I2C with the Linux bitbanging interface activated #19

FrankBuss · 2012-05-11T00:06:54Z

See http://www.raspberrypi.org/forum/projects-and-collaboration-general/linux-device-drivers-for-rapberry-pi-on-board-io/page-4 for details. I'll try to implement a driver which uses the I2C hardware module of the microcontroller this weekend, but might need some more time and until then, this is a stable intermediate solution.
Edit: the real driver is now available: http://www.bootc.net/archives/2012/05/19/i2c-and-the-raspberry-pi/ no need for GPIO at the moment, but maybe could be enabled by kernel config instead of the hardware driver, if there are problems

… rpi-patches

…uld be loaded before all other modules

bcm2708: Fix i2c platform device registration when CONFIG_I2C_GPIO=m

… rpi-patches

popcornmix · 2012-05-26T15:37:34Z

Thanks for this, but I'll close this, as the drivers in bootc's kernel are likely to be used in the upstream kernel.
I believe your code was incorporated into his driver.

FrankBuss · 2012-05-26T16:09:47Z

right, bootc has integrated my new interrupt based code for the BSC hardware in his driver, and so far no problems reported from people who tested it, so maybe no need for a GPIO fallback

asb · 2012-05-26T16:10:57Z

Plus I think the plan is when we move to a devicetree-enabled kernel it will be possible to enable that fallback through the appropriate devicetree stanza.

…d reasons commit 5cf02d0 upstream. We've had some reports of a deadlock where rpciod ends up with a stack trace like this: PID: 2507 TASK: ffff88103691ab40 CPU: 14 COMMAND: "rpciod/14" #0 [ffff8810343bf2f0] schedule at ffffffff814dabd9 raspberrypi#1 [ffff8810343bf3b8] nfs_wait_bit_killable at ffffffffa038fc04 [nfs] raspberrypi#2 [ffff8810343bf3c8] __wait_on_bit at ffffffff814dbc2f raspberrypi#3 [ffff8810343bf418] out_of_line_wait_on_bit at ffffffff814dbcd8 raspberrypi#4 [ffff8810343bf488] nfs_commit_inode at ffffffffa039e0c1 [nfs] raspberrypi#5 [ffff8810343bf4f8] nfs_release_page at ffffffffa038bef6 [nfs] raspberrypi#6 [ffff8810343bf528] try_to_release_page at ffffffff8110c670 raspberrypi#7 [ffff8810343bf538] shrink_page_list.clone.0 at ffffffff81126271 raspberrypi#8 [ffff8810343bf668] shrink_inactive_list at ffffffff81126638 raspberrypi#9 [ffff8810343bf818] shrink_zone at ffffffff8112788f raspberrypi#10 [ffff8810343bf8c8] do_try_to_free_pages at ffffffff81127b1e raspberrypi#11 [ffff8810343bf958] try_to_free_pages at ffffffff8112812f raspberrypi#12 [ffff8810343bfa08] __alloc_pages_nodemask at ffffffff8111fdad raspberrypi#13 [ffff8810343bfb28] kmem_getpages at ffffffff81159942 raspberrypi#14 [ffff8810343bfb58] fallback_alloc at ffffffff8115a55a raspberrypi#15 [ffff8810343bfbd8] ____cache_alloc_node at ffffffff8115a2d9 raspberrypi#16 [ffff8810343bfc38] kmem_cache_alloc at ffffffff8115b09b raspberrypi#17 [ffff8810343bfc78] sk_prot_alloc at ffffffff81411808 raspberrypi#18 [ffff8810343bfcb8] sk_alloc at ffffffff8141197c raspberrypi#19 [ffff8810343bfce8] inet_create at ffffffff81483ba6 raspberrypi#20 [ffff8810343bfd38] __sock_create at ffffffff8140b4a7 raspberrypi#21 [ffff8810343bfd98] xs_create_sock at ffffffffa01f649b [sunrpc] raspberrypi#22 [ffff8810343bfdd8] xs_tcp_setup_socket at ffffffffa01f6965 [sunrpc] raspberrypi#23 [ffff8810343bfe38] worker_thread at ffffffff810887d0 raspberrypi#24 [ffff8810343bfee8] kthread at ffffffff8108dd96 raspberrypi#25 [ffff8810343bff48] kernel_thread at ffffffff8100c1ca rpciod is trying to allocate memory for a new socket to talk to the server. The VM ends up calling ->releasepage to get more memory, and it tries to do a blocking commit. That commit can't succeed however without a connected socket, so we deadlock. Fix this by setting PF_FSTRANS on the workqueue task prior to doing the socket allocation, and having nfs_release_page check for that flag when deciding whether to do a commit call. Also, set PF_FSTRANS unconditionally in rpc_async_schedule since that function can also do allocations sometimes. Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

Printing the "start_ip" for every secondary cpu is very noisy on a large system - and doesn't add any value. Drop this message. Console log before: Booting Node 0, Processors #1 smpboot cpu 1: start_ip = 96000 #2 smpboot cpu 2: start_ip = 96000 #3 smpboot cpu 3: start_ip = 96000 #4 smpboot cpu 4: start_ip = 96000 ... #31 smpboot cpu 31: start_ip = 96000 Brought up 32 CPUs Console log after: Booting Node 0, Processors #1 #2 #3 #4 #5 #6 #7 Ok. Booting Node 1, Processors #8 #9 #10 #11 #12 #13 #14 #15 Ok. Booting Node 0, Processors #16 #17 #18 #19 #20 #21 #22 #23 Ok. Booting Node 1, Processors #24 #25 #26 #27 #28 #29 #30 #31 Brought up 32 CPUs Acked-by: Borislav Petkov <bp@amd64.org> Signed-off-by: Tony Luck <tony.luck@intel.com> Link: http://lkml.kernel.org/r/4f452eb42507460426@agluck-desktop.sc.intel.com Signed-off-by: H. Peter Anvin <hpa@zytor.com>

The warning below triggers on AMD MCM packages because physical package IDs on the cores of a _physical_ socket are the same. I.e., this field says which CPUs belong to the same physical package. However, the same two CPUs belong to two different internal, i.e. "logical" nodes in the same physical socket which is reflected in the CPU-to-node map on x86 with NUMA. Which makes this check wrong on the above topologies so circumvent it. [ 0.444413] Booting Node 0, Processors #1 #2 #3 #4 #5 Ok. [ 0.461388] ------------[ cut here ]------------ [ 0.465997] WARNING: at arch/x86/kernel/smpboot.c:310 topology_sane.clone.1+0x6e/0x81() [ 0.473960] Hardware name: Dinar [ 0.477170] sched: CPU #6's mc-sibling CPU #0 is not on the same node! [node: 1 != 0]. Ignoring dependency. [ 0.486860] Booting Node 1, Processors #6 [ 0.491104] Modules linked in: [ 0.494141] Pid: 0, comm: swapper/6 Not tainted 3.4.0+ #1 [ 0.499510] Call Trace: [ 0.501946] [<ffffffff8144bf92>] ? topology_sane.clone.1+0x6e/0x81 [ 0.508185] [<ffffffff8102f1fc>] warn_slowpath_common+0x85/0x9d [ 0.514163] [<ffffffff8102f2b7>] warn_slowpath_fmt+0x46/0x48 [ 0.519881] [<ffffffff8144bf92>] topology_sane.clone.1+0x6e/0x81 [ 0.525943] [<ffffffff8144c234>] set_cpu_sibling_map+0x251/0x371 [ 0.532004] [<ffffffff8144c4ee>] start_secondary+0x19a/0x218 [ 0.537729] ---[ end trace 4eaa2a86a8e2da22 ]--- [ 0.628197] #7 #8 #9 #10 #11 Ok. [ 0.807108] Booting Node 3, Processors #12 #13 #14 #15 #16 #17 Ok. [ 0.897587] Booting Node 2, Processors #18 #19 #20 #21 #22 #23 Ok. [ 0.917443] Brought up 24 CPUs We ran a topology sanity check test we have here on it and it all looks ok... hopefully :). Signed-off-by: Borislav Petkov <borislav.petkov@amd.com> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20120529135442.GE29157@aftab.osrc.amd.com Signed-off-by: Ingo Molnar <mingo@kernel.org>

…d reasons We've had some reports of a deadlock where rpciod ends up with a stack trace like this: PID: 2507 TASK: ffff88103691ab40 CPU: 14 COMMAND: "rpciod/14" #0 [ffff8810343bf2f0] schedule at ffffffff814dabd9 #1 [ffff8810343bf3b8] nfs_wait_bit_killable at ffffffffa038fc04 [nfs] #2 [ffff8810343bf3c8] __wait_on_bit at ffffffff814dbc2f #3 [ffff8810343bf418] out_of_line_wait_on_bit at ffffffff814dbcd8 #4 [ffff8810343bf488] nfs_commit_inode at ffffffffa039e0c1 [nfs] #5 [ffff8810343bf4f8] nfs_release_page at ffffffffa038bef6 [nfs] #6 [ffff8810343bf528] try_to_release_page at ffffffff8110c670 #7 [ffff8810343bf538] shrink_page_list.clone.0 at ffffffff81126271 #8 [ffff8810343bf668] shrink_inactive_list at ffffffff81126638 #9 [ffff8810343bf818] shrink_zone at ffffffff8112788f #10 [ffff8810343bf8c8] do_try_to_free_pages at ffffffff81127b1e #11 [ffff8810343bf958] try_to_free_pages at ffffffff8112812f #12 [ffff8810343bfa08] __alloc_pages_nodemask at ffffffff8111fdad #13 [ffff8810343bfb28] kmem_getpages at ffffffff81159942 #14 [ffff8810343bfb58] fallback_alloc at ffffffff8115a55a #15 [ffff8810343bfbd8] ____cache_alloc_node at ffffffff8115a2d9 #16 [ffff8810343bfc38] kmem_cache_alloc at ffffffff8115b09b #17 [ffff8810343bfc78] sk_prot_alloc at ffffffff81411808 #18 [ffff8810343bfcb8] sk_alloc at ffffffff8141197c #19 [ffff8810343bfce8] inet_create at ffffffff81483ba6 #20 [ffff8810343bfd38] __sock_create at ffffffff8140b4a7 #21 [ffff8810343bfd98] xs_create_sock at ffffffffa01f649b [sunrpc] #22 [ffff8810343bfdd8] xs_tcp_setup_socket at ffffffffa01f6965 [sunrpc] #23 [ffff8810343bfe38] worker_thread at ffffffff810887d0 #24 [ffff8810343bfee8] kthread at ffffffff8108dd96 #25 [ffff8810343bff48] kernel_thread at ffffffff8100c1ca rpciod is trying to allocate memory for a new socket to talk to the server. The VM ends up calling ->releasepage to get more memory, and it tries to do a blocking commit. That commit can't succeed however without a connected socket, so we deadlock. Fix this by setting PF_FSTRANS on the workqueue task prior to doing the socket allocation, and having nfs_release_page check for that flag when deciding whether to do a commit call. Also, set PF_FSTRANS unconditionally in rpc_async_schedule since that function can also do allocations sometimes. Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: stable@vger.kernel.org

Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>

…s struct file commit e4daf1f upstream. The following call chain: ------------------------------------------------------------ nfs4_get_vfs_file - nfsd_open - dentry_open - do_dentry_open - __get_file_write_access - get_write_access - return atomic_inc_unless_negative(&inode->i_writecount) ? 0 : -ETXTBSY; ------------------------------------------------------------ can result in the following state: ------------------------------------------------------------ struct nfs4_file { ... fi_fds = {0xffff880c1fa65c80, 0xffffffffffffffe6, 0x0}, fi_access = {{ counter = 0x1 }, { counter = 0x0 }}, ... ------------------------------------------------------------ 1) First time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NULL, hence nfsd_open() is called where we get status set to an error and fp->fi_fds[O_WRONLY] to -ETXTBSY. Thus we do not reach nfs4_file_get_access() and fi_access[O_WRONLY] is not incremented. 2) Second time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NOT NULL (-ETXTBSY), so nfsd_open() is NOT called, but nfs4_file_get_access() IS called and fi_access[O_WRONLY] is incremented. Thus we leave a landmine in the form of the nfs4_file data structure in an incorrect state. 3) Eventually, when __nfs4_file_put_access() is called it finds fi_access[O_WRONLY] being non-zero, it decrements it and calls nfs4_file_put_fd() which tries to fput -ETXTBSY. ------------------------------------------------------------ ... [exception RIP: fput+0x9] RIP: ffffffff81177fa9 RSP: ffff88062e365c90 RFLAGS: 00010282 RAX: ffff880c2b3d99cc RBX: ffff880c2b3d9978 RCX: 0000000000000002 RDX: dead000000100101 RSI: 0000000000000001 RDI: ffffffffffffffe6 RBP: ffff88062e365c90 R8: ffff88041fe797d8 R9: ffff88062e365d58 R10: 0000000000000008 R11: 0000000000000000 R12: 0000000000000001 R13: 0000000000000007 R14: 0000000000000000 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #9 [ffff88062e365c98] __nfs4_file_put_access at ffffffffa0562334 [nfsd] #10 [ffff88062e365cc8] nfs4_file_put_access at ffffffffa05623ab [nfsd] #11 [ffff88062e365ce8] free_generic_stateid at ffffffffa056634d [nfsd] #12 [ffff88062e365d18] release_open_stateid at ffffffffa0566e4b [nfsd] #13 [ffff88062e365d38] nfsd4_close at ffffffffa0567401 [nfsd] #14 [ffff88062e365d88] nfsd4_proc_compound at ffffffffa0557f28 [nfsd] #15 [ffff88062e365dd8] nfsd_dispatch at ffffffffa054543e [nfsd] #16 [ffff88062e365e18] svc_process_common at ffffffffa04ba5a4 [sunrpc] #17 [ffff88062e365e98] svc_process at ffffffffa04babe0 [sunrpc] #18 [ffff88062e365eb8] nfsd at ffffffffa0545b62 [nfsd] #19 [ffff88062e365ee8] kthread at ffffffff81090886 #20 [ffff88062e365f48] kernel_thread at ffffffff8100c14a ------------------------------------------------------------ Signed-off-by: Harshula Jayasuriya <harshula@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…s struct file The following call chain: ------------------------------------------------------------ nfs4_get_vfs_file - nfsd_open - dentry_open - do_dentry_open - __get_file_write_access - get_write_access - return atomic_inc_unless_negative(&inode->i_writecount) ? 0 : -ETXTBSY; ------------------------------------------------------------ can result in the following state: ------------------------------------------------------------ struct nfs4_file { ... fi_fds = {0xffff880c1fa65c80, 0xffffffffffffffe6, 0x0}, fi_access = {{ counter = 0x1 }, { counter = 0x0 }}, ... ------------------------------------------------------------ 1) First time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NULL, hence nfsd_open() is called where we get status set to an error and fp->fi_fds[O_WRONLY] to -ETXTBSY. Thus we do not reach nfs4_file_get_access() and fi_access[O_WRONLY] is not incremented. 2) Second time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NOT NULL (-ETXTBSY), so nfsd_open() is NOT called, but nfs4_file_get_access() IS called and fi_access[O_WRONLY] is incremented. Thus we leave a landmine in the form of the nfs4_file data structure in an incorrect state. 3) Eventually, when __nfs4_file_put_access() is called it finds fi_access[O_WRONLY] being non-zero, it decrements it and calls nfs4_file_put_fd() which tries to fput -ETXTBSY. ------------------------------------------------------------ ... [exception RIP: fput+0x9] RIP: ffffffff81177fa9 RSP: ffff88062e365c90 RFLAGS: 00010282 RAX: ffff880c2b3d99cc RBX: ffff880c2b3d9978 RCX: 0000000000000002 RDX: dead000000100101 RSI: 0000000000000001 RDI: ffffffffffffffe6 RBP: ffff88062e365c90 R8: ffff88041fe797d8 R9: ffff88062e365d58 R10: 0000000000000008 R11: 0000000000000000 R12: 0000000000000001 R13: 0000000000000007 R14: 0000000000000000 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #9 [ffff88062e365c98] __nfs4_file_put_access at ffffffffa0562334 [nfsd] #10 [ffff88062e365cc8] nfs4_file_put_access at ffffffffa05623ab [nfsd] #11 [ffff88062e365ce8] free_generic_stateid at ffffffffa056634d [nfsd] #12 [ffff88062e365d18] release_open_stateid at ffffffffa0566e4b [nfsd] #13 [ffff88062e365d38] nfsd4_close at ffffffffa0567401 [nfsd] #14 [ffff88062e365d88] nfsd4_proc_compound at ffffffffa0557f28 [nfsd] #15 [ffff88062e365dd8] nfsd_dispatch at ffffffffa054543e [nfsd] #16 [ffff88062e365e18] svc_process_common at ffffffffa04ba5a4 [sunrpc] #17 [ffff88062e365e98] svc_process at ffffffffa04babe0 [sunrpc] #18 [ffff88062e365eb8] nfsd at ffffffffa0545b62 [nfsd] #19 [ffff88062e365ee8] kthread at ffffffff81090886 #20 [ffff88062e365f48] kernel_thread at ffffffff8100c14a ------------------------------------------------------------ Cc: stable@vger.kernel.org Signed-off-by: Harshula Jayasuriya <harshula@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>

The SDVO code tries to compare the encoder's and crtc's idea of the pixel_multiplier. Normally they have to match, but when transitioning to DPMS off, we turn off the pipe before reading out the pipe_config, so the pixel_multiplier in the pipe_config will be 0, whereas the encoder will still have its pixel_multiplier set to whatever value we were using when the display was active. This leads to a warning from intel_modeset_check_state(). WARNING: CPU: 1 PID: 2846 at drivers/gpu/drm/i915/intel_sdvo.c:1378 intel_sdvo_get_config+0x158/0x160() SDVO pixel multiplier mismatch, port: 0, encoder: 1 Modules linked in: snd_hda_codec_idt snd_hda_intel snd_hda_codec snd_hwdep CPU: 1 PID: 2846 Comm: Xorg Not tainted 3.11.0-rc3-00208-gbe1e8d7-dirty #19 Hardware name: Apple Computer, Inc. Macmini1,1/Mac-F4208EC8, BIOS MM11.88Z.0055.B03.0604071521 04/07/06 00000000 00000000 ef0afa54 c1597bbb c1737ea4 ef0afa84 c10392ca c1737e6c ef0afab0 00000b1e c1737ea4 00000562 c12dfbe8 c12dfbe8 ef0afb14 00000000 f697ec00 ef0afa9c c103936e 00000009 ef0afa94 c1737e6c ef0afab0 ef0afadc Call Trace: [<c1597bbb>] dump_stack+0x41/0x56 [<c10392ca>] warn_slowpath_common+0x7a/0xa0 [<c103936e>] warn_slowpath_fmt+0x2e/0x30 [<c12dfbe8>] intel_sdvo_get_config+0x158/0x160 [<c12c3220>] check_crtc_state+0x1e0/0xb10 [<c12cdc7d>] intel_modeset_check_state+0x29d/0x7c0 [<c12dfe5c>] intel_sdvo_dpms+0x5c/0xa0 [<c12985de>] drm_mode_obj_set_property_ioctl+0x40e/0x420 [<c1298625>] drm_mode_connector_property_set_ioctl+0x35/0x40 [<c1289294>] drm_ioctl+0x3e4/0x540 [<c10fc1a2>] do_vfs_ioctl+0x72/0x570 [<c10fc72f>] SyS_ioctl+0x8f/0xa0 [<c159b7fa>] sysenter_do_call+0x12/0x22 ---[ end trace 7ce940aff1366d60 ]--- Fix the problem by skipping the encoder get_config() function for inactive encoders. Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

When booting secondary CPUs, announce_cpu() is called to show which cpu has been brought up. For example: [ 0.402751] smpboot: Booting Node 0, Processors #1 #2 #3 #4 #5 OK [ 0.525667] smpboot: Booting Node 1, Processors #6 #7 #8 #9 #10 #11 OK [ 0.755592] smpboot: Booting Node 0, Processors #12 #13 #14 #15 #16 #17 OK [ 0.890495] smpboot: Booting Node 1, Processors #18 #19 #20 #21 #22 #23 But the last "OK" is lost, because 'nr_cpu_ids-1' represents the maximum possible cpu id. It should use the maximum present cpu id in case not all CPUs booted up. Signed-off-by: Libin <huawei.libin@huawei.com> Cc: <guohanjun@huawei.com> Cc: <wangyijing@huawei.com> Cc: <fenghua.yu@intel.com> Cc: <paul.gortmaker@windriver.com> Link: http://lkml.kernel.org/r/1378378676-18276-1-git-send-email-huawei.libin@huawei.com [ tweaked the changelog, removed unnecessary line break, tweaked the format to align the fields vertically. ] Signed-off-by: Ingo Molnar <mingo@kernel.org>

Hello, Jens. The original thread can be read from http://thread.gmane.org/gmane.linux.kernel.cgroups/8937 While it leads to oops, given that it only triggers under specific configurations which aren't common. I don't think it's necessary to backport it through -stable and merging it during the coming merge window should be enough. Thanks! ----- 8< ----- Currently, q->root_blkg and q->root_rl.blkg are set from blkcg_activate_policy() and cleared from blkg_destroy_all(). This doesn't necessarily coincide with the lifetime of the root blkcg_gq leading to the following oops when blkcg is enabled but no policy is activated because __blk_queue_next_rl() malfunctions expecting the root_blkg pointers to be set. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff810c58cb>] __wake_up_common+0x2b/0x90 PGD 60f7a9067 PUD 60f4c9067 PMD 0 Oops: 0000 [#1] SMP DEBUG_PAGEALLOC gsmi: Log Shutdown Reason 0x03 Modules linked in: act_mirred cls_tcindex cls_prioshift sch_dsmark xt_multiport iptable_mangle sata_mv elephant elephant_dev_num cdc_acm uhci_hcd ehci_hcd i2c_d CPU: 9 PID: 41382 Comm: iSCSI-write- Not tainted 3.11.0-dbg-DEV #19 Hardware name: Intel XXX task: ffff88060d16eec0 ti: ffff88060d170000 task.ti: ffff88060d170000 RIP: 0010:[<ffffffff810c58cb>] [<ffffffff810c58cb>] __wake_up_common+0x2b/0x90 RSP: 0000:ffff88060d171818 EFLAGS: 00010096 RAX: 0000000000000082 RBX: ffff880baa3dee60 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000003 RDI: ffff880baa3dee60 RBP: ffff88060d171858 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000002 R12: ffff880baa3dee98 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000003 FS: 00007f977cba6700(0000) GS:ffff880c79c60000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 000000060f7a5000 CR4: 00000000000007e0 Stack: 0000000000000082 0000000000000000 ffff88060d171858 ffff880baa3dee60 0000000000000082 0000000000000003 0000000000000000 0000000000000000 ffff88060d171898 ffffffff810c7848 ffff88060d171888 ffff880bde4bc4b8 Call Trace: [<ffffffff810c7848>] __wake_up+0x48/0x70 [<ffffffff8131da53>] __blk_drain_queue+0x123/0x190 [<ffffffff8131dbb5>] blk_cleanup_queue+0xf5/0x210 [<ffffffff8141877a>] __scsi_remove_device+0x5a/0xd0 [<ffffffff81418824>] scsi_remove_device+0x34/0x50 [<ffffffff814189cb>] scsi_remove_target+0x16b/0x220 [<ffffffff814210f1>] __iscsi_unbind_session+0xd1/0x1b0 [<ffffffff814212b2>] iscsi_remove_session+0xe2/0x1c0 [<ffffffff814213a6>] iscsi_destroy_session+0x16/0x60 [<ffffffff81423a59>] iscsi_session_teardown+0xd9/0x100 [<ffffffff8142b75a>] iscsi_sw_tcp_session_destroy+0x5a/0xb0 [<ffffffff81420948>] iscsi_if_rx+0x10e8/0x1560 [<ffffffff81573335>] netlink_unicast+0x145/0x200 [<ffffffff815736f3>] netlink_sendmsg+0x303/0x410 [<ffffffff81528196>] sock_sendmsg+0xa6/0xd0 [<ffffffff815294bc>] ___sys_sendmsg+0x38c/0x3a0 [<ffffffff811ea840>] ? fget_light+0x40/0x160 [<ffffffff811ea899>] ? fget_light+0x99/0x160 [<ffffffff811ea840>] ? fget_light+0x40/0x160 [<ffffffff8152bc79>] __sys_sendmsg+0x49/0x90 [<ffffffff8152bcd2>] SyS_sendmsg+0x12/0x20 [<ffffffff815fb642>] system_call_fastpath+0x16/0x1b Code: 66 66 66 66 90 55 48 89 e5 41 57 41 89 f7 41 56 41 89 ce 41 55 41 54 4c 8d 67 38 53 48 83 ec 18 89 55 c4 48 8b 57 38 4c 89 45 c8 <4c> 8b 2a 48 8d 42 e8 49 Fix it by moving r->root_blkg and q->root_rl.blkg setting to blkg_create() and clearing to blkg_destroy() so that they area initialized when a root blkg is created and cleared when destroyed. Reported-and-tested-by: Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>

