVT Attributes

Advanced Attributes

NI-RFmx TD-SCDMA

gRPC API Differences From C API

NI RFmx TD-SCDMA C Functions

NI-RFmx WLAN

gRPC API Differences From C API

General Functions

Configuration Functions

Set And Get Attribute Functions

Fetch DSSS ModAcc Functions

Fetch OFDM ModAcc Functions

Fetch SEM Functions

Fetch TXP Functions

Fetch PowerRamp Functions

Utility Functions

Build String Functions

Advanced Functions

General Attributes

Trigger Attributes

OFDM Attributes

Auto Detect Signal Attributes

DSSS ModAcc Attributes

OFDM ModAcc Attributes

SEM Attributes

TXP Attributes

PowerRamp Attributes

Advanced Attributes

NI-RFSA

General Functions

Configuration Functions

Acquisition Functions

Utility Functions

Calibration Functions

General Attributes

Vertical Attributes

Signal Path Attributes

Acquisition Attributes

Acquisition Attributes

Triggers Attributes

Events Attributes

Device Characteristics Attributes

Peer To Peer Streaming Attributes

Configuration List Attributes

Inherent IVI Properties Attributes

De-embedding Attributes

Self Calibration Attributes

Factory Calibration Attributes

External Alignment Attributes

Device Specific Attributes

NI-RFSG

General Functions

Generation Configuration

Utility Functions

Calibration Functions

Arb Attributes

Clock Attributes

Configuration List Attributes

De-embedding Attributes

Device Characteristics Attributes

Device Specific Attributes

Events Attributes

External Calibration Attributes

Inherent IVI Attributes Attributes

IQ Impairment Attributes

Load Configurations Attributes

Modulation Attributes

Obsolete Attributes

Peer To Peer Attributes

RF Attributes

Self Calibration Attributes

Triggers Attributes

NI-SCOPE

Setup Functions

Configure Functions

Attribute Functions

Acquisition Functions

Measurement Functions

Calibrate Functions

Utility Funcitons

Error Handling Functions

IVI Compliance Or Obsolete Functions

Vertical Attributes

Horizontal Attributes

Trigger Attributes

Clocking Attributes

Synchronization Attributes

Acquisition Attributes

Waveform Measurements Attributes

Onboard Signal Processing Attributes

Peer To Peer Streaming Attributes

Device Attributes

IVI Or Obsolete Attributes

Instrument Capabilities Attributes

If Digitizer Attributes

NI-SWITCH

Setup Functions

Attribute Functions

Route Functions

Scan Functions

Relay Functions

Utility Functions

Value Constants

Channel Configuration Attributes

IVI Attributes

Matrix Configuration Attributes

Module Characteristics Attributes

Scanning Configuration Attributes

NI-TCLK

High-level Functions

Advanced Functions

Attribute Functions

NI-XNET

gRPC API differences from C APIs

General Functions

Cluster Properties

Database Properties

Device Properties

ECU Properties

Frame Properties

Interface Properties

LIN Schedule Entry Properties

LIN Schedule Properties

PDU Properties

Session Ethernet Properties

Session Frame Properties

Session Interface Properties

Session Properties

Session SAE J1939 Properties

Signal Properties

Subframe Properties

System Properties

IP-Stack Functions

Socket Options

Socket Functions