The clk_init_data.flags of clk-fixup-mux is left there without initialization. It may hold some random data and cause clock framework interpret the clock in an unexpected way. At least on imx6sl, the following division by zero error with sched_clock is seen because of it. Division by zero in kernel. CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19 Backtrace: [<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c) r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000 [<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94) [<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20) r4:00000000 r3:00000000 [<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18) [<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0) [<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c) [<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0) r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000 [<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c) [<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18) r5:807a8e80 r4:ffffffff [<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34) [<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310) [<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074) r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms Fix the bug by initializing init.flags as zero. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

commit 42d64e1 upstream. The SELinux/NetLabel glue code has a locking bug that affects systems with NetLabel enabled, see the kernel error message below. This patch corrects this problem by converting the bottom half socket lock to a more conventional, and correct for this call-path, lock_sock() call. =============================== [ INFO: suspicious RCU usage. ] 3.11.0-rc3+ #19 Not tainted ------------------------------- net/ipv4/cipso_ipv4.c:1928 suspicious rcu_dereference_protected() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 2 locks held by ping/731: #0: (slock-AF_INET/1){+.-...}, at: [...] selinux_netlbl_socket_connect #1: (rcu_read_lock){.+.+..}, at: [<...>] netlbl_conn_setattr stack backtrace: CPU: 1 PID: 731 Comm: ping Not tainted 3.11.0-rc3+ #19 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000001 ffff88006f659d28 ffffffff81726b6a ffff88003732c500 ffff88006f659d58 ffffffff810e4457 ffff88006b845a00 0000000000000000 000000000000000c ffff880075aa2f50 ffff88006f659d90 ffffffff8169bec7 Call Trace: [<ffffffff81726b6a>] dump_stack+0x54/0x74 [<ffffffff810e4457>] lockdep_rcu_suspicious+0xe7/0x120 [<ffffffff8169bec7>] cipso_v4_sock_setattr+0x187/0x1a0 [<ffffffff8170f317>] netlbl_conn_setattr+0x187/0x190 [<ffffffff8170f195>] ? netlbl_conn_setattr+0x5/0x190 [<ffffffff8131ac9e>] selinux_netlbl_socket_connect+0xae/0xc0 [<ffffffff81303025>] selinux_socket_connect+0x135/0x170 [<ffffffff8119d127>] ? might_fault+0x57/0xb0 [<ffffffff812fb146>] security_socket_connect+0x16/0x20 [<ffffffff815d3ad3>] SYSC_connect+0x73/0x130 [<ffffffff81739a85>] ? sysret_check+0x22/0x5d [<ffffffff810e5e2d>] ? trace_hardirqs_on_caller+0xfd/0x1c0 [<ffffffff81373d4e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff815d52be>] SyS_connect+0xe/0x10 [<ffffffff81739a59>] system_call_fastpath+0x16/0x1b Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…is not present commit dc75925(OMAP: hwmod: Fix the missing braces) introduced missing braces, however, we just set return result if clk_get fail and we populate the error pointer in clk pointer and pass it along to clk_prepare. This is wrong. The intent seems to be retry remaining clocks if they are available and warn the ones we cant find clks for. With the current logic, we see the following crash: omap_hwmod: l3_main: cannot clk_get interface_clk emac_ick Unable to handle kernel NULL pointer dereference at virtual address 00000032 pgd = c0004000 [00000032] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc1-00044-gcc9fd5a-dirty #19 task: ce0c3440 ti: ce0c4000 task.ti: ce0c4000 PC is at __clk_prepare+0x10/0x74 LR is at clk_prepare+0x14/0x24 <snip> [<c044d59c>] (__clk_prepare+0x10/0x74) from [<c044d9b0>] (clk_prepare+0x14/0x24) [<c044d9b0>] (clk_prepare+0x14/0x24) from [<c077d8c4>] (_init+0x24c/0x3bc) [<c077d8c4>] (_init+0x24c/0x3bc) from [<c0027328>] (omap_hwmod_for_each+0x34/0x5c) [<c0027328>] (omap_hwmod_for_each+0x34/0x5c) from [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) [<c077dfa0>] (__omap_hwmod_setup_all+0x24/0x40) from [<c0008928>] (do_one_initcall+0x38/0x168) [<c0008928>] (do_one_initcall+0x38/0x168) from [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) [<c0771be8>] (kernel_init_freeable+0xfc/0x1cc) from [<c0521064>] (kernel_init+0x8/0x110) [<c0521064>] (kernel_init+0x8/0x110) from [<c000e568>] (ret_from_fork+0x14/0x2c) Code: e92d4038 e2504000 01a05004 0a000005 (e5943034) So, just warn and continue instead of proceeding and crashing, with missing clock nodes/bad data, we will eventually fail, however we should now have enough information to identify the culprit. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>

commit 3617f2c upstream. When a CPU is hot removed we'll cancel all the delayed work items via gov_cancel_work(). Normally this will just cancels a delayed timer on each CPU that the policy is managing and the work won't run, but if the work is already running the workqueue code will wait for the work to finish before continuing to prevent the work items from re-queuing themselves like they normally do. This scheme will work most of the time, except for the case where the work function determines that it should adjust the delay for all other CPUs that the policy is managing. If this scenario occurs, the canceling CPU will cancel its own work but queue up the other CPUs works to run. For example: CPU0 CPU1 ---- ---- cpu_down() ... __cpufreq_remove_dev() cpufreq_governor_dbs() case CPUFREQ_GOV_STOP: gov_cancel_work(dbs_data, policy); cpu0 work is canceled timer is canceled cpu1 work is canceled <work runs> <waits for cpu1> od_dbs_timer() gov_queue_work(*, *, true); cpu0 work queued cpu1 work queued cpu2 work queued ... cpu1 work is canceled cpu2 work is canceled ... At the end of the GOV_STOP case cpu0 still has a work queued to run although the code is expecting all of the works to be canceled. __cpufreq_remove_dev() will then proceed to re-initialize all the other CPUs works except for the CPU that is going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs() will trample over the queued work and debugobjects will spit out a warning: WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc() ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x10 Modules linked in: CPU: 0 PID: 1491 Comm: sh Tainted: G W 3.10.0 #19 [<c010c178>] (unwind_backtrace+0x0/0x11c) from [<c0109dec>] (show_stack+0x10/0x14) [<c0109dec>] (show_stack+0x10/0x14) from [<c01904cc>] (warn_slowpath_common+0x4c/0x6c) [<c01904cc>] (warn_slowpath_common+0x4c/0x6c) from [<c019056c>] (warn_slowpath_fmt+0x2c/0x3c) [<c019056c>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0388a7c>] (debug_print_object+0x94/0xbc) [<c0388a7c>] (debug_print_object+0x94/0xbc) from [<c0388e34>] (__debug_object_init+0x2d0/0x340) [<c0388e34>] (__debug_object_init+0x2d0/0x340) from [<c019e3b0>] (init_timer_key+0x14/0xb0) [<c019e3b0>] (init_timer_key+0x14/0xb0) from [<c0635f78>] (cpufreq_governor_dbs+0x3e8/0x5f8) [<c0635f78>] (cpufreq_governor_dbs+0x3e8/0x5f8) from [<c06325a0>] (__cpufreq_governor+0xdc/0x1a4) [<c06325a0>] (__cpufreq_governor+0xdc/0x1a4) from [<c0633704>] (__cpufreq_remove_dev.isra.10+0x3b4/0x434) [<c0633704>] (__cpufreq_remove_dev.isra.10+0x3b4/0x434) from [<c08989f4>] (cpufreq_cpu_callback+0x60/0x80) [<c08989f4>] (cpufreq_cpu_callback+0x60/0x80) from [<c08a43c0>] (notifier_call_chain+0x38/0x68) [<c08a43c0>] (notifier_call_chain+0x38/0x68) from [<c01938e0>] (__cpu_notify+0x28/0x40) [<c01938e0>] (__cpu_notify+0x28/0x40) from [<c0892ad4>] (_cpu_down+0x7c/0x2c0) [<c0892ad4>] (_cpu_down+0x7c/0x2c0) from [<c0892d3c>] (cpu_down+0x24/0x40) [<c0892d3c>] (cpu_down+0x24/0x40) from [<c0893ea8>] (store_online+0x2c/0x74) [<c0893ea8>] (store_online+0x2c/0x74) from [<c04519d8>] (dev_attr_store+0x18/0x24) [<c04519d8>] (dev_attr_store+0x18/0x24) from [<c02a69d4>] (sysfs_write_file+0x100/0x148) [<c02a69d4>] (sysfs_write_file+0x100/0x148) from [<c0255c18>] (vfs_write+0xcc/0x174) [<c0255c18>] (vfs_write+0xcc/0x174) from [<c0255f70>] (SyS_write+0x38/0x64) [<c0255f70>] (SyS_write+0x38/0x64) from [<c0106120>] (ret_fast_syscall+0x0/0x30) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0b0747d upstream. The following processes run into a deadlock. CPU 41 was waiting for CPU 29 to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29 was hung by that spinlock with IRQs disabled. PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd" !# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0 !# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0 !# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0 # 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0 # 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0 # 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0 # 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0 # 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0 # 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0 # 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0 #10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0 #11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0 #12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0 #13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0 #14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0 #15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0 #16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0 #17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0 #18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0 #19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 #20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 #21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 #22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 #23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 #24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 #25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 #26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 #27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd" !# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0 !# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0 # 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0 # 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0 # 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0 # 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0 # 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0 # 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0 # 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0 # 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 #10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 #11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 #12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 #13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 #14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 #15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 #16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 #17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 The lock is used to synchronize different sysfs operations, it doesn't protect any resource that will be touched by an interrupt. Consequently it's not required to disable IRQs. Replace the spinlock with a mutex to fix the deadlock. Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230828221018.19471-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The following call trace shows a deadlock issue due to recursive locking of mutex "device_mutex". First lock acquire is in target_for_each_device() and second in target_free_device(). PID: 148266 TASK: ffff8be21ffb5d00 CPU: 10 COMMAND: "iscsi_ttx" #0 [ffffa2bfc9ec3b18] __schedule at ffffffffa8060e7f #1 [ffffa2bfc9ec3ba0] schedule at ffffffffa8061224 #2 [ffffa2bfc9ec3bb8] schedule_preempt_disabled at ffffffffa80615ee #3 [ffffa2bfc9ec3bc8] __mutex_lock at ffffffffa8062fd7 #4 [ffffa2bfc9ec3c40] __mutex_lock_slowpath at ffffffffa80631d3 #5 [ffffa2bfc9ec3c50] mutex_lock at ffffffffa806320c #6 [ffffa2bfc9ec3c68] target_free_device at ffffffffc0935998 [target_core_mod] #7 [ffffa2bfc9ec3c90] target_core_dev_release at ffffffffc092f975 [target_core_mod] #8 [ffffa2bfc9ec3ca0] config_item_put at ffffffffa79d250f #9 [ffffa2bfc9ec3cd0] config_item_put at ffffffffa79d2583 #10 [ffffa2bfc9ec3ce0] target_devices_idr_iter at ffffffffc0933f3a [target_core_mod] #11 [ffffa2bfc9ec3d00] idr_for_each at ffffffffa803f6fc #12 [ffffa2bfc9ec3d60] target_for_each_device at ffffffffc0935670 [target_core_mod] #13 [ffffa2bfc9ec3d98] transport_deregister_session at ffffffffc0946408 [target_core_mod] #14 [ffffa2bfc9ec3dc8] iscsit_close_session at ffffffffc09a44a6 [iscsi_target_mod] #15 [ffffa2bfc9ec3df0] iscsit_close_connection at ffffffffc09a4a88 [iscsi_target_mod] #16 [ffffa2bfc9ec3df8] finish_task_switch at ffffffffa76e5d07 #17 [ffffa2bfc9ec3e78] iscsit_take_action_for_connection_exit at ffffffffc0991c23 [iscsi_target_mod] #18 [ffffa2bfc9ec3ea0] iscsi_target_tx_thread at ffffffffc09a403b [iscsi_target_mod] #19 [ffffa2bfc9ec3f08] kthread at ffffffffa76d8080 #20 [ffffa2bfc9ec3f50] ret_from_fork at ffffffffa8200364 Fixes: 36d4cb4 ("scsi: target: Avoid that EXTENDED COPY commands trigger lock inversion") Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230918225848.66463-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

commit 0b0747d upstream. The following processes run into a deadlock. CPU 41 was waiting for CPU 29 to handle a CSD request while holding spinlock "crashdump_lock", but CPU 29 was hung by that spinlock with IRQs disabled. PID: 17360 TASK: ffff95c1090c5c40 CPU: 41 COMMAND: "mrdiagd" !# 0 [ffffb80edbf37b58] __read_once_size at ffffffff9b871a40 include/linux/compiler.h:185:0 !# 1 [ffffb80edbf37b58] atomic_read at ffffffff9b871a40 arch/x86/include/asm/atomic.h:27:0 !# 2 [ffffb80edbf37b58] dump_stack at ffffffff9b871a40 lib/dump_stack.c:54:0 # 3 [ffffb80edbf37b78] csd_lock_wait_toolong at ffffffff9b131ad5 kernel/smp.c:364:0 # 4 [ffffb80edbf37b78] __csd_lock_wait at ffffffff9b131ad5 kernel/smp.c:384:0 # 5 [ffffb80edbf37bf8] csd_lock_wait at ffffffff9b13267a kernel/smp.c:394:0 # 6 [ffffb80edbf37bf8] smp_call_function_many at ffffffff9b13267a kernel/smp.c:843:0 # 7 [ffffb80edbf37c50] smp_call_function at ffffffff9b13279d kernel/smp.c:867:0 # 8 [ffffb80edbf37c50] on_each_cpu at ffffffff9b13279d kernel/smp.c:976:0 # 9 [ffffb80edbf37c78] flush_tlb_kernel_range at ffffffff9b085c4b arch/x86/mm/tlb.c:742:0 raspberrypi#10 [ffffb80edbf37cb8] __purge_vmap_area_lazy at ffffffff9b23a1e0 mm/vmalloc.c:701:0 raspberrypi#11 [ffffb80edbf37ce0] try_purge_vmap_area_lazy at ffffffff9b23a2cc mm/vmalloc.c:722:0 raspberrypi#12 [ffffb80edbf37ce0] free_vmap_area_noflush at ffffffff9b23a2cc mm/vmalloc.c:754:0 raspberrypi#13 [ffffb80edbf37cf8] free_unmap_vmap_area at ffffffff9b23bb3b mm/vmalloc.c:764:0 raspberrypi#14 [ffffb80edbf37cf8] remove_vm_area at ffffffff9b23bb3b mm/vmalloc.c:1509:0 raspberrypi#15 [ffffb80edbf37d18] __vunmap at ffffffff9b23bb8a mm/vmalloc.c:1537:0 raspberrypi#16 [ffffb80edbf37d40] vfree at ffffffff9b23bc85 mm/vmalloc.c:1612:0 raspberrypi#17 [ffffb80edbf37d58] megasas_free_host_crash_buffer [megaraid_sas] at ffffffffc020b7f2 drivers/scsi/megaraid/megaraid_sas_fusion.c:3932:0 raspberrypi#18 [ffffb80edbf37d80] fw_crash_state_store [megaraid_sas] at ffffffffc01f804d drivers/scsi/megaraid/megaraid_sas_base.c:3291:0 raspberrypi#19 [ffffb80edbf37dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 raspberrypi#20 [ffffb80edbf37dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 raspberrypi#21 [ffffb80edbf37de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 raspberrypi#22 [ffffb80edbf37e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 raspberrypi#23 [ffffb80edbf37ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 raspberrypi#24 [ffffb80edbf37ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 raspberrypi#25 [ffffb80edbf37ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 raspberrypi#26 [ffffb80edbf37f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 raspberrypi#27 [ffffb80edbf37f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 PID: 17355 TASK: ffff95c1090c3d80 CPU: 29 COMMAND: "mrdiagd" !# 0 [ffffb80f2d3c7d30] __read_once_size at ffffffff9b0f2ab0 include/linux/compiler.h:185:0 !# 1 [ffffb80f2d3c7d30] native_queued_spin_lock_slowpath at ffffffff9b0f2ab0 kernel/locking/qspinlock.c:368:0 # 2 [ffffb80f2d3c7d58] pv_queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/paravirt.h:674:0 # 3 [ffffb80f2d3c7d58] queued_spin_lock_slowpath at ffffffff9b0f244b arch/x86/include/asm/qspinlock.h:53:0 # 4 [ffffb80f2d3c7d68] queued_spin_lock at ffffffff9b8961a6 include/asm-generic/qspinlock.h:90:0 # 5 [ffffb80f2d3c7d68] do_raw_spin_lock_flags at ffffffff9b8961a6 include/linux/spinlock.h:173:0 # 6 [ffffb80f2d3c7d68] __raw_spin_lock_irqsave at ffffffff9b8961a6 include/linux/spinlock_api_smp.h:122:0 # 7 [ffffb80f2d3c7d68] _raw_spin_lock_irqsave at ffffffff9b8961a6 kernel/locking/spinlock.c:160:0 # 8 [ffffb80f2d3c7d88] fw_crash_buffer_store [megaraid_sas] at ffffffffc01f8129 drivers/scsi/megaraid/megaraid_sas_base.c:3205:0 # 9 [ffffb80f2d3c7dc0] dev_attr_store at ffffffff9b56dd7b drivers/base/core.c:758:0 raspberrypi#10 [ffffb80f2d3c7dd0] sysfs_kf_write at ffffffff9b326acf fs/sysfs/file.c:144:0 raspberrypi#11 [ffffb80f2d3c7de0] kernfs_fop_write at ffffffff9b325fd4 fs/kernfs/file.c:316:0 raspberrypi#12 [ffffb80f2d3c7e20] __vfs_write at ffffffff9b29418a fs/read_write.c:480:0 raspberrypi#13 [ffffb80f2d3c7ea8] vfs_write at ffffffff9b294462 fs/read_write.c:544:0 raspberrypi#14 [ffffb80f2d3c7ee8] SYSC_write at ffffffff9b2946ec fs/read_write.c:590:0 raspberrypi#15 [ffffb80f2d3c7ee8] SyS_write at ffffffff9b2946ec fs/read_write.c:582:0 raspberrypi#16 [ffffb80f2d3c7f30] do_syscall_64 at ffffffff9b003ca9 arch/x86/entry/common.c:298:0 raspberrypi#17 [ffffb80f2d3c7f58] entry_SYSCALL_64 at ffffffff9ba001b1 arch/x86/entry/entry_64.S:238:0 The lock is used to synchronize different sysfs operations, it doesn't protect any resource that will be touched by an interrupt. Consequently it's not required to disable IRQs. Replace the spinlock with a mutex to fix the deadlock. Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230828221018.19471-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a154f5f ] The following call trace shows a deadlock issue due to recursive locking of mutex "device_mutex". First lock acquire is in target_for_each_device() and second in target_free_device(). PID: 148266 TASK: ffff8be21ffb5d00 CPU: 10 COMMAND: "iscsi_ttx" #0 [ffffa2bfc9ec3b18] __schedule at ffffffffa8060e7f #1 [ffffa2bfc9ec3ba0] schedule at ffffffffa8061224 #2 [ffffa2bfc9ec3bb8] schedule_preempt_disabled at ffffffffa80615ee #3 [ffffa2bfc9ec3bc8] __mutex_lock at ffffffffa8062fd7 #4 [ffffa2bfc9ec3c40] __mutex_lock_slowpath at ffffffffa80631d3 #5 [ffffa2bfc9ec3c50] mutex_lock at ffffffffa806320c #6 [ffffa2bfc9ec3c68] target_free_device at ffffffffc0935998 [target_core_mod] #7 [ffffa2bfc9ec3c90] target_core_dev_release at ffffffffc092f975 [target_core_mod] #8 [ffffa2bfc9ec3ca0] config_item_put at ffffffffa79d250f #9 [ffffa2bfc9ec3cd0] config_item_put at ffffffffa79d2583 #10 [ffffa2bfc9ec3ce0] target_devices_idr_iter at ffffffffc0933f3a [target_core_mod] #11 [ffffa2bfc9ec3d00] idr_for_each at ffffffffa803f6fc #12 [ffffa2bfc9ec3d60] target_for_each_device at ffffffffc0935670 [target_core_mod] #13 [ffffa2bfc9ec3d98] transport_deregister_session at ffffffffc0946408 [target_core_mod] #14 [ffffa2bfc9ec3dc8] iscsit_close_session at ffffffffc09a44a6 [iscsi_target_mod] #15 [ffffa2bfc9ec3df0] iscsit_close_connection at ffffffffc09a4a88 [iscsi_target_mod] #16 [ffffa2bfc9ec3df8] finish_task_switch at ffffffffa76e5d07 #17 [ffffa2bfc9ec3e78] iscsit_take_action_for_connection_exit at ffffffffc0991c23 [iscsi_target_mod] #18 [ffffa2bfc9ec3ea0] iscsi_target_tx_thread at ffffffffc09a403b [iscsi_target_mod] #19 [ffffa2bfc9ec3f08] kthread at ffffffffa76d8080 #20 [ffffa2bfc9ec3f50] ret_from_fork at ffffffffa8200364 Fixes: 36d4cb4 ("scsi: target: Avoid that EXTENDED COPY commands trigger lock inversion") Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Link: https://lore.kernel.org/r/20230918225848.66463-1-junxiao.bi@oracle.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be dereferenced as wrong struct in irdma_free_pending_cqp_request(). PID: 3669 TASK: ffff88aef892c000 CPU: 28 COMMAND: "kworker/28:0" #0 [fffffe0000549e38] crash_nmi_callback at ffffffff810e3a34 #1 [fffffe0000549e40] nmi_handle at ffffffff810788b2 #2 [fffffe0000549ea0] default_do_nmi at ffffffff8107938f #3 [fffffe0000549eb8] do_nmi at ffffffff81079582 #4 [fffffe0000549ef0] end_repeat_nmi at ffffffff82e016b4 [exception RIP: native_queued_spin_lock_slowpath+1291] RIP: ffffffff8127e72b RSP: ffff88aa841ef778 RFLAGS: 00000046 RAX: 0000000000000000 RBX: ffff88b01f849700 RCX: ffffffff8127e47e RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff83857ec0 RBP: ffff88afe3e4efc8 R8: ffffed15fc7c9dfa R9: ffffed15fc7c9dfa R10: 0000000000000001 R11: ffffed15fc7c9df9 R12: 0000000000740000 R13: ffff88b01f849708 R14: 0000000000000003 R15: ffffed1603f092e1 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 -- <NMI exception stack> -- #5 [ffff88aa841ef778] native_queued_spin_lock_slowpath at ffffffff8127e72b #6 [ffff88aa841ef7b0] _raw_spin_lock_irqsave at ffffffff82c22aa4 #7 [ffff88aa841ef7c8] __wake_up_common_lock at ffffffff81257363 #8 [ffff88aa841ef888] irdma_free_pending_cqp_request at ffffffffa0ba12cc [irdma] #9 [ffff88aa841ef958] irdma_cleanup_pending_cqp_op at ffffffffa0ba1469 [irdma] #10 [ffff88aa841ef9c0] irdma_ctrl_deinit_hw at ffffffffa0b2989f [irdma] #11 [ffff88aa841efa28] irdma_remove at ffffffffa0b252df [irdma] #12 [ffff88aa841efae8] auxiliary_bus_remove at ffffffff8219afdb #13 [ffff88aa841efb00] device_release_driver_internal at ffffffff821882e6 #14 [ffff88aa841efb38] bus_remove_device at ffffffff82184278 #15 [ffff88aa841efb88] device_del at ffffffff82179d23 #16 [ffff88aa841efc48] ice_unplug_aux_dev at ffffffffa0eb1c14 [ice] #17 [ffff88aa841efc68] ice_service_task at ffffffffa0d88201 [ice] #18 [ffff88aa841efde8] process_one_work at ffffffff811c589a #19 [ffff88aa841efe60] worker_thread at ffffffff811c71ff #20 [ffff88aa841eff10] kthread at ffffffff811d87a0 #21 [ffff88aa841eff50] ret_from_fork at ffffffff82e0022f Fixes: 44d9e52 ("RDMA/irdma: Implement device initialization definitions") Link: https://lore.kernel.org/r/20231130081415.891006-1-lishifeng@sangfor.com.cn Suggested-by: "Ismail, Mustafa" <mustafa.ismail@intel.com> Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn> Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>

[ Upstream commit e3e82fc ] When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be dereferenced as wrong struct in irdma_free_pending_cqp_request(). PID: 3669 TASK: ffff88aef892c000 CPU: 28 COMMAND: "kworker/28:0" #0 [fffffe0000549e38] crash_nmi_callback at ffffffff810e3a34 #1 [fffffe0000549e40] nmi_handle at ffffffff810788b2 #2 [fffffe0000549ea0] default_do_nmi at ffffffff8107938f #3 [fffffe0000549eb8] do_nmi at ffffffff81079582 #4 [fffffe0000549ef0] end_repeat_nmi at ffffffff82e016b4 [exception RIP: native_queued_spin_lock_slowpath+1291] RIP: ffffffff8127e72b RSP: ffff88aa841ef778 RFLAGS: 00000046 RAX: 0000000000000000 RBX: ffff88b01f849700 RCX: ffffffff8127e47e RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff83857ec0 RBP: ffff88afe3e4efc8 R8: ffffed15fc7c9dfa R9: ffffed15fc7c9dfa R10: 0000000000000001 R11: ffffed15fc7c9df9 R12: 0000000000740000 R13: ffff88b01f849708 R14: 0000000000000003 R15: ffffed1603f092e1 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 -- <NMI exception stack> -- #5 [ffff88aa841ef778] native_queued_spin_lock_slowpath at ffffffff8127e72b #6 [ffff88aa841ef7b0] _raw_spin_lock_irqsave at ffffffff82c22aa4 #7 [ffff88aa841ef7c8] __wake_up_common_lock at ffffffff81257363 #8 [ffff88aa841ef888] irdma_free_pending_cqp_request at ffffffffa0ba12cc [irdma] #9 [ffff88aa841ef958] irdma_cleanup_pending_cqp_op at ffffffffa0ba1469 [irdma] #10 [ffff88aa841ef9c0] irdma_ctrl_deinit_hw at ffffffffa0b2989f [irdma] #11 [ffff88aa841efa28] irdma_remove at ffffffffa0b252df [irdma] #12 [ffff88aa841efae8] auxiliary_bus_remove at ffffffff8219afdb #13 [ffff88aa841efb00] device_release_driver_internal at ffffffff821882e6 #14 [ffff88aa841efb38] bus_remove_device at ffffffff82184278 #15 [ffff88aa841efb88] device_del at ffffffff82179d23 #16 [ffff88aa841efc48] ice_unplug_aux_dev at ffffffffa0eb1c14 [ice] #17 [ffff88aa841efc68] ice_service_task at ffffffffa0d88201 [ice] #18 [ffff88aa841efde8] process_one_work at ffffffff811c589a #19 [ffff88aa841efe60] worker_thread at ffffffff811c71ff #20 [ffff88aa841eff10] kthread at ffffffff811d87a0 #21 [ffff88aa841eff50] ret_from_fork at ffffffff82e0022f Fixes: 44d9e52 ("RDMA/irdma: Implement device initialization definitions") Link: https://lore.kernel.org/r/20231130081415.891006-1-lishifeng@sangfor.com.cn Suggested-by: "Ismail, Mustafa" <mustafa.ismail@intel.com> Signed-off-by: Shifeng Li <lishifeng@sangfor.com.cn> Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e8a1e58 ] mac802154_llsec_key_del() can free resources of a key directly without following the RCU rules for waiting before the end of a grace period. This may lead to use-after-free in case llsec_lookup_key() is traversing the list of keys in parallel with a key deletion: refcount_t: addition on 0; use-after-free. WARNING: CPU: 4 PID: 16000 at lib/refcount.c:25 refcount_warn_saturate+0x162/0x2a0 Modules linked in: CPU: 4 PID: 16000 Comm: wpan-ping Not tainted 6.7.0 #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:refcount_warn_saturate+0x162/0x2a0 Call Trace: <TASK> llsec_lookup_key.isra.0+0x890/0x9e0 mac802154_llsec_encrypt+0x30c/0x9c0 ieee802154_subif_start_xmit+0x24/0x1e0 dev_hard_start_xmit+0x13e/0x690 sch_direct_xmit+0x2ae/0xbc0 __dev_queue_xmit+0x11dd/0x3c20 dgram_sendmsg+0x90b/0xd60 __sys_sendto+0x466/0x4c0 __x64_sys_sendto+0xe0/0x1c0 do_syscall_64+0x45/0xf0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 Also, ieee802154_llsec_key_entry structures are not freed by mac802154_llsec_key_del(): unreferenced object 0xffff8880613b6980 (size 64): comm "iwpan", pid 2176, jiffies 4294761134 (age 60.475s) hex dump (first 32 bytes): 78 0d 8f 18 80 88 ff ff 22 01 00 00 00 00 ad de x......."....... 00 00 00 00 00 00 00 00 03 00 cd ab 00 00 00 00 ................ backtrace: [<ffffffff81dcfa62>] __kmem_cache_alloc_node+0x1e2/0x2d0 [<ffffffff81c43865>] kmalloc_trace+0x25/0xc0 [<ffffffff88968b09>] mac802154_llsec_key_add+0xac9/0xcf0 [<ffffffff8896e41a>] ieee802154_add_llsec_key+0x5a/0x80 [<ffffffff8892adc6>] nl802154_add_llsec_key+0x426/0x5b0 [<ffffffff86ff293e>] genl_family_rcv_msg_doit+0x1fe/0x2f0 [<ffffffff86ff46d1>] genl_rcv_msg+0x531/0x7d0 [<ffffffff86fee7a9>] netlink_rcv_skb+0x169/0x440 [<ffffffff86ff1d88>] genl_rcv+0x28/0x40 [<ffffffff86fec15c>] netlink_unicast+0x53c/0x820 [<ffffffff86fecd8b>] netlink_sendmsg+0x93b/0xe60 [<ffffffff86b91b35>] ____sys_sendmsg+0xac5/0xca0 [<ffffffff86b9c3dd>] ___sys_sendmsg+0x11d/0x1c0 [<ffffffff86b9c65a>] __sys_sendmsg+0xfa/0x1d0 [<ffffffff88eadbf5>] do_syscall_64+0x45/0xf0 [<ffffffff890000ea>] entry_SYSCALL_64_after_hwframe+0x6e/0x76 Handle the proper resource release in the RCU callback function mac802154_llsec_key_del_rcu(). Note that if llsec_lookup_key() finds a key, it gets a refcount via llsec_key_get() and locally copies key id from key_entry (which is a list element). So it's safe to call llsec_key_put() and free the list entry after the RCU grace period elapses. Found by Linux Verification Center (linuxtesting.org). Fixes: 5d637d5 ("mac802154: add llsec structures and mutators") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Alexander Aring <aahringo@redhat.com> Message-ID: <20240228163840.6667-1-pchelkin@ispras.ru> Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

For historical reasons, when bridge device is in promisc mode, packets that are directed to the taps follow bridge input hook path. This patch adds a workaround to reset conntrack for these packets. Jianbo Liu reports warning splats in their test infrastructure where cloned packets reach the br_netfilter input hook to confirm the conntrack object. Scratch one bit from BR_INPUT_SKB_CB to annotate that this packet has reached the input hook because it is passed up to the bridge device to reach the taps. [ 57.571874] WARNING: CPU: 1 PID: 0 at net/bridge/br_netfilter_hooks.c:616 br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.572749] Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_isc si ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5ctl mlx5_core [ 57.575158] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0+ #19 [ 57.575700] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 57.576662] RIP: 0010:br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.577195] Code: fe ff ff 41 bd 04 00 00 00 be 04 00 00 00 e9 4a ff ff ff be 04 00 00 00 48 89 ef e8 f3 a9 3c e1 66 83 ad b4 00 00 00 04 eb 91 <0f> 0b e9 f1 fe ff ff 0f 0b e9 df fe ff ff 48 89 df e8 b3 53 47 e1 [ 57.578722] RSP: 0018:ffff88885f845a08 EFLAGS: 00010202 [ 57.579207] RAX: 0000000000000002 RBX: ffff88812dfe8000 RCX: 0000000000000000 [ 57.579830] RDX: ffff88885f845a60 RSI: ffff8881022dc300 RDI: 0000000000000000 [ 57.580454] RBP: ffff88885f845a60 R08: 0000000000000001 R09: 0000000000000003 [ 57.581076] R10: 00000000ffff1300 R11: 0000000000000002 R12: 0000000000000000 [ 57.581695] R13: ffff8881047ffe00 R14: ffff888108dbee00 R15: ffff88814519b800 [ 57.582313] FS: 0000000000000000(0000) GS:ffff88885f840000(0000) knlGS:0000000000000000 [ 57.583040] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.583564] CR2: 000000c4206aa000 CR3: 0000000103847001 CR4: 0000000000370eb0 [ 57.584194] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.584820] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.585440] Call Trace: [ 57.585721] <IRQ> [ 57.585976] ? __warn+0x7d/0x130 [ 57.586323] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.586811] ? report_bug+0xf1/0x1c0 [ 57.587177] ? handle_bug+0x3f/0x70 [ 57.587539] ? exc_invalid_op+0x13/0x60 [ 57.587929] ? asm_exc_invalid_op+0x16/0x20 [ 57.588336] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.588825] nf_hook_slow+0x3d/0xd0 [ 57.589188] ? br_handle_vlan+0x4b/0x110 [ 57.589579] br_pass_frame_up+0xfc/0x150 [ 57.589970] ? br_port_flags_change+0x40/0x40 [ 57.590396] br_handle_frame_finish+0x346/0x5e0 [ 57.590837] ? ipt_do_table+0x32e/0x430 [ 57.591221] ? br_handle_local_finish+0x20/0x20 [ 57.591656] br_nf_hook_thresh+0x4b/0xf0 [br_netfilter] [ 57.592286] ? br_handle_local_finish+0x20/0x20 [ 57.592802] br_nf_pre_routing_finish+0x178/0x480 [br_netfilter] [ 57.593348] ? br_handle_local_finish+0x20/0x20 [ 57.593782] ? nf_nat_ipv4_pre_routing+0x25/0x60 [nf_nat] [ 57.594279] br_nf_pre_routing+0x24c/0x550 [br_netfilter] [ 57.594780] ? br_nf_hook_thresh+0xf0/0xf0 [br_netfilter] [ 57.595280] br_handle_frame+0x1f3/0x3d0 [ 57.595676] ? br_handle_local_finish+0x20/0x20 [ 57.596118] ? br_handle_frame_finish+0x5e0/0x5e0 [ 57.596566] __netif_receive_skb_core+0x25b/0xfc0 [ 57.597017] ? __napi_build_skb+0x37/0x40 [ 57.597418] __netif_receive_skb_list_core+0xfb/0x220 Fixes: 62e7151 ("netfilter: bridge: confirm multicast packets before passing them up the stack") Reported-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <lei.chen@smartx.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

[ Upstream commit 751de20 ] For historical reasons, when bridge device is in promisc mode, packets that are directed to the taps follow bridge input hook path. This patch adds a workaround to reset conntrack for these packets. Jianbo Liu reports warning splats in their test infrastructure where cloned packets reach the br_netfilter input hook to confirm the conntrack object. Scratch one bit from BR_INPUT_SKB_CB to annotate that this packet has reached the input hook because it is passed up to the bridge device to reach the taps. [ 57.571874] WARNING: CPU: 1 PID: 0 at net/bridge/br_netfilter_hooks.c:616 br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.572749] Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_isc si ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5ctl mlx5_core [ 57.575158] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0+ #19 [ 57.575700] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 57.576662] RIP: 0010:br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.577195] Code: fe ff ff 41 bd 04 00 00 00 be 04 00 00 00 e9 4a ff ff ff be 04 00 00 00 48 89 ef e8 f3 a9 3c e1 66 83 ad b4 00 00 00 04 eb 91 <0f> 0b e9 f1 fe ff ff 0f 0b e9 df fe ff ff 48 89 df e8 b3 53 47 e1 [ 57.578722] RSP: 0018:ffff88885f845a08 EFLAGS: 00010202 [ 57.579207] RAX: 0000000000000002 RBX: ffff88812dfe8000 RCX: 0000000000000000 [ 57.579830] RDX: ffff88885f845a60 RSI: ffff8881022dc300 RDI: 0000000000000000 [ 57.580454] RBP: ffff88885f845a60 R08: 0000000000000001 R09: 0000000000000003 [ 57.581076] R10: 00000000ffff1300 R11: 0000000000000002 R12: 0000000000000000 [ 57.581695] R13: ffff8881047ffe00 R14: ffff888108dbee00 R15: ffff88814519b800 [ 57.582313] FS: 0000000000000000(0000) GS:ffff88885f840000(0000) knlGS:0000000000000000 [ 57.583040] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.583564] CR2: 000000c4206aa000 CR3: 0000000103847001 CR4: 0000000000370eb0 [ 57.584194] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.584820] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.585440] Call Trace: [ 57.585721] <IRQ> [ 57.585976] ? __warn+0x7d/0x130 [ 57.586323] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.586811] ? report_bug+0xf1/0x1c0 [ 57.587177] ? handle_bug+0x3f/0x70 [ 57.587539] ? exc_invalid_op+0x13/0x60 [ 57.587929] ? asm_exc_invalid_op+0x16/0x20 [ 57.588336] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.588825] nf_hook_slow+0x3d/0xd0 [ 57.589188] ? br_handle_vlan+0x4b/0x110 [ 57.589579] br_pass_frame_up+0xfc/0x150 [ 57.589970] ? br_port_flags_change+0x40/0x40 [ 57.590396] br_handle_frame_finish+0x346/0x5e0 [ 57.590837] ? ipt_do_table+0x32e/0x430 [ 57.591221] ? br_handle_local_finish+0x20/0x20 [ 57.591656] br_nf_hook_thresh+0x4b/0xf0 [br_netfilter] [ 57.592286] ? br_handle_local_finish+0x20/0x20 [ 57.592802] br_nf_pre_routing_finish+0x178/0x480 [br_netfilter] [ 57.593348] ? br_handle_local_finish+0x20/0x20 [ 57.593782] ? nf_nat_ipv4_pre_routing+0x25/0x60 [nf_nat] [ 57.594279] br_nf_pre_routing+0x24c/0x550 [br_netfilter] [ 57.594780] ? br_nf_hook_thresh+0xf0/0xf0 [br_netfilter] [ 57.595280] br_handle_frame+0x1f3/0x3d0 [ 57.595676] ? br_handle_local_finish+0x20/0x20 [ 57.596118] ? br_handle_frame_finish+0x5e0/0x5e0 [ 57.596566] __netif_receive_skb_core+0x25b/0xfc0 [ 57.597017] ? __napi_build_skb+0x37/0x40 [ 57.597418] __netif_receive_skb_list_core+0xfb/0x220 Fixes: 62e7151 ("netfilter: bridge: confirm multicast packets before passing them up the stack") Reported-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f8bbc07 ] vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <lei.chen@smartx.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 751de20 ] For historical reasons, when bridge device is in promisc mode, packets that are directed to the taps follow bridge input hook path. This patch adds a workaround to reset conntrack for these packets. Jianbo Liu reports warning splats in their test infrastructure where cloned packets reach the br_netfilter input hook to confirm the conntrack object. Scratch one bit from BR_INPUT_SKB_CB to annotate that this packet has reached the input hook because it is passed up to the bridge device to reach the taps. [ 57.571874] WARNING: CPU: 1 PID: 0 at net/bridge/br_netfilter_hooks.c:616 br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.572749] Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_isc si ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5ctl mlx5_core [ 57.575158] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0+ #19 [ 57.575700] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 57.576662] RIP: 0010:br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.577195] Code: fe ff ff 41 bd 04 00 00 00 be 04 00 00 00 e9 4a ff ff ff be 04 00 00 00 48 89 ef e8 f3 a9 3c e1 66 83 ad b4 00 00 00 04 eb 91 <0f> 0b e9 f1 fe ff ff 0f 0b e9 df fe ff ff 48 89 df e8 b3 53 47 e1 [ 57.578722] RSP: 0018:ffff88885f845a08 EFLAGS: 00010202 [ 57.579207] RAX: 0000000000000002 RBX: ffff88812dfe8000 RCX: 0000000000000000 [ 57.579830] RDX: ffff88885f845a60 RSI: ffff8881022dc300 RDI: 0000000000000000 [ 57.580454] RBP: ffff88885f845a60 R08: 0000000000000001 R09: 0000000000000003 [ 57.581076] R10: 00000000ffff1300 R11: 0000000000000002 R12: 0000000000000000 [ 57.581695] R13: ffff8881047ffe00 R14: ffff888108dbee00 R15: ffff88814519b800 [ 57.582313] FS: 0000000000000000(0000) GS:ffff88885f840000(0000) knlGS:0000000000000000 [ 57.583040] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 57.583564] CR2: 000000c4206aa000 CR3: 0000000103847001 CR4: 0000000000370eb0 [ 57.584194] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 57.584820] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 57.585440] Call Trace: [ 57.585721] <IRQ> [ 57.585976] ? __warn+0x7d/0x130 [ 57.586323] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.586811] ? report_bug+0xf1/0x1c0 [ 57.587177] ? handle_bug+0x3f/0x70 [ 57.587539] ? exc_invalid_op+0x13/0x60 [ 57.587929] ? asm_exc_invalid_op+0x16/0x20 [ 57.588336] ? br_nf_local_in+0x157/0x180 [br_netfilter] [ 57.588825] nf_hook_slow+0x3d/0xd0 [ 57.589188] ? br_handle_vlan+0x4b/0x110 [ 57.589579] br_pass_frame_up+0xfc/0x150 [ 57.589970] ? br_port_flags_change+0x40/0x40 [ 57.590396] br_handle_frame_finish+0x346/0x5e0 [ 57.590837] ? ipt_do_table+0x32e/0x430 [ 57.591221] ? br_handle_local_finish+0x20/0x20 [ 57.591656] br_nf_hook_thresh+0x4b/0xf0 [br_netfilter] [ 57.592286] ? br_handle_local_finish+0x20/0x20 [ 57.592802] br_nf_pre_routing_finish+0x178/0x480 [br_netfilter] [ 57.593348] ? br_handle_local_finish+0x20/0x20 [ 57.593782] ? nf_nat_ipv4_pre_routing+0x25/0x60 [nf_nat] [ 57.594279] br_nf_pre_routing+0x24c/0x550 [br_netfilter] [ 57.594780] ? br_nf_hook_thresh+0xf0/0xf0 [br_netfilter] [ 57.595280] br_handle_frame+0x1f3/0x3d0 [ 57.595676] ? br_handle_local_finish+0x20/0x20 [ 57.596118] ? br_handle_frame_finish+0x5e0/0x5e0 [ 57.596566] __netif_receive_skb_core+0x25b/0xfc0 [ 57.597017] ? __napi_build_skb+0x37/0x40 [ 57.597418] __netif_receive_skb_list_core+0xfb/0x220 Fixes: 62e7151 ("netfilter: bridge: confirm multicast packets before passing them up the stack") Reported-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f8bbc07 ] vhost_worker will call tun call backs to receive packets. If too many illegal packets arrives, tun_do_read will keep dumping packet contents. When console is enabled, it will costs much more cpu time to dump packet and soft lockup will be detected. net_ratelimit mechanism can be used to limit the dumping rate. PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980" #0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253 #1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3 #2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e #3 [fffffe00003fced0] do_nmi at ffffffff8922660d #4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663 [exception RIP: io_serial_in+20] RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002 RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000 RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0 RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020 R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #5 [ffffa655314979e8] io_serial_in at ffffffff89792594 #6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470 #7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6 #8 [ffffa65531497a20] uart_console_write at ffffffff8978b605 #9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558 #10 [ffffa65531497ac8] console_unlock at ffffffff89316124 #11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07 #12 [ffffa65531497b68] printk at ffffffff89318306 #13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765 #14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun] #15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun] #16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net] #17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost] #18 [ffffa65531497f10] kthread at ffffffff892d2e72 #19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f Fixes: ef3db4a ("tun: avoid BUG, dump packet on GSO errors") Signed-off-by: Lei Chen <lei.chen@smartx.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20240415020247.2207781-1-lei.chen@smartx.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 769e6a1 ] ui_browser__show() is capturing the input title that is stack allocated memory in hist_browser__run(). Avoid a use after return by strdup-ing the string. Committer notes: Further explanation from Ian Rogers: My command line using tui is: $ sudo bash -c 'rm /tmp/asan.log*; export ASAN_OPTIONS="log_path=/tmp/asan.log"; /tmp/perf/perf mem record -a sleep 1; /tmp/perf/perf mem report' I then go to the perf annotate view and quit. This triggers the asan error (from the log file): ``` ==1254591==ERROR: AddressSanitizer: stack-use-after-return on address 0x7f2813331920 at pc 0x7f28180 65991 bp 0x7fff0a21c750 sp 0x7fff0a21bf10 READ of size 80 at 0x7f2813331920 thread T0 #0 0x7f2818065990 in __interceptor_strlen ../../../../src/libsanitizer/sanitizer_common/sanitizer_common_interceptors.inc:461 #1 0x7f2817698251 in SLsmg_write_wrapped_string (/lib/x86_64-linux-gnu/libslang.so.2+0x98251) #2 0x7f28176984b9 in SLsmg_write_nstring (/lib/x86_64-linux-gnu/libslang.so.2+0x984b9) #3 0x55c94045b365 in ui_browser__write_nstring ui/browser.c:60 #4 0x55c94045c558 in __ui_browser__show_title ui/browser.c:266 #5 0x55c94045c776 in ui_browser__show ui/browser.c:288 #6 0x55c94045c06d in ui_browser__handle_resize ui/browser.c:206 #7 0x55c94047979b in do_annotate ui/browsers/hists.c:2458 #8 0x55c94047fb17 in evsel__hists_browse ui/browsers/hists.c:3412 #9 0x55c940480a0c in perf_evsel_menu__run ui/browsers/hists.c:3527 #10 0x55c940481108 in __evlist__tui_browse_hists ui/browsers/hists.c:3613 #11 0x55c9404813f7 in evlist__tui_browse_hists ui/browsers/hists.c:3661 #12 0x55c93ffa253f in report__browse_hists tools/perf/builtin-report.c:671 #13 0x55c93ffa58ca in __cmd_report tools/perf/builtin-report.c:1141 #14 0x55c93ffaf159 in cmd_report tools/perf/builtin-report.c:1805 #15 0x55c94000c05c in report_events tools/perf/builtin-mem.c:374 #16 0x55c94000d96d in cmd_mem tools/perf/builtin-mem.c:516 #17 0x55c9400e44ee in run_builtin tools/perf/perf.c:350 #18 0x55c9400e4a5a in handle_internal_command tools/perf/perf.c:403 #19 0x55c9400e4e22 in run_argv tools/perf/perf.c:447 #20 0x55c9400e53ad in main tools/perf/perf.c:561 #21 0x7f28170456c9 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #22 0x7f2817045784 in __libc_start_main_impl ../csu/libc-start.c:360 #23 0x55c93ff544c0 in _start (/tmp/perf/perf+0x19a4c0) (BuildId: 84899b0e8c7d3a3eaa67b2eb35e3d8b2f8cd4c93) Address 0x7f2813331920 is located in stack of thread T0 at offset 32 in frame #0 0x55c94046e85e in hist_browser__run ui/browsers/hists.c:746 This frame has 1 object(s): [32, 192) 'title' (line 747) <== Memory access at offset 32 is inside this variable HINT: this may be a false positive if your program uses some custom stack unwind mechanism, swapcontext or vfork ``` hist_browser__run isn't on the stack so the asan error looks legit. There's no clean init/exit on struct ui_browser so I may be trading a use-after-return for a memory leak, but that seems look a good trade anyway. Fixes: 05e8b08 ("perf ui browser: Stop using 'self'") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Cc: Ben Gainey <ben.gainey@arm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: Li Dong <lidong@vivo.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Oliver Upton <oliver.upton@linux.dev> Cc: Paran Lee <p4ranlee@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Cc: Sun Haiyong <sunhaiyong@loongson.cn> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Yanteng Si <siyanteng@loongson.cn> Cc: Yicong Yang <yangyicong@hisilicon.com> Link: https://lore.kernel.org/r/20240507183545.1236093-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/20240617095543.6971-1-jack@suse.cz Link: https://lkml.kernel.org/r/20240614145243.8837-1-jack@suse.cz Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

commit be346c1 upstream. The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 #1 __crash_kexec at ffffffff8c1338fa #2 panic at ffffffff8c1d69b9 #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] #10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] #11 dio_complete at ffffffff8c2b9fa7 #12 do_blockdev_direct_IO at ffffffff8c2bc09f #13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] #14 generic_file_direct_write at ffffffff8c1dcf14 #15 __generic_file_write_iter at ffffffff8c1dd07b #16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] #17 aio_write at ffffffff8c2cc72e #18 kmem_cache_alloc at ffffffff8c248dde #19 do_io_submit at ffffffff8c2ccada #20 do_syscall_64 at ffffffff8c004984 #21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/20240617095543.6971-1-jack@suse.cz Link: https://lkml.kernel.org/r/20240614145243.8837-1-jack@suse.cz Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Heming Zhao <heming.zhao@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 769e6a1 ] ui_browser__show() is capturing the input title that is stack allocated memory in hist_browser__run(). Avoid a use after return by strdup-ing the string. Committer notes: Further explanation from Ian Rogers: My command line using tui is: $ sudo bash -c 'rm /tmp/asan.log*; export ASAN_OPTIONS="log_path=/tmp/asan.log"; /tmp/perf/perf mem record -a sleep 1; /tmp/perf/perf mem report' I then go to the perf annotate view and quit. This triggers the asan error (from the log file): ``` ==1254591==ERROR: AddressSanitizer: stack-use-after-return on address 0x7f2813331920 at pc 0x7f28180 65991 bp 0x7fff0a21c750 sp 0x7fff0a21bf10 READ of size 80 at 0x7f2813331920 thread T0 #0 0x7f2818065990 in __interceptor_strlen ../../../../src/libsanitizer/sanitizer_common/sanitizer_common_interceptors.inc:461 #1 0x7f2817698251 in SLsmg_write_wrapped_string (/lib/x86_64-linux-gnu/libslang.so.2+0x98251) #2 0x7f28176984b9 in SLsmg_write_nstring (/lib/x86_64-linux-gnu/libslang.so.2+0x984b9) #3 0x55c94045b365 in ui_browser__write_nstring ui/browser.c:60 #4 0x55c94045c558 in __ui_browser__show_title ui/browser.c:266 #5 0x55c94045c776 in ui_browser__show ui/browser.c:288 #6 0x55c94045c06d in ui_browser__handle_resize ui/browser.c:206 #7 0x55c94047979b in do_annotate ui/browsers/hists.c:2458 #8 0x55c94047fb17 in evsel__hists_browse ui/browsers/hists.c:3412 #9 0x55c940480a0c in perf_evsel_menu__run ui/browsers/hists.c:3527 #10 0x55c940481108 in __evlist__tui_browse_hists ui/browsers/hists.c:3613 #11 0x55c9404813f7 in evlist__tui_browse_hists ui/browsers/hists.c:3661 #12 0x55c93ffa253f in report__browse_hists tools/perf/builtin-report.c:671 #13 0x55c93ffa58ca in __cmd_report tools/perf/builtin-report.c:1141 #14 0x55c93ffaf159 in cmd_report tools/perf/builtin-report.c:1805 #15 0x55c94000c05c in report_events tools/perf/builtin-mem.c:374 #16 0x55c94000d96d in cmd_mem tools/perf/builtin-mem.c:516 #17 0x55c9400e44ee in run_builtin tools/perf/perf.c:350 #18 0x55c9400e4a5a in handle_internal_command tools/perf/perf.c:403 #19 0x55c9400e4e22 in run_argv tools/perf/perf.c:447 #20 0x55c9400e53ad in main tools/perf/perf.c:561 #21 0x7f28170456c9 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #22 0x7f2817045784 in __libc_start_main_impl ../csu/libc-start.c:360 #23 0x55c93ff544c0 in _start (/tmp/perf/perf+0x19a4c0) (BuildId: 84899b0e8c7d3a3eaa67b2eb35e3d8b2f8cd4c93) Address 0x7f2813331920 is located in stack of thread T0 at offset 32 in frame #0 0x55c94046e85e in hist_browser__run ui/browsers/hists.c:746 This frame has 1 object(s): [32, 192) 'title' (line 747) <== Memory access at offset 32 is inside this variable HINT: this may be a false positive if your program uses some custom stack unwind mechanism, swapcontext or vfork ``` hist_browser__run isn't on the stack so the asan error looks legit. There's no clean init/exit on struct ui_browser so I may be trading a use-after-return for a memory leak, but that seems look a good trade anyway. Fixes: 05e8b08 ("perf ui browser: Stop using 'self'") Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Cc: Ben Gainey <ben.gainey@arm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: Li Dong <lidong@vivo.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Oliver Upton <oliver.upton@linux.dev> Cc: Paran Lee <p4ranlee@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Cc: Sun Haiyong <sunhaiyong@loongson.cn> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Yanteng Si <siyanteng@loongson.cn> Cc: Yicong Yang <yangyicong@hisilicon.com> Link: https://lore.kernel.org/r/20240507183545.1236093-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

@offset

commit 98100e8 upstream. The action force umount(umount -f) will attempt to kill all rpc_task even umount operation may ultimately fail if some files remain open. Consequently, if an action attempts to open a file, it can potentially send two rpc_task to nfs server. NFS CLIENT thread1 thread2 open("file") ... nfs4_do_open _nfs4_do_open _nfs4_open_and_get_state _nfs4_proc_open nfs4_run_open_task /* rpc_task1 */ rpc_run_task rpc_wait_for_completion_task umount -f nfs_umount_begin rpc_killall_tasks rpc_signal_task rpc_task1 been wakeup and return -512 _nfs4_do_open // while loop ... nfs4_run_open_task /* rpc_task2 */ rpc_run_task rpc_wait_for_completion_task While processing an open request, nfsd will first attempt to find or allocate an nfs4_openowner. If it finds an nfs4_openowner that is not marked as NFS4_OO_CONFIRMED, this nfs4_openowner will released. Since two rpc_task can attempt to open the same file simultaneously from the client to server, and because two instances of nfsd can run concurrently, this situation can lead to lots of memory leak. Additionally, when we echo 0 to /proc/fs/nfsd/threads, warning will be triggered. NFS SERVER nfsd1 nfsd2 echo 0 > /proc/fs/nfsd/threads nfsd4_open nfsd4_process_open1 find_or_alloc_open_stateowner // alloc oo1, stateid1 nfsd4_open nfsd4_process_open1 find_or_alloc_open_stateowner // find oo1, without NFS4_OO_CONFIRMED release_openowner unhash_openowner_locked list_del_init(&oo->oo_perclient) // cannot find this oo // from client, LEAK!!! alloc_stateowner // alloc oo2 nfsd4_process_open2 init_open_stateid // associate oo1 // with stateid1, stateid1 LEAK!!! nfs4_get_vfs_file // alloc nfsd_file1 and nfsd_file_mark1 // all LEAK!!! nfsd4_process_open2 ... write_threads ... nfsd_destroy_serv nfsd_shutdown_net nfs4_state_shutdown_net nfs4_state_destroy_net destroy_client __destroy_client // won't find oo1!!! nfsd_shutdown_generic nfsd_file_cache_shutdown kmem_cache_destroy for nfsd_file_slab and nfsd_file_mark_slab // bark since nfsd_file1 // and nfsd_file_mark1 // still alive ======================================================================= BUG nfsd_file (Not tainted): Objects remaining in nfsd_file on __kmem_cache_shutdown() ----------------------------------------------------------------------- Slab 0xffd4000004438a80 objects=34 used=1 fp=0xff11000110e2ad28 flags=0x17ffffc0000240(workingset|head|node=0|zone=2|lastcpupid=0x1fffff) CPU: 4 UID: 0 PID: 757 Comm: sh Not tainted 6.12.0-rc6+ #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 slab_err+0xb0/0xf0 __kmem_cache_shutdown+0x15c/0x310 kmem_cache_destroy+0x66/0x160 nfsd_file_cache_shutdown+0xac/0x210 [nfsd] nfsd_destroy_serv+0x251/0x2a0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1ae/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Disabling lock debugging due to kernel taint Object 0xff11000110e2ac38 @offset=3128 Allocated in nfsd_file_do_acquire+0x20f/0xa30 [nfsd] age=1635 cpu=3 pid=800 nfsd_file_do_acquire+0x20f/0xa30 [nfsd] nfsd_file_acquire_opened+0x5f/0x90 [nfsd] nfs4_get_vfs_file+0x4c9/0x570 [nfsd] nfsd4_process_open2+0x713/0x1070 [nfsd] nfsd4_open+0x74b/0x8b0 [nfsd] nfsd4_proc_compound+0x70b/0xc20 [nfsd] nfsd_dispatch+0x1b4/0x3a0 [nfsd] svc_process_common+0x5b8/0xc50 [sunrpc] svc_process+0x2ab/0x3b0 [sunrpc] svc_handle_xprt+0x681/0xa20 [sunrpc] nfsd+0x183/0x220 [nfsd] kthread+0x199/0x1e0 ret_from_fork+0x31/0x60 ret_from_fork_asm+0x1a/0x30 Add nfs4_openowner_unhashed to help found unhashed nfs4_openowner, and break nfsd4_open process to fix this problem. Cc: stable@vger.kernel.org # v5.4+ Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Yang Erkun <yangerkun@huawei.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

@offset

commit 98100e8 upstream. The action force umount(umount -f) will attempt to kill all rpc_task even umount operation may ultimately fail if some files remain open. Consequently, if an action attempts to open a file, it can potentially send two rpc_task to nfs server. NFS CLIENT thread1 thread2 open("file") ... nfs4_do_open _nfs4_do_open _nfs4_open_and_get_state _nfs4_proc_open nfs4_run_open_task /* rpc_task1 */ rpc_run_task rpc_wait_for_completion_task umount -f nfs_umount_begin rpc_killall_tasks rpc_signal_task rpc_task1 been wakeup and return -512 _nfs4_do_open // while loop ... nfs4_run_open_task /* rpc_task2 */ rpc_run_task rpc_wait_for_completion_task While processing an open request, nfsd will first attempt to find or allocate an nfs4_openowner. If it finds an nfs4_openowner that is not marked as NFS4_OO_CONFIRMED, this nfs4_openowner will released. Since two rpc_task can attempt to open the same file simultaneously from the client to server, and because two instances of nfsd can run concurrently, this situation can lead to lots of memory leak. Additionally, when we echo 0 to /proc/fs/nfsd/threads, warning will be triggered. NFS SERVER nfsd1 nfsd2 echo 0 > /proc/fs/nfsd/threads nfsd4_open nfsd4_process_open1 find_or_alloc_open_stateowner // alloc oo1, stateid1 nfsd4_open nfsd4_process_open1 find_or_alloc_open_stateowner // find oo1, without NFS4_OO_CONFIRMED release_openowner unhash_openowner_locked list_del_init(&oo->oo_perclient) // cannot find this oo // from client, LEAK!!! alloc_stateowner // alloc oo2 nfsd4_process_open2 init_open_stateid // associate oo1 // with stateid1, stateid1 LEAK!!! nfs4_get_vfs_file // alloc nfsd_file1 and nfsd_file_mark1 // all LEAK!!! nfsd4_process_open2 ... write_threads ... nfsd_destroy_serv nfsd_shutdown_net nfs4_state_shutdown_net nfs4_state_destroy_net destroy_client __destroy_client // won't find oo1!!! nfsd_shutdown_generic nfsd_file_cache_shutdown kmem_cache_destroy for nfsd_file_slab and nfsd_file_mark_slab // bark since nfsd_file1 // and nfsd_file_mark1 // still alive ======================================================================= BUG nfsd_file (Not tainted): Objects remaining in nfsd_file on __kmem_cache_shutdown() ----------------------------------------------------------------------- Slab 0xffd4000004438a80 objects=34 used=1 fp=0xff11000110e2ad28 flags=0x17ffffc0000240(workingset|head|node=0|zone=2|lastcpupid=0x1fffff) CPU: 4 UID: 0 PID: 757 Comm: sh Not tainted 6.12.0-rc6+ #19 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x53/0x70 slab_err+0xb0/0xf0 __kmem_cache_shutdown+0x15c/0x310 kmem_cache_destroy+0x66/0x160 nfsd_file_cache_shutdown+0xac/0x210 [nfsd] nfsd_destroy_serv+0x251/0x2a0 [nfsd] nfsd_svc+0x125/0x1e0 [nfsd] write_threads+0x16a/0x2a0 [nfsd] nfsctl_transaction_write+0x74/0xa0 [nfsd] vfs_write+0x1ae/0x6d0 ksys_write+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Disabling lock debugging due to kernel taint Object 0xff11000110e2ac38 @offset=3128 Allocated in nfsd_file_do_acquire+0x20f/0xa30 [nfsd] age=1635 cpu=3 pid=800 nfsd_file_do_acquire+0x20f/0xa30 [nfsd] nfsd_file_acquire_opened+0x5f/0x90 [nfsd] nfs4_get_vfs_file+0x4c9/0x570 [nfsd] nfsd4_process_open2+0x713/0x1070 [nfsd] nfsd4_open+0x74b/0x8b0 [nfsd] nfsd4_proc_compound+0x70b/0xc20 [nfsd] nfsd_dispatch+0x1b4/0x3a0 [nfsd] svc_process_common+0x5b8/0xc50 [sunrpc] svc_process+0x2ab/0x3b0 [sunrpc] svc_handle_xprt+0x681/0xa20 [sunrpc] nfsd+0x183/0x220 [nfsd] kthread+0x199/0x1e0 ret_from_fork+0x31/0x60 ret_from_fork_asm+0x1a/0x30 Add nfs4_openowner_unhashed to help found unhashed nfs4_openowner, and break nfsd4_open process to fix this problem. Cc: stable@vger.kernel.org # v5.4+ Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Yang Erkun <yangerkun@huawei.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit addresses a circular locking dependency issue within the GFX isolation mechanism. The problem was identified by a warning indicating a potential deadlock due to inconsistent lock acquisition order. - The `amdgpu_gfx_enforce_isolation_ring_begin_use` and `amdgpu_gfx_enforce_isolation_ring_end_use` functions previously acquired `enforce_isolation_mutex` and called `amdgpu_gfx_kfd_sch_ctrl`, leading to potential deadlocks. ie., If `amdgpu_gfx_kfd_sch_ctrl` is called while `enforce_isolation_mutex` is held, and `amdgpu_gfx_enforce_isolation_handler` is called while `kfd_sch_mutex` is held, it can create a circular dependency. By ensuring consistent lock usage, this fix resolves the issue: [ 606.297333] ====================================================== [ 606.297343] WARNING: possible circular locking dependency detected [ 606.297353] 6.10.0-amd-mlkd-610-311224-lof #19 Tainted: G OE [ 606.297365] ------------------------------------------------------ [ 606.297375] kworker/u96:3/3825 is trying to acquire lock: [ 606.297385] ffff9aa64e431cb8 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}, at: __flush_work+0x232/0x610 [ 606.297413] but task is already holding lock: [ 606.297423] ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.297725] which lock already depends on the new lock. [ 606.297738] the existing dependency chain (in reverse order) is: [ 606.297749] -> #2 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}: [ 606.297765] __mutex_lock+0x85/0x930 [ 606.297776] mutex_lock_nested+0x1b/0x30 [ 606.297786] amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.298007] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.298225] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.298412] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.298603] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.298866] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.298880] process_one_work+0x21e/0x680 [ 606.298890] worker_thread+0x190/0x350 [ 606.298899] kthread+0xe7/0x120 [ 606.298908] ret_from_fork+0x3c/0x60 [ 606.298919] ret_from_fork_asm+0x1a/0x30 [ 606.298929] -> #1 (&adev->enforce_isolation_mutex){+.+.}-{3:3}: [ 606.298947] __mutex_lock+0x85/0x930 [ 606.298956] mutex_lock_nested+0x1b/0x30 [ 606.298966] amdgpu_gfx_enforce_isolation_handler+0x87/0x370 [amdgpu] [ 606.299190] process_one_work+0x21e/0x680 [ 606.299199] worker_thread+0x190/0x350 [ 606.299208] kthread+0xe7/0x120 [ 606.299217] ret_from_fork+0x3c/0x60 [ 606.299227] ret_from_fork_asm+0x1a/0x30 [ 606.299236] -> #0 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}: [ 606.299257] __lock_acquire+0x16f9/0x2810 [ 606.299267] lock_acquire+0xd1/0x300 [ 606.299276] __flush_work+0x250/0x610 [ 606.299286] cancel_delayed_work_sync+0x71/0x80 [ 606.299296] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu] [ 606.299509] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.299723] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.299909] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.300101] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.300355] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.300369] process_one_work+0x21e/0x680 [ 606.300378] worker_thread+0x190/0x350 [ 606.300387] kthread+0xe7/0x120 [ 606.300396] ret_from_fork+0x3c/0x60 [ 606.300406] ret_from_fork_asm+0x1a/0x30 [ 606.300416] other info that might help us debug this: [ 606.300428] Chain exists of: (work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work) --> &adev->enforce_isolation_mutex --> &adev->gfx.kfd_sch_mutex [ 606.300458] Possible unsafe locking scenario: [ 606.300468] CPU0 CPU1 [ 606.300476] ---- ---- [ 606.300484] lock(&adev->gfx.kfd_sch_mutex); [ 606.300494] lock(&adev->enforce_isolation_mutex); [ 606.300508] lock(&adev->gfx.kfd_sch_mutex); [ 606.300521] lock((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)); [ 606.300536] *** DEADLOCK *** [ 606.300546] 5 locks held by kworker/u96:3/3825: [ 606.300555] #0: ffff9aa5aa1f5d58 ((wq_completion)comp_1.1.0){+.+.}-{0:0}, at: process_one_work+0x3f5/0x680 [ 606.300577] #1: ffffaa53c3c97e40 ((work_completion)(&sched->work_run_job)){+.+.}-{0:0}, at: process_one_work+0x1d6/0x680 [ 606.300600] #2: ffff9aa64e463c98 (&adev->enforce_isolation_mutex){+.+.}-{3:3}, at: amdgpu_gfx_enforce_isolation_ring_begin_use+0x1c3/0x5d0 [amdgpu] [ 606.300837] #3: ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.301062] #4: ffffffff8c1a5660 (rcu_read_lock){....}-{1:2}, at: __flush_work+0x70/0x610 [ 606.301083] stack backtrace: [ 606.301092] CPU: 14 PID: 3825 Comm: kworker/u96:3 Tainted: G OE 6.10.0-amd-mlkd-610-311224-lof #19 [ 606.301109] Hardware name: Gigabyte Technology Co., Ltd. X570S GAMING X/X570S GAMING X, BIOS F7 03/22/2024 [ 606.301124] Workqueue: comp_1.1.0 drm_sched_run_job_work [gpu_sched] [ 606.301140] Call Trace: [ 606.301146] <TASK> [ 606.301154] dump_stack_lvl+0x9b/0xf0 [ 606.301166] dump_stack+0x10/0x20 [ 606.301175] print_circular_bug+0x26c/0x340 [ 606.301187] check_noncircular+0x157/0x170 [ 606.301197] ? register_lock_class+0x48/0x490 [ 606.301213] __lock_acquire+0x16f9/0x2810 [ 606.301230] lock_acquire+0xd1/0x300 [ 606.301239] ? __flush_work+0x232/0x610 [ 606.301250] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.301261] ? mark_held_locks+0x54/0x90 [ 606.301274] ? __flush_work+0x232/0x610 [ 606.301284] __flush_work+0x250/0x610 [ 606.301293] ? __flush_work+0x232/0x610 [ 606.301305] ? __pfx_wq_barrier_func+0x10/0x10 [ 606.301318] ? mark_held_locks+0x54/0x90 [ 606.301331] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.301345] cancel_delayed_work_sync+0x71/0x80 [ 606.301356] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu] [ 606.301661] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.302050] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.302069] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.302452] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.302862] ? drm_sched_entity_error+0x82/0x190 [gpu_sched] [ 606.302890] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.303366] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.303388] process_one_work+0x21e/0x680 [ 606.303409] worker_thread+0x190/0x350 [ 606.303424] ? __pfx_worker_thread+0x10/0x10 [ 606.303437] kthread+0xe7/0x120 [ 606.303449] ? __pfx_kthread+0x10/0x10 [ 606.303463] ret_from_fork+0x3c/0x60 [ 606.303476] ? __pfx_kthread+0x10/0x10 [ 606.303489] ret_from_fork_asm+0x1a/0x30 [ 606.303512] </TASK> v2: Refactor lock handling to resolve circular dependency (Alex) - Introduced a `sched_work` flag to defer the call to `amdgpu_gfx_kfd_sch_ctrl` until after releasing `enforce_isolation_mutex`. - This change ensures that `amdgpu_gfx_kfd_sch_ctrl` is called outside the critical section, preventing the circular dependency and deadlock. - The `sched_work` flag is set within the mutex-protected section if conditions are met, and the actual function call is made afterward. - This approach ensures consistent lock acquisition order. Fixes: afefd6f ("drm/amdgpu: Implement Enforce Isolation Handler for KGD/KFD serialization") Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> (cherry picked from commit 0b6b2dd) Cc: stable@vger.kernel.org

[ Upstream commit 1e8c193 ] This commit addresses a circular locking dependency issue within the GFX isolation mechanism. The problem was identified by a warning indicating a potential deadlock due to inconsistent lock acquisition order. - The `amdgpu_gfx_enforce_isolation_ring_begin_use` and `amdgpu_gfx_enforce_isolation_ring_end_use` functions previously acquired `enforce_isolation_mutex` and called `amdgpu_gfx_kfd_sch_ctrl`, leading to potential deadlocks. ie., If `amdgpu_gfx_kfd_sch_ctrl` is called while `enforce_isolation_mutex` is held, and `amdgpu_gfx_enforce_isolation_handler` is called while `kfd_sch_mutex` is held, it can create a circular dependency. By ensuring consistent lock usage, this fix resolves the issue: [ 606.297333] ====================================================== [ 606.297343] WARNING: possible circular locking dependency detected [ 606.297353] 6.10.0-amd-mlkd-610-311224-lof #19 Tainted: G OE [ 606.297365] ------------------------------------------------------ [ 606.297375] kworker/u96:3/3825 is trying to acquire lock: [ 606.297385] ffff9aa64e431cb8 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}, at: __flush_work+0x232/0x610 [ 606.297413] but task is already holding lock: [ 606.297423] ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.297725] which lock already depends on the new lock. [ 606.297738] the existing dependency chain (in reverse order) is: [ 606.297749] -> #2 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}: [ 606.297765] __mutex_lock+0x85/0x930 [ 606.297776] mutex_lock_nested+0x1b/0x30 [ 606.297786] amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.298007] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.298225] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.298412] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.298603] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.298866] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.298880] process_one_work+0x21e/0x680 [ 606.298890] worker_thread+0x190/0x350 [ 606.298899] kthread+0xe7/0x120 [ 606.298908] ret_from_fork+0x3c/0x60 [ 606.298919] ret_from_fork_asm+0x1a/0x30 [ 606.298929] -> #1 (&adev->enforce_isolation_mutex){+.+.}-{3:3}: [ 606.298947] __mutex_lock+0x85/0x930 [ 606.298956] mutex_lock_nested+0x1b/0x30 [ 606.298966] amdgpu_gfx_enforce_isolation_handler+0x87/0x370 [amdgpu] [ 606.299190] process_one_work+0x21e/0x680 [ 606.299199] worker_thread+0x190/0x350 [ 606.299208] kthread+0xe7/0x120 [ 606.299217] ret_from_fork+0x3c/0x60 [ 606.299227] ret_from_fork_asm+0x1a/0x30 [ 606.299236] -> #0 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}: [ 606.299257] __lock_acquire+0x16f9/0x2810 [ 606.299267] lock_acquire+0xd1/0x300 [ 606.299276] __flush_work+0x250/0x610 [ 606.299286] cancel_delayed_work_sync+0x71/0x80 [ 606.299296] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu] [ 606.299509] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.299723] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.299909] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.300101] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.300355] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.300369] process_one_work+0x21e/0x680 [ 606.300378] worker_thread+0x190/0x350 [ 606.300387] kthread+0xe7/0x120 [ 606.300396] ret_from_fork+0x3c/0x60 [ 606.300406] ret_from_fork_asm+0x1a/0x30 [ 606.300416] other info that might help us debug this: [ 606.300428] Chain exists of: (work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work) --> &adev->enforce_isolation_mutex --> &adev->gfx.kfd_sch_mutex [ 606.300458] Possible unsafe locking scenario: [ 606.300468] CPU0 CPU1 [ 606.300476] ---- ---- [ 606.300484] lock(&adev->gfx.kfd_sch_mutex); [ 606.300494] lock(&adev->enforce_isolation_mutex); [ 606.300508] lock(&adev->gfx.kfd_sch_mutex); [ 606.300521] lock((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)); [ 606.300536] *** DEADLOCK *** [ 606.300546] 5 locks held by kworker/u96:3/3825: [ 606.300555] #0: ffff9aa5aa1f5d58 ((wq_completion)comp_1.1.0){+.+.}-{0:0}, at: process_one_work+0x3f5/0x680 [ 606.300577] #1: ffffaa53c3c97e40 ((work_completion)(&sched->work_run_job)){+.+.}-{0:0}, at: process_one_work+0x1d6/0x680 [ 606.300600] #2: ffff9aa64e463c98 (&adev->enforce_isolation_mutex){+.+.}-{3:3}, at: amdgpu_gfx_enforce_isolation_ring_begin_use+0x1c3/0x5d0 [amdgpu] [ 606.300837] #3: ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu] [ 606.301062] #4: ffffffff8c1a5660 (rcu_read_lock){....}-{1:2}, at: __flush_work+0x70/0x610 [ 606.301083] stack backtrace: [ 606.301092] CPU: 14 PID: 3825 Comm: kworker/u96:3 Tainted: G OE 6.10.0-amd-mlkd-610-311224-lof #19 [ 606.301109] Hardware name: Gigabyte Technology Co., Ltd. X570S GAMING X/X570S GAMING X, BIOS F7 03/22/2024 [ 606.301124] Workqueue: comp_1.1.0 drm_sched_run_job_work [gpu_sched] [ 606.301140] Call Trace: [ 606.301146] <TASK> [ 606.301154] dump_stack_lvl+0x9b/0xf0 [ 606.301166] dump_stack+0x10/0x20 [ 606.301175] print_circular_bug+0x26c/0x340 [ 606.301187] check_noncircular+0x157/0x170 [ 606.301197] ? register_lock_class+0x48/0x490 [ 606.301213] __lock_acquire+0x16f9/0x2810 [ 606.301230] lock_acquire+0xd1/0x300 [ 606.301239] ? __flush_work+0x232/0x610 [ 606.301250] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.301261] ? mark_held_locks+0x54/0x90 [ 606.301274] ? __flush_work+0x232/0x610 [ 606.301284] __flush_work+0x250/0x610 [ 606.301293] ? __flush_work+0x232/0x610 [ 606.301305] ? __pfx_wq_barrier_func+0x10/0x10 [ 606.301318] ? mark_held_locks+0x54/0x90 [ 606.301331] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.301345] cancel_delayed_work_sync+0x71/0x80 [ 606.301356] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu] [ 606.301661] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu] [ 606.302050] ? srso_alias_return_thunk+0x5/0xfbef5 [ 606.302069] amdgpu_ring_alloc+0x48/0x70 [amdgpu] [ 606.302452] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu] [ 606.302862] ? drm_sched_entity_error+0x82/0x190 [gpu_sched] [ 606.302890] amdgpu_job_run+0xac/0x1e0 [amdgpu] [ 606.303366] drm_sched_run_job_work+0x24f/0x430 [gpu_sched] [ 606.303388] process_one_work+0x21e/0x680 [ 606.303409] worker_thread+0x190/0x350 [ 606.303424] ? __pfx_worker_thread+0x10/0x10 [ 606.303437] kthread+0xe7/0x120 [ 606.303449] ? __pfx_kthread+0x10/0x10 [ 606.303463] ret_from_fork+0x3c/0x60 [ 606.303476] ? __pfx_kthread+0x10/0x10 [ 606.303489] ret_from_fork_asm+0x1a/0x30 [ 606.303512] </TASK> v2: Refactor lock handling to resolve circular dependency (Alex) - Introduced a `sched_work` flag to defer the call to `amdgpu_gfx_kfd_sch_ctrl` until after releasing `enforce_isolation_mutex`. - This change ensures that `amdgpu_gfx_kfd_sch_ctrl` is called outside the critical section, preventing the circular dependency and deadlock. - The `sched_work` flag is set within the mutex-protected section if conditions are met, and the actual function call is made afterward. - This approach ensures consistent lock acquisition order. Fixes: afefd6f ("drm/amdgpu: Implement Enforce Isolation Handler for KGD/KFD serialization") Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

Frank-Buss and others added 9 commits May 8, 2012 01:10

I2C-GPIO driver enabled

7a0de86

Merge branch 'rpi-patches' of git://github.com/raspberrypi/linux into…

67350f7

… rpi-patches

changed driver init order, because GPIO is architecture level and sho…

04985ff

…uld be loaded before all other modules

structure only needed whe I2C_GPIO ins enabled

b51c6a3

bcm2708: Fix i2c platform device registration when CONFIG_I2C_GPIO=m

28e096c

Merge pull request #1 from GadgetUK/rpi-patches

85cba76

bcm2708: Fix i2c platform device registration when CONFIG_I2C_GPIO=m

Merge branch 'rpi-patches' of git://github.com/raspberrypi/linux into…

68efe15

… rpi-patches

fine tuning for 100 kHz I2C bus speed

891b628

enabling I2C-GPIO as a module

ec7d9a4

popcornmix closed this May 26, 2012

gregd72002 mentioned this pull request Aug 28, 2012

Bluetooth TX Timeout Issue #66

Closed

castalla mentioned this pull request Jan 25, 2013

Bluetooth issues #200

Closed

marty45714 mentioned this pull request Feb 24, 2024

Wayland crashes (segmentation fault) after executing "wlr-randr" command #5984

Closed

ned14 mentioned this pull request Jan 23, 2025

Official Raspberry Pi NVMe SSD drive (Biwin) ignores TRIM commands #6627

Closed

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

I2C with the Linux bitbanging interface activated #19

I2C with the Linux bitbanging interface activated #19

FrankBuss commented May 11, 2012

popcornmix commented May 26, 2012

FrankBuss commented May 26, 2012

asb commented May 26, 2012

I2C with the Linux bitbanging interface activated #19

I2C with the Linux bitbanging interface activated #19

Conversation

FrankBuss commented May 11, 2012

popcornmix commented May 26, 2012

FrankBuss commented May 26, 2012

asb commented May 26, 2